焊后热处理对高温运行10CrMo910钢管接头持久寿命的影响

本文通过１０ＣｒＭｏ９１０钢大口径厚壁管道高温模拟试验证实，焊后热处理是一个短时超高温运行过程，它使１０ＣｒＭｏ９１０钢管接头组织提前老化，显著降低了接头的持久寿命。试验结果表明，传统的焊后热处理工序应当取消。     

模拟地球同步轨道辐照环境对光学太阳反射镜性能的影响

研究了模拟地球同步轨道辐照环境对卫星用温控涂层-光学太阳反射镜(OSR)性能的影响。对所研制的两类OSR 片进行的辐照试验项目有,真空紫外辐照、低能电子和两种能量的质子辐照。此外还进行了等离子体环境条件下的表面充/放电效应试验。经过相当于安装在地球同步轨道卫星南北极位置处,在空间七年所受到的电子、质子和紫外辐照总剂量的辐照后,导电型OSR 的太阳光谱吸收率α_s 由0.068增加到0.078,法向发射率ε_n 由0.83降低到0.72;而非导电型OSR的α_s 由0.066增加到0.085,ε_n 由0.82降低到0.76。表面充/放电试验的结果表明:导电型OSR 的充电电位仅在15～40V 之间,而非导电型OSR 的充电电位则可高达13kV。因此导电型OSR能有效地控制表面的充/放电现象。     

微重力场中对流—辐射—传质系统的地面模拟技术

研究了微重力条件下对流－辐射－传质稳态系统的地面相似模拟技术，进一步发 温度－材料综合保护技术。通过采取补偿热流，调整壁面热流密度分布的方法，保持了原型与尺寸适当缩小后的模型的Ｎｕ数，Ｓｈ数，材料，温度，湿度不变，从而实现模型与原型流动，换热和传质相似。     

防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

热沉温度场仿真研究

为了确定热沉温度场控制方法，建立了KM6热沉正常运行状态的数学模型，在MATRIX仿真平台上构造了仿真模型并求解，确定了KM6热沉温度场的动态特性和等价模型，并对热沉的设计提出了若干建议。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用，同时还将与火星表面航天器发生对流换热。热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响，从而确定主要的控温途径。在调研火星表面辐射、大气等热环境的基础上，从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响。器表辐射传热系数随光学属性和温度的变化范围为0.3～1.4W/(m2·℃)，对流传热系数随风速变化为0.2～1.5W/(m2·℃)，器内导热传热系数可控制在0.25W/(m2·℃)以下。结果表明，太阳辐射较火星表面和天空辐射而言是主要外热源，航天器表面的辐射和对流换热为两条并联换热途径，两者均可成为主要换热途径，器内导热传热是控制航天器内外隔热的主要可控因素。