边界层厚度对腔体气动声学特性影响数值模拟

为了研究来流边界层厚度对开式腔体气动声学特性的影响,基于分离涡模拟方法,计算了来流马赫数为2.0条件下,不同来流边界层厚度与腔体深度比时,长深比为5.88的腔体流动特性,得到了该腔体声压级的频谱特性.计算结果表明:随着来流边界层厚度增加,形成的剪切层稳定性增强,失稳后上下摆动幅度减少,失稳生成的大尺度涡与超声速主流的相互作用减弱,使得大尺度涡发展到腔体后缘时所具有的平动动能和转动动能降低.大尺度涡撞击腔体后缘在腔体内形成的气动噪声的声压级降低,最大减小幅度达7.5dB.同时各阶模态的频率也发生偏移,偏移值在100Hz左右.基于新的假设重新推导了Rossiter公式,明确了经验常数的物理意义,并以此解释了频率偏移现象.      

基于涡流发生器的风洞侧壁附面层控制

为降低风洞侧壁附面层对半模型数据的影响,在前期数值模拟的基础上,研制了一种适用于2.4m跨声速风洞半模型试验段侧壁的梯形涡流发生器,并进行了试验验证.结果表明:加装涡流发生器效果明显,亚声速范围内能够使附面层厚度降低20%~30%,对主气流均匀性影响可忽略;加装后半模型零升阻力系数降低,升力线斜率增大,压力中心向机身移动,体现了明显的附面层减薄效果,证明所研制的涡流发生器可应用于亚声速半模型试验中.      

平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

基于疲劳-蠕变载荷等效转换的涡轮盘载荷谱编制及寿命预测

针对雨流计数法在峰谷值提取时进行等值压缩,忽略保载时间的问题进行了改进,提出了一种基于损伤曲线的疲劳-蠕变载荷等效转换方法。利用非线性疲劳损伤累积函数和损伤等效原则,建立了不同应力水平、不同保载时间下疲劳-蠕变载荷与疲劳载荷之间的等效换算模型。利用涡轮盘材料试验数据,计算了不同循环加载条件下的等效换算比,得到了其随保载时间的变化规律。利用改进的雨流计数法,编制了航空发动机高压涡轮盘载荷谱,并将其与寿命-时间分数预测法相结合,得到了涡轮盘剩余寿命。结果表明,改进的雨流计数法综合考虑了疲劳-蠕变耦合损伤对涡轮盘寿命造成的影响,相比于传统雨流计数法,寿命预测误差降低了15.02%,验证了该方法的有效性。     

多功能水冷壁排管爬壁机器人的研制

介绍了一种新研制开发的永磁吸附式双履带结构爬壁机器人，主要应用于火力发电站的大型排管锅炉中的水冷壁排管壁面的清扫和检测，并能够在检测到壁面厚度小于预置的极限值处发出报警信号、打标记，具有较高的推广应用价值。文中阐述了该机器人的结构、磁路的优化设计、自动测厚、打标系统和控制系统的研制。目前，该机器人已经经过多次现场试验。各项指标均已达到设计要求。     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

水平表面气流剪切作用下的水膜厚度

飞机结冰表面上的液态水受气流吹拂作用会发生向后溢流,从而影响结冰区域范围及防冰系统设计;为了获得水膜流动规律,对水平平板表面上气流剪切驱动的水膜流动进行了实验测量和建模分析。通过水膜流动风洞试验台产生高速气流驱动水膜的流动,使用色散共焦位移计测量同一位置的水膜在不同时刻的厚度变化,结果表明气-液界面由底层薄水膜和多种尺度的波动组成,具有变化速度快随机性强的特点。通过水膜厚度随气流速度及水膜雷诺数的变化规律,发现平均水膜厚度与两者均呈现出单调非线性的依赖关系。基于薄水膜流动理论和平均水膜厚度实验结果,提出了高速气流剪切作用下的气-液波动界面剪切因子计算式,适用于风速17.8~52.2m/s,水膜雷诺数26~128之间的平板水膜流动计算。     

EB-PVD制备箔材的厚度均匀性研究

从真空蒸镀中使用的小平面蒸发源理论出发,针对电子束物理气相沉积中为改善箔材厚度分布所须旋转大基板进行蒸镀的情况,建立了该过程的数学模型;并利用该模型对不同的坩埚位置所沉积的箔材厚度进行了定性分析,从而实现了对坩埚与基板相对位置的优化,使基板上沉积的箔材厚度分布可以达到最均匀的状态.最后通过K值的提出使理论和实际箔材厚度的结果趋于一致,即证明所建立的数学模型是合理的.     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.