薄壁曲面复合材料层合板成型工艺参数与形面精度影响规律

为了得到高形面精度复合材料层合板适用的成型工艺控制方法，本文针对典型的Φ500 mm直径曲面球冠结构复合材料层合板，设计了6组不同工艺参数的成型对比实验，分析出边缘效应、铺放方式、固化温度等参数对层合板固化变形量的影响规律。研究表明，增加碳纤维模量和降低预浸料单层厚度可提高层合板形面精度；层合板铺放尺寸超过直径的5%可降低边缘效应的影响；自动铺丝技术铺放质量一致性高，手工铺层可以制造出高形面精度的层合板，但相对发生概率低；降低层合板固化温度和降温速率能够有效地提高层合板的形面精度。实验结论对复合材料高精度成型具有一定的指导意义。     

Comprehensive performance review of BDS-3 after one-year official operation

On July 31, 2020, the third generation BeiDou Global Satellite Navigation System (BDS-3) was officially put into service. Here we first reviewed the development history of BDS-3, and described the status of BDS-3 constellation, satellite signals, and ground tracking network. Then we expounded the 10 innovations in which BDS-3 differs from the other global satellite navigation systems. In addition, the latest service performance status of BDS-3 was displayed from a comprehensive perspective. The performance of BDS-3 was analyzed and evaluated from five aspects: constellation performance, observation data quality, spatial signal performance, PNT (Positioning, Navigation, and Timing) service performance, and precision positioning application. We used 14 indices to conduct comprehensive assessment of the BDS-3 service performance. Finally, the main direction of the next development of BDS was prospected.     

卫星在轨推进剂补加量测量方法精度研究

卫星在轨推进剂补加量的精确测量技术是在轨补加任务的关键技术之一。本文结合型号攻关结果，提出2种在轨推进剂补加量测量方法数学模型，分别是压力-体积-温度(PVT)法和超声波流量计法。首先，PVT法是一种通过补加前后受体卫星贮箱剩余量反算补加量的间接测量方法，而超声波流量计法是利用超声波顺逆流相位差进行测量的直接测量方法;其次，在推进剂补加量测量模型的基础上，进一步通过取变分的手段提出2种模型的精度分析解析模型，解析的精度分析模型不仅可用于定性分析影响测量精度的因素，还可量化评价各个因素对测量精度的影响;最后，利用现有在研单机的精度水平及精度分析解析模型分析了2种方法的测量精度，验证了方法的有效性。     

北斗三号系统PPP-B2b信号定位服务模型及性能分析

给出了PPP-B2b信号定位的观测模型和随机模型，详细阐述了PPP-B2b增强改正模型和参数估计模型，并进行了静态和动态定位实验。结果表明：对于单系统，在30min的收敛时间内，北斗三号定位精度可以达到水平0.118m（静态）、0.176m（动态），高程0.208m（静态）、0.423m（动态）以内，GPS定位精度可以达到水平0.113m（静态）、0.163m（动态），高程0.206m（静态）、0.377m（动态）以内；对于北斗三号/GPS双系统，在20min的收敛时间内，定位精度可以达到水平0.092m（静态）、0.122m（动态），高程0.158m（静态）、0.312m（动态）以内。无论是收敛性还是定位精度，均能满足北斗三号精密单点定位服务指标的要求。     

EWIS支架装配变形及其承载分析

民用飞机EWIS系统支架遍布全机,在空间狭小的区域,考虑到装配和维修的要求,需采用单侧安装工艺,若支架装配时未固定好或操作不当,会导致支架承受安装力矩载荷,使支架结构产生塑性变形和残余应力,严重的会导致支架破坏。为了分析EWIS支架在安装力矩下的应力和变形情况,采用ABAQUS对典型标准支架进行有限元分析,考虑材料的非线性特性,得到了支架在不同安装力矩下的变形和应力情况,并对塑性变形后的支架继续承载进行了分析,对比分析支架塑性变形前后承载的应力,得出了变形对承载的影响。采用非线性有限元分析方法可对支架安装力矩的作用进行模拟,并计算结构产生塑性变形后承载的应力水平,为民用飞机EWIS支架的装配过程和塑性变形后的承载分析提供参考。     

Analysis on navigation accuracy of high orbit spacecraft based on BDS GEO and IGSO satellites

To make up for the insufficiency of earth-based TT&C systems, the use of GNSS technology for high-orbit spacecraft navigation and orbit determination has become a new technology. It is of great value to applying Geosynchronous Earth Orbit (GEO) and Inclined GeoStationary Orbit (IGSO) navigation satellites for supporting the navigation of high-orbit spacecraft since there are three different types of navigation satellites in BeiDou Navigation Satellite System (BDS): Medium Earth Orbit (MEO), GEO and IGSO. This paper conducts simulation experiments based on Two-Line Orbital Element (TLE) data to analyze and demonstrate the role of these satellites in the navigation of high-orbit spacecraft. Firstly, the spacecraft in GEO was used as the target satellite to conduct navigation experiments. Experiments show that for the spacecraft on the GEO orbit, after adding GEO and IGSO respectively on the basis of receiving MEO navigation satellite signals, the accuracies were improved by 7.22 % and 6.06 % respectively. When adding both GEO and IGSO navigation satellites at the same time, the accuracy can reach 16 m. In the second place, navigation and positioning experiments were carried out on three high elliptical orbit (HEO) satellites with different semimajor axis (32037.2 km, 42385.9 km, 67509.6 km). The experiments show that the number of visible satellites has been improved significantly after adding GEO and IGSO navigation satellites at the same time. The visible satellites in these three orbits were improved by 32.84 %, 41.12 % and 37.68 %, respectively compared with only observing MEO satellites.The RMS values of the navigation positioning errors of these three orbits are 25.59 m, 87.58 m and 712.48 m, respectively.     

电化学加工机器人动态性能设计与优化研究

工业机器人工作空间大、姿态灵活、可配置性高，且成本低，广泛应用于搬运、装配、喷涂和焊接等多个领域。但由于机器人末端轨迹精度不高，低速波动大，在电化学加工领域的应用很少。根据电化学加工低速、高轨迹精度特点，提出采用象限法设定电化学加工机器人工作区域，建立电化学加工机器人动力学优化函数，采用第三代非支配遗传算法NSGA-Ⅲ求解各设计参数最优Pareto解集，通过仿真和实验进行了动态性能测试验证。结果表明在设定工作区域内，电化学加工机器人直线轨迹精度可达0.073 mm，圆弧轨迹精度可达0.145 mm，低速工况下轨迹精度相比传统工业机器人提高近10倍。     

力矩输出能力最优化混合执行机构操纵律设计

当航天器执行高动态敏捷机动或者姿态动态跟踪控制等任务时，常使用控制力矩陀螺（control moment gyroscope，简称CMG）和飞轮（reaction wheel，简称RW）构成的混合执行机构来提供大力矩。提出了基于力矩输出能力最优化的混合执行机构操纵律，从几何角度出发，给出了力矩输出能力最优的CMG框架角速度和RW角加速度，通过引入参数，并讨论参数的设置的最优，使得框架转速误差和输出力矩误差的混合二次型达到最小，保证了混合执行机构在输出力矩误差最小的情况下，力矩输出能力最优。以金字塔构型的CMG集群和正交的RW集群构成的混合执行机构为例，对基于力矩输出能力最优化的混合执行机构操纵律进行合理化分析，证明了引入参数的作用，并且证明了混合执行机构不存在CMG奇异情况。仿真结果表明，基于力矩输出能力最优化的混合执行机构操纵律解决了CMG奇异的问题并使得RW不陷入饱和，输出力矩误差较小，输出力矩能力强，能够应用于航天器大角度机动任务。     

Influence and experiment of cable-net manufacturing errors on surface accuracy of mesh reflector antennas

Cable-net structures are of substantial importance in the construction of large mesh reflector antennas. Owing to the inevitable errors in their manufacturing process, the reflector surface accuracy deteriorates. This study makes a comprehensive investigation of random manufacturing errors during constructing the mesh reflector antennas, and analyze its influence on reflector surface accuracy. Firstly, the sensitivity of reflector surface accuracy with respect to the random errors of the unstressed cable length is mathematically deducted. Secondly, a non-button connecting method is proposed and analyzed to reduce manufacturing errors. Thirdly, two physical experiment models based on 2.62-meter mesh reflector antenna are made. Finally, numerical examples and experimental tests are given to demonstrate the effectiveness of the proposed method. Compared with the traditional method, the proposed method can effectively reduce the influence of the manufacturing errors on the reflector surface accuracy. Moreover, the reduction in the sizes of the nodes also reduces the risk of entanglement of the mesh reflector antenna during the deployment process, and thereby improves the deployment reliability.     

基于双回路控制的电动负载模拟器研究

电动舵机负载模拟器可在实验条件下模拟飞行器飞行过程中舵机受到的空气动力铰链力矩,是半实物仿真的重要设备。在介绍电动负载模拟器研究进展并指出目前伺服系统研究所面临的难题的基础上,以改善系统动态频响为目标,设计基于双回路电机的加载方案并建立双回路系统的数学模型;通过系统仿真,分析系统输出力矩对指令力矩的跟踪能力,验证数学模型的准确性。结果表明:双回路方案有效地抑制了系统多余力,其工作频带在舵机扰动的情况下仍可达35 Hz,为电动负载模拟器提供了一种频带更高、匹配性更好的实现方案。