多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

基于压力信号分析的轴流式压气机失速预测

为了得到压气机工作状态的稳定观测点,并建立压气机近喘失速工作状态与压气机压力信号的相关关系,本文针对低速双级轴流式压气机,分别进行了均匀进气及畸变进气条件下不同转速的近喘失速试验,实时动态测量标定压气机由正常工作到失速工况下压力信号,并在时域内提出了一种基于自相关系数的压气机失速预测算法,对进口、出口以及压气机首级转子叶尖位置压力信号预测分析。结果表明所提出的预测算法具有良好的失速预测能力,且发现叶尖处离叶片前缘20%的位置,最适宜作为压气机失速预测的观测点,此时压气机叶尖压力自相关性数据与压气机喘振裕度具有明显的单调相关性。     

复杂凸凹曲率飞机蒙皮充液成形技术研究与应用

随着飞机气动、隐身等性能要求的提高,飞机外形曲率更加异形化,大量应用复杂凸凹曲率蒙皮,传统的拉伸成形方法已经不能完全满足新一代飞机蒙皮加工的要求。基于生产某型号飞机复杂凸凹曲率蒙皮这一背景,介绍了充液成形基本原理及关键技术,利用有限元数值模拟方法,分析板材充液成形过程中液室压力、厚度减薄率、板材失稳及贴胎度的变化规律,优化工艺参数,并且根据数值模拟结果指导工业生产。理论分析和现场实践证明:充液成形技术为复杂凸凹曲率蒙皮零件的制造提供了新的工艺方法,满足新一代飞机的凸凹曲率外形蒙皮的制造要求。     

某型飞机空中受油管自动开锁故障分析

针对某型飞机空中受油管在收上位置钢珠锁自动开锁故障,对空中受油管液压收放系统、电路控制系统、收上位置钢珠锁工作原理进行分析,比对钢珠锁开锁压力理论计算和收放系统回油压力测试试验结果,找出空中受油管收上位置钢珠锁自动开锁原因,提出改进建议。     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

跨介质航行器波浪环境入水流场演变和运动特性研究

跨介质航行器是一种既可以在空中飞行又可以在水下潜航的新概念航行器,基于仿生学原理,提出一种通过改变外形实现水空介质跨越的航行器模型,通过入水试验装置和计算流体动力学方法,对航行器带攻角从空气到水的介质跨越过程进行了试验和数值仿真研究,得到了跨介质入水过程航行器的运动姿态和入水空泡形态,并通过数值仿真得到了航行器的升力、阻力、速度和加速度演化规律。同时基于数值模拟方法对有波浪情况和静水情况下航行器入水过程空泡演变以及运动特性进行对比。结果表明:提出的航行器构型在水中具有较好的姿态调整能力,波浪的有无和波高的不同都会对航行体入水运动特性造成影响。     

大涵道比风扇/增压级进气畸变数值模拟研究

为探究进口总压畸变下大涵道比风扇/增压级内部流场的主要特征，基于三维彻体力模型的思想，开发了一套能够实现风扇/增压级内外涵联算功能的三维数值计算程序。利用该程序模拟了某大涵道比风扇/增压级在周向总压畸变进气下的三维流场。计算结果表明：大涵道比风扇单转子不同叶高处的畸变传递特征差异较大，转子出口总压畸变强度由叶根到叶尖逐渐降低，在叶尖处衰减为最小值1.5%；在转子出口相应诱导出的总温畸变强度由叶根到叶尖逐渐升高，在叶尖处达到最大值1.4%；进口周向总压畸变导致风扇转子总压比下降0.5%，而风扇转子出口形成的总压总温复合畸变导致增压级总压比下降2%；总压畸变在增压级中呈逐级衰减趋势，而高温畸变区的周向范围在逐级增加。     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

基于遥测数据的无人机气动参数辨识方法研究

针对无人机在高空低速飞行时易受风场影响及在数据分析时遥测数据不完备的问题,进行了气动参数辨识方法研究,提出了基于空速管平面矢量三角形的风场估计方法及基于风场信息修正的气动角估计方法。以某型无人机为例,对遥测数据进行了充分分析与信息综合,运用逐步回归方法进行了纵向气动参数辨识,并进行了实验验证。结果表明,模型计算结果与实测数据吻合较好,说明所提方法有效。考虑到辨识模型的数学本质,该方法对其他固定翼无人机同样适用。