固溶时效处理对高强高韧钛合金显微组织与力学性能的影响

对固溶时效处理后的高强高韧钛合金初生α相的体积分数、尺寸,次生α相的体积分数和α_s/β相界面密度等显微组织特征进行了定量表征和统计分析,探讨了随着固溶温度的变化,高强高韧钛合金显微组织与其力学性能间的相关性.结果表明:在α+β两相区固溶时效处理,随着固溶温度的升高,合金初生α相的体积分数降低,相尺寸先降低后略有升高,次生α相的体积分数升高,α_s/β相界面密度先升高后降低.初生α相的体积分数与伸长率、静力韧度和裂纹形成功正相关,α_s/β相界面密度与合金屈服强度成正相关.      

亚/超声速楔状流层流边界层速度与温度相似解及拟合解

利用相似变换获得了楔状流层流边界层无量纲流函数的3阶非线性常微分方程,用Runge-Kutta法求解微分方程获得了不同楔形角楔状流层流边界层无量纲速度随相似变量的变化曲线;推导了亚声速和超声速楔状流层流边界层无量纲温度关于相似变量的2阶线性齐次和非齐次微分方程,获得了温度分布的通解,恒壁温条件下亚声速楔状流和绝热壁面条件下超声速楔状流层流边界层无量纲温度解析解及指数函数形式的拟合解.以楔形角为0为例利用相似变换研究了超声速条件下气体压缩性及黏度随温度变化等因素对层流边界层速度与温度的影响,得出不可压缩常物性与可压缩变物性条件下无量纲速度相对误差绝对值小于9.8%的结论.研究表明:Pr越大贴近壁面处无量纲温度变化越剧烈;超声速条件下壁温低于绝热壁温时黏性耗散作用可以使层流边界层气体温度从壁面到主流间出现先升高后降低的变化.      

运输机超低空空投重物动力学分析与Ｈ∞鲁棒控制设计

运输机超低空空投重型货物是一个对控制精度要求较高的复杂技术过程。本文针对飞机-货物间约束力的理想特性,采用拉格朗日分析力学的第二类方程,建立了机-货两体系统的耦合动力学方程,比起牛顿矢量力学方法,受力分析和建模过程简洁方便。在定义飞机及货物状态变量的基础上,将上述方程组转化为状态空间描述。为了有效抵抗货物移动对运输机姿态的影响,基于现代鲁棒控制理论,设计了状态反馈H∞最优控制律。最后,对空投过程进行了无控和闭环控制两种条件下的数值仿真对比。结果显示,本文设计的H∞最优控制能有效抑制货物移动对运输机姿态的影响,改善了飞行品质,且控制量在工程允许的范围内,该控制律是有效的。     

基于闭环解析解的可重复使用运载器轨迹在线生成方法

The relationships between path constraints such as heating rate, dynamic pressure and aerodynamic load and velocity during entry flight are analyzed in  r-V  plane for an entry vehicle with mediate high lift to drag ratio. Through derivation and integration, a unified formula for path constraints is obtained in  r-V  plane. Based on the unified formula and several characteristics an analytical solution is obtained,and an online trajectory generation method is developed. In the method, the coupled longitudinal and lateral motion is considered, and can make the best use of flight capability and satisfy path constraints. Trajectory generation cases with different flight mission and downranges are tested. Simulation results demonstrate the capability and efficiency of the trajectory planning method in dealing with path constraints.     

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

Twaron纤维的新型化学活化方法

以傅瑞德-克拉夫茨(Friedel-Crafts)反应为基础,活化处理Twaron纤维的惰性表面。对经过活化处理的Twaron纤维进行了单丝拔出(SFP)、X射线衍射(XRD)、扫描电镜(SEM)、红外图谱(FTIR)、表面电子能谱(XPS),以及表面自由能等测试。测试结果显示,经过活化处理后,Twaron纤维表面因环氧基团的接枝而使表面自由能显著增加;纤维表面的结晶结构未发生显著改变,纤维的本体强度未降低;相对应的环氧树脂基复合材料的单丝拔出强度提高了约50%。     

ZnO透明导电薄膜制备及紫外辐照处理特性研究

ZnO作为一种典型的透明导电氧化物（Transparent conductive oxide,TCO）材料,具有同氧化铟锡(Indium tin oxide,ITO)相比拟的光电性能,其原料丰富、绿色环保、易于制备、生成成本低等优点使ZnO成为最有希望替代ITO的材料。本文以玻璃为衬底,利用量子点种子层作为缓冲层,采用传统水热方法制备了低成本ZnO透明导电薄膜,采用特殊的紫外光辐照工艺对薄膜进行后处理,探索薄膜生长参数和紫外光辐照处理工艺对其透光率和导电性的影响。结果表明,紫外辐照处理不影响薄膜的透光性能,而使材料的方块电阻降低3个数量级,数值从没处理时的1.5×105 Ω/□降低到 150 Ω/□,极大地提高了薄膜的电导率,为ZnO薄膜材料电导率的提高提供了一个简单高效的途径。     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

均匀化处理对TiAl 合金铸造组织的影响

研究了均匀化处理对两种含B的铸造TiAl合金铸造组织的影响。研究发现1 370℃/5 min/OQ+1150℃/6 h/AC均匀化热处理能有效消除B2相,将b稳定化元素固溶到基体中,实现成分均匀化;1 370℃/5 min/OQ+1 150℃/24 h/AC均匀化热处理后可使粗大的铸造片层组织分解转变为细晶近g组织,平均晶粒直径50mm。     

Fast Online Approximation for Hard Support Vector Regression and Its Application to Analytical Redundancy for Aeroengines

The hard support vector regression attracts little attention owing to the overfitting phenomenon. Recently, a fast offline method has been proposed to approximately train the hard support vector regression with the generation performance comparable to the soft support vector regression. Based on this achievement, this article advances a fast online approximation called the hard support vector regression (FOAHSVR for short). By adopting the greedy stagewise and iterative strategies, it is capable of online estimating parameters of complicated systems. In order to verify the effectiveness of the FOAHSVR, an FOAHSVR-based analytical redundancy for aeroengines is developed. Experiments on the sensor failure and drift evidence the viability and feasibility of the analytical redundancy for aeroengines together with its base-FOAHSVR. In addition, the FOAHSVR is anticipated to find applications in other scientific-technical fields.