2. 5D 衍生结构SiO2 f / SiO2 复合材料的经向力学性能

以几种不同的2.5D衍生结构织物为增强体,制备了法向增强、经向增强及经法向增强2.5D Si O2f/Si O2复合材料,比较了上述材料与现有2.5D Si O2f/Si O2复合材料的经向力学性能,并研究了经法向增强2.5D结构复合材料中增强纱比例、纤维体积分数与材料性能之间的关系,对织物结构进行了优化。结果表明,经法向增强2.5D Si O2f/Si O2复合材料的经向力学性能较现有2.5D复合材料有显著提高,该材料在较低密度下(1.6 g/cm3),经向拉伸强度与现有材料(1.65 g/cm3)持平,且经向压缩强度接近现有材料的4.3倍。     

酚醛树脂炭的合成及力学性能研究

为了表征多孔炭泡沫材料基体的结构与力学性能,采用碱催化法制备热固性酚醛树脂,经固化、高温炭化处理合成多孔炭泡沫材料的基体——酚醛树脂炭。研究酚醛树脂炭的微观结构、压缩强度及压缩断裂韧性。结果表明:酚醛树脂炭结构以树脂炭基体、微孔和微裂纹为主,其碳元素以sp3杂化的非晶炭形式存在;压缩强度为8.58 MPa,压缩断裂特征为脆性断裂模式;酚醛树脂炭的压缩断裂韧性较差,断裂过程中吸收的总能量为0.135 MJ/m3。     

材料特性对热障涂层合理压入深度的影响

基于有限元计算方法和量纲分析原理提出了热障涂层合理压入深度的确定方法,并研究了涂层及基体材料特性对合理压入深度的影响.首先,根据量纲分析原理提出了合理压入深度的无量纲表达式;其次基于锥形压头识别理想弹塑性材料的材料特性的方法,提出合理压入深度的确定方法;最后研究了各无量纲因素对合理压入深度的影响.研究发现基体的弹性模量对合理压入深度的影响最大,粘结层材料特性的影响较大,热氧化生成层的材料特性及基体的屈服极限对合理压入深度的影响不大.     

Cu-Zr-Ti块体非晶合金的形成及其力学性能

在Cu-Zr-Ti的三元合金系中发现了具有高非晶合金形成能力的Cu₆₀Zr_40-xTi_x(x=5%~27.5%,x为原子数分数)合金,采用铜模铸造法制备了块体非晶合金,其过冷液体温度区间为38~65?K.在该合金系中具有最高非晶形成能力的成分范围为Cu₆₀Zr_40-xTi_x(x=7.5%~12.5%),其非晶形成临界直径为5?mm,是Cu-Zr-Ti三元非晶合金中迄今为止非晶形成能力最高的合金.Cu₆₀Zr_40-xTix(x=7.5%~12.5%)块体非晶合金的杨氏模量、压缩断裂强度、压缩塑性应变和硬度分别为80~114?GPa,1?730~1?865?MPa,0.3%~1.5%和Hv 693~Hv 824,并随Ti含量的增加而提高.同时具有高非晶形成能力、高强度及显著塑性变形能力的铜基块体非晶合金的发现对非晶合金的基础研究和高性能结构材料的开发具有重要意义.     

丁羟推进剂粘合剂网络结构调控方法探讨

把扩链剂的使用作为调整丁羟推进剂粘合剂网络及其形态结构的一个重要手段。采用扩链剂、交联剂和真实固化参数(Rt)等综合的方法调控丁羟推进剂性能,可望比单纯控制名义固化参数(Ro)获得更好的力学性能及其稳定性。推导了丁羟推进剂粘合剂系统网络调整的通用计算公式和各种特定条件下的计算公式。     

Assessment of between-floor structural and topological properties on cognitive map development in multilevel built environments

The present study investigated cognitive map development in multilevel built environments. Three experiments were conducted in complex virtual buildings to examine the effects of five between-floor structural factors that may impede the accuracy of humans’ ability to build multilevel cognitive maps. Results from Experiments 1 and 2 (of three experiments) revealed that difficulties in developing multilevel cognitive maps are not solely caused by the z-axis offset, as is suggested in the literature, but are due to the factorial combination of a between-floor overlap and a z-axis offset. Results from Experiment 2 showed that this process becomes substantially more difficult when the reference directions between different floors have an angular offset from each other. Finally, results from Experiment 3 demonstrated that confusing between-floor heading shifts in aligned buildings did not make it reliably harder to build multilevel cognitive maps. The implications of these findings are discussed in terms of theories of mental representations in multilayered three-dimensional spaces, as well as for architectural design.     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

A review of friction stir joining of SiCp/Al composites

SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace, automotive industry and other fields. Due to the huge difference in performance between SiC particles and matrix alloys, traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites. Friction stir joining (friction stir welding), as a solid phase joining process, has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process. Although some progress has been made in recent years, there are still full of challenges. In this paper, the research status of friction stir joining of SiCp/Al composites in recent years is expatiated, including the weldability of SiCp/Al composites, the macrostructure and the microstructure of joints, mechanical properties of joints, and tool wear and monitoring. Furthermore, the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.     

温度参数下轴编C/C复合材料的超高温热结构性能分析

为了研究轴编碳/碳（C/C）复合材料的超高温热结构性能,开展了2800℃超高温载荷下复合材料的拉伸实验,表征了复合材料组分材料的高温失效形貌;提出了立方体单胞和正六棱柱单胞的温度周期性边界条件的算法和预测复合材料等效热结构参数的方法,在材料属性各向同性正六棱柱单胞模型上验证了方法的正确性;最后建立了轴编C/C复合材料的代表性体积单元,计算了复合材料随温度载荷变化下的等效热结构参数,与实验数据进行了对比分析。分析表明：开展的轴编C/C复合材料的超高温拉伸实验,可以得到复合材料在2800℃载荷下复合材料的等效刚度值,同时分析了轴向试件和径向试件的高温失效机理,径向试件的纤维束拉伸强度对复合材料的径向拉伸强度起到决定性的作用。在应用位移以及温度周期性边界条件的基础上,提出的方法可以得到随温度载荷变化下复合材料的等效热结构参数,得出复合材料在横向满足近似各向同性的特性,预测结果表明只改变温度参数下复合材料的等效热导率不会发生改变。提出的方法同样也适用于其他编织复合材料的热结构性能研究。     

三维五向编织复合材料的冲击压缩特性及破坏机制

利用分离式霍普金森压杆(split Hopkinson pressure bar,SHPB)实验系统和高速摄像技术对三维五向碳/环氧编织复合材料的动态压缩特性进行研究。通过对编织角为22.3°的试样分别进行沿纵向和横向方向的冲击压缩实验,得到材料在200~1200 s^-1应变率范围内的应力应变曲线,并结合高速摄像记录的动态压缩过程,对不同应变率下材料在高速变形下的渐进破坏规律进行分析。同时,综合试样的宏观破坏特征和微观断口形貌特征,进一步分析材料的破坏模式及破坏机理。结果表明:随着应变率的增加,材料在纵向和横向均具有一定的应变率强化效应,在横向方向的应变率强化效应更为显著;不同加载方向下材料的渐进破坏过程、应力应变曲线特征以及破坏方式均具有明显差异,且随着应变率的增加而发生改变。