磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

W波段UAV MISAR实时成像运动补偿方法

建立了实时成像正侧视合成孔径雷达(SAR)运动误差模型,采用了一种基于惯导和相位梯度自聚焦(PGA)运动误差估计的中心波束平面运动补偿算法。该算法对回波包络和相位进行分开补偿,利用惯导数据把带有运动误差的回波包络拉直,再利用相位梯度自聚焦算法对回波进行相位误差估计并补偿。针对实时成像的时间少、运算量大、运算资源受限等特点,该算法取消了距离徙动校正的步骤,将运动误差矢量在斜距平面投影并完成包络校正和相位误差估计。该方法运算量小,同时能满足分辨率要求。仿真结果表明:该方法能够得到质量较高的SAR图像。     

永磁约束电子束轨迹实验研究

通过设计并运用一种直流电子束轨迹简易测量方法,开展了永磁约束电子束轨迹实验研究,得到了永磁铁环对60~80 ke V电子束约束作用的实验数据。结果表明:该测量方法方便有效,结果较为准确;永磁铁对电子束聚焦作用明显,并呈现出一定的规律性。对永磁铁约束电子束研究工作奠定了基础。     

非线性能量阱对飞轮振动抑制效果的实验研究

利用薄片金属梁作为非线性刚度元件，构建一种非线性能量阱。为了验证非线性能量阱对飞轮振动特性的抑制效果，搭建地面飞轮测试系统。分别采用力锤敲击和飞轮以恒定转速运行的方法施加不同载荷，对安装非线性能量阱前后测试系统各典型位置的振动响应进行对比研究。利用实测数据，采用傅里叶变换方法将动态响应信息分别在时间域和频率域内展开。研究表明：力锤敲击产生的冲击载荷和飞轮以恒定转速运行产生的稳态载荷均可以激发非线性能量阱定向能量传输；受非线性能量阱的影响，柔性支架设备安装面和飞轮安装面振动响应得到有效抑制。但是，由于非线性能量阱阻尼和吸振子质量较小，不同程度削弱了其振动抑制效果。     

Experimental investigation on silica dust lofting due to charging within micro-cavities and surface electric field in the vacuum chamber

The charged dust particles can be mobilized electrostatically by the repulsion between the adjacent grains and the surface electric field due to the incoming electron current and the charge accumulation within the micro-cavities. In this study, the experimental results of the initial vertical launching velocities and the maximum dust heights are compared with the estimated values for the lofted spherical dust grains by the patch surface charging equations. Silica particles with the sizes between <6 and 45?µm in radius are loaded on a graphite plate, and they are exposed to the electron beam with 450?eV energy under 4?×?10^?3?Pa vacuum chamber pressure. During the first set of the experiments, the dust samples are tested without an initial compression process and an additional horizontal electric field. Second, the dust samples are compressed by two different weights in order to increase the packing density under approximately 780.7?Pa and 3780?Pa. Finally, the dust grains are placed between the two parallel aluminum plates to apply approximately 2000?V/m and 4800?V/m horizontal electric field. A high-speed camera is used to record the transportation of the dust grains together with a microscopic telescope, and the results point out that the patch surface dust-charging model estimations are in agreement with the first experiments. On the other hand, the dust particles from the compressed samples are lofted with higher velocities than the estimations, and the number of the dust lofting observations decreases significantly, which demonstrates the importance of the micro-cavities and the increased charging requirement to overcome the contact forces. When the horizontal electric field is present, the initial vertical launching velocities are measured to be lower than the other experiments, which can be attributed to the decreased charging requirement for the dust lofting as a result of inter-particle collisions and rolling motion. According to the experimental results, the electrostatic dust transportation can be controlled not only by the ambient plasma and the solar irradiation on the airless planetary bodies, but also by the surface properties such as the contact surfaces between the dust grains, the number of the micro-cavities related to the packing density, and the presence of the horizontal electric field contributing to the external forces by other particle motions.     

高能电子辐照下介质-导体相间结构深层充电特性研究

为研究影响介质-导体相间结构深层充电特性的内在因素,设计了不同构型的试验样品,利用90Sr放射源模拟空间高能电子环境对样品进行深层充电辐照试验,测量了充电电位的差异。并借助深层充电三维仿真软件计算介质-导体相间结构在不同几何构型情况下的深层充电电位、电场分布。试验和仿真结果表明,介质最高表面电位以及介质内部最大电场均与介质宽度和高度呈正相关。其他条件不变时,介质越宽,或越高于导体表面,发生放电的风险就越高。在介质与导体侧面存在微小缝隙情况下,介质内最大电场显著增强,易发生内部击穿。而在介质与导体之间的真空间隙内,电场很容易超过击穿阈值,放电风险很大。航天工程应用中为降低此种结构深层充放电的风险,在满足绝缘性能及其他要求的前提下应尽量减小介质的宽度,降低介质与导体间的高度差,并确保介质与导体侧面接触良好。     

航空用铝合金超微结构实验表征

为了使铝合金更好的服役于航空领域,就有必要对其微观结构进行实验表征,从而可以在铝合金微观结构和宏观性能之间搭建桥梁,最终优化铝合金的综合性能。本文介绍了航空用2xxx,6xxx和7xxx系铝合金发展历程以及时效析出过程中的微观结构演变,如Al-Cu合金GP区、Al-Cu-Mg合金GPB区等重要物相的结构特征,以及AlCu-Mg合金S相析出行为等都已得到了透彻的研究;阐述了透射电镜、扫描透射电镜、三维原子探针等技术的结合在Al-Cu-Mg-Ag合金Ω相、Al-Mg-Si-Cu合金β″相的晶体结构及界面结构以及铝合金晶间腐蚀机理等研究上的应用;本小组实现了复杂选区电子衍射谱的快速模拟及标定,并基于会聚束电子衍射实现了对析出相体积分数的精确测量;最后指出,高分辨透射电镜原位加热研究及透射电镜原位力学测试等新技术手段的应用,对深层次研究铝合金相变规律、变形行为具有跨时代意义。     

The geomagnetic solar flare effect identified by SIIG as an indicator of a solar flare observed by GOES satellites

This paper studies the efficiency of geomagnetic solar flare effects (gsfe) in X solar flare detection; so during the period 1999–2007 a comparison between solar flare (sf) observed by satellites of the Geostationary Operational Environmental Satellite (GOES) programme and gsfe published by the Service International des Indices Geomagnetiques (SIIG) is made.     

激光器性能综合测试设备研制

介绍了激光器的主要性能指标,根据实际需要进行了激光性能测试设备的研究,提出了一种周全的激光性能测试设备研制方案,对该设备的结构设计、光路设计、以及测试方法作了详尽论述。设备中利用两对相互垂直的P分光镜和S分光镜以补偿偏振光在45°面上透反射率不同而造成的测量误差,进一步保证了激光能量测试的准确性。误差分析结果表明该设备满足实际应用中对激光器性能的测试要求。