Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

A review of friction stir joining of SiCp/Al composites

SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace, automotive industry and other fields. Due to the huge difference in performance between SiC particles and matrix alloys, traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites. Friction stir joining (friction stir welding), as a solid phase joining process, has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process. Although some progress has been made in recent years, there are still full of challenges. In this paper, the research status of friction stir joining of SiCp/Al composites in recent years is expatiated, including the weldability of SiCp/Al composites, the macrostructure and the microstructure of joints, mechanical properties of joints, and tool wear and monitoring. Furthermore, the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.     

某机载印制电路板在模拟海洋大气环境中腐蚀行为

根据航空机载设备在装备中的局部使用环境、热带海洋环境特征和主要环境因素影响作用等,设计了印制电摘路板(Printed Circuit Board,PCB)在模拟热带海洋大气环境中的盐雾和交变湿热组合循环试验方案。通过开展 PCB的组合循环试验,采用体式显微镜和 SEM电镜等研究分析了不同试验时间下的 PCB的腐蚀行为和电气性能变化规律。结果表明:PCB的腐蚀主要在焊点、焊盘、印制导线和引线头等金属部位;电气性能受表观腐蚀的影响,其接触电阻在试验后增幅达到 50%且受是否带电试验的影响较小。同层间、异层间绝缘电阻变化规律相似,主要分为 2个阶段:前 1 000 h其绝缘电阻较为平稳;试验 1 000 h后则出现明显的下降趋势,最终降低在 1~4 GΩ之间,且整个循环试验中 PCB均能承受 500 V交流电压 60 s。     

温度参数下轴编C/C复合材料的超高温热结构性能分析

为了研究轴编碳/碳（C/C）复合材料的超高温热结构性能,开展了2800℃超高温载荷下复合材料的拉伸实验,表征了复合材料组分材料的高温失效形貌;提出了立方体单胞和正六棱柱单胞的温度周期性边界条件的算法和预测复合材料等效热结构参数的方法,在材料属性各向同性正六棱柱单胞模型上验证了方法的正确性;最后建立了轴编C/C复合材料的代表性体积单元,计算了复合材料随温度载荷变化下的等效热结构参数,与实验数据进行了对比分析。分析表明：开展的轴编C/C复合材料的超高温拉伸实验,可以得到复合材料在2800℃载荷下复合材料的等效刚度值,同时分析了轴向试件和径向试件的高温失效机理,径向试件的纤维束拉伸强度对复合材料的径向拉伸强度起到决定性的作用。在应用位移以及温度周期性边界条件的基础上,提出的方法可以得到随温度载荷变化下复合材料的等效热结构参数,得出复合材料在横向满足近似各向同性的特性,预测结果表明只改变温度参数下复合材料的等效热导率不会发生改变。提出的方法同样也适用于其他编织复合材料的热结构性能研究。     

三维五向编织复合材料的冲击压缩特性及破坏机制

利用分离式霍普金森压杆(split Hopkinson pressure bar,SHPB)实验系统和高速摄像技术对三维五向碳/环氧编织复合材料的动态压缩特性进行研究。通过对编织角为22.3°的试样分别进行沿纵向和横向方向的冲击压缩实验,得到材料在200~1200 s^-1应变率范围内的应力应变曲线,并结合高速摄像记录的动态压缩过程,对不同应变率下材料在高速变形下的渐进破坏规律进行分析。同时,综合试样的宏观破坏特征和微观断口形貌特征,进一步分析材料的破坏模式及破坏机理。结果表明:随着应变率的增加,材料在纵向和横向均具有一定的应变率强化效应,在横向方向的应变率强化效应更为显著;不同加载方向下材料的渐进破坏过程、应力应变曲线特征以及破坏方式均具有明显差异,且随着应变率的增加而发生改变。     

TIG补焊对2219铝合金搅拌摩擦焊接接头微观组织及性能影响

通过对原始搅拌摩擦焊（FSW）接头中间位置进行缺口挖补以模拟焊缝缺陷,采用钨极氩弧焊（TIG）补焊对其进行焊缝缺陷修复试验,研究该补焊工艺对接头微观组织及力学性能的影响规律,为贮箱的FSW焊缝性能评价提供技术支撑和后续工程指导。结果表明,相较于FSW接头,补焊接头TIG焊缝区主要由较大的等轴树枝晶组成,且与FSW焊缝交界处相互掺杂着粗大等轴晶和细小等轴晶;补焊接头固溶区受热循环影响较大,晶粒较为粗大,而过时效区受热循环影响较小,会发生过时效化并形成软化区。补焊接头抗拉强度与延伸率相较于原始FSW接头有所降低,硬度分布大致呈“W”形,WNZ区为硬度值最低处;补焊接头断裂位置始于焊趾处,断口存在大量韧窝,同时韧窝内存在第二相粒子,呈现韧性断裂机制。     

F12/环氧复合材料力学性能研究

测定了Ｆ１２／环氧复合材料的基本力学性能,并比较了Ｆ１２纤维在单向板、强力环及薄壁容器中的纤维强度转化率。实验结果表明,Ｆ１２／环氧单向复合材料与其ＮＯＬ环的拉伸强度相近,而薄壁容器中的复合强度约为单向拉伸强度的６０％,但三种复合材料的纤维强度转化率相近,约为（７０．１±１．６）％。     

浸胶丝束拉伸强度统计分布研究

采用数理统计分析方法,定量比较浸胶丝束拉伸强度实验分布与理论正态分布和Weibull分布的偏离。结果表明,丝束强度分布受纤维种类和基体性能影响。在95％置信度下,浸胶丝束强度分布既可用正态分布描述,也可用Weibull分布描述;但随着基体韧性的提高,浸胶丝束强度分布呈现由正态分布向Weibull分布过渡的趋势。     

织物细观结构参数对编织复合材料弹性性能的影响

根据作者提出的二维波纹细观力学模型,在考虑了实际织物结构中存在的经向和纬向纤维的波纹;相邻纤维束之间的间隙;纤维束的横截面尺寸和织物的叠层构造状态对编织复合材料弹性性能的影响下,给出了织物细观结构参数与编织复合材料弹性性能之间的变化关系。通过参数分析探讨了不同结构参数对编织复合材料弹性性能的影响。     

GC－4高强度钢化学短裂纹特性研究

采用恒ΔＫ法对ＧＣ－４钢在３．５％ＮａＣｌ溶液中化学短裂纹特性进行了试验研究。结果表明：恒ΔＫ时裂纹扩展的ｄａ／ｄＮ－ａ曲线存在临界裂纹尺寸ａ。当ａ＜ａ时,显示化学短裂纹效应。ａ值几乎不受加载频率、应力比和ΔＫ水平的影响;化学短裂纹特征扩展速率与长裂纹扩展速率之比是各种力学参量的弱函数。依据分析给出化学短裂纹扩展速率与裂纹尺寸之间的关系。