排序方式: 共有50条查询结果,搜索用时 31 毫秒
1.
2.
The samples of single crystal superalloy DD6 are grit blasted and then heat treated either with the standard heat treatment procedure or in the temperature range of 1 000-1 250 °C for 4-16 h at vacuum atmosphere, then the recrystallization behavior of DD6 alloy is investigated. The results show that the equiaxed recrystallization grains form in the γ phase region where the as-cast γ′ phases have been dissolved completely, and cellular recrystallization forms in the region where the as-cast γ′ phases have been dissolved partially. The cellular recrystallization area consists of cellular grains, and the cellular grain consists of cubic γ′ phase, lamellar γ′ phase and γ+γ′ The coexistence of the equiaxed recrystallization zones and cellular recrystallization zones is a recrystallized characteristic of the cold worked single crystal samples which are heat treated at a temperature lower than the solution temperature. When the heating temperature is higher than 1 150 °C, with the increase of heat treating temperature, the equiaxed recrystallization zone expands, whereas the cellular recrystallization zone shrinks. All the deformed regions are consumed by equiaxed recrystallization after annealing at solution temperature. 相似文献
3.
4.
5.
用高纯α-Fe在GLEEBLE-1500热模拟机上率进行了热压缩试验。变形温度分别为550℃,700℃,800℃和900℃,应变速率分别为0.001s~(-1),0.01s~(-1),0.1s~(-1),1s~(-1)和10s~(-1)。对其热压缩过程中的显微结构变化及真应力-真应变曲线进行的研究结果表明,形变温度的增加和应变速率降低有利于动态再结晶的进行;对动态再结晶与Z参数关系的研究结果表明,在一定的Z参数范围内即25<1nZ<37,高纯α-Fe可以发生动态再结晶,并给出动态再结晶图。 相似文献
6.
7.
采用Gleeble-1500D热模拟试验机对原位合成TiB2(质量分数,8%)/6351复合材料在不同变形温度和不同应变速率条件下的热变形特性进行了研究,利用透射电镜(TEM)和光学显微镜分析了压缩后试样的微观组织.结果表明, 材料的流变应力随变形温度的升高而降低,随应变速率的提高而增大;材料的流变行为主要表现为加工硬化、动态回复和动态再结晶;相应的显微组织特征为:位错网络、混乱的位错团和胞状结构,亚晶及等轴晶.在应变速率和变形温度均较低时,增强体颗粒周围的基体中形成高密度位错区,但随变形温度的升高而减少;在应变速率较高时,增强体颗粒和基体的界面处开裂甚至增强体颗粒本身发生破碎. 相似文献
8.
9.
基于形核的Gibbs-Thomson关系理论和由晶粒尺寸效应引起的优势生长机制。综合各种理论,建立了铜再结晶织构解析式数学分析模型。计算机模拟结果表明,在较慢的加快速度下,完全再结晶时织构为单一的立方组分;在快速加热条件下,完全再结晶时织构可由立方织构组分和保留的冷轧织构组分所组成;再结晶织构受加热速度的影响。 相似文献
10.
表面再结晶层对DZA定向凝固合金低周疲劳性能影响 总被引:3,自引:2,他引:3
针对DZ4定向凝固合金表面再结晶层对材料性能的影响进行了低周疲劳实验研究,并通过岛津SEM伺服疲劳试验机进行表面裂纹实时观察跟踪.研究结果表明,表面再结晶层的存在对材料性能明显产生负面作用,低周疲劳寿命大大降低.不同喷丸强度试件在相同的高温退火条件下形成的再结晶具有不同的再结晶形态,高喷丸强度再结晶更加完全,晶界清晰平直,晶粒有长大的趋势.表层再结晶形态也对疲劳寿命的降低程度以及疲劳微裂纹萌生寿命和裂纹密度有较大的影响.较高喷丸强度形成的再结晶层的试件疲劳寿命降低较少,表面微裂纹萌生较晚,裂纹密度也很低.低喷丸强度试件表面微裂纹大量萌生,密度非常高.再结晶层的晶界开裂是导致表面微裂纹大量萌生的根源,从而导致疲劳寿命大幅度降低. 相似文献