凹坑型硬物损伤对TC4材料疲劳强度的影响

针对风扇/压气机叶片中叶盆/叶背遭受的硬物损伤(FOD)凹坑型损伤,进行了不同冲击角度下模拟FOD试验、损伤特征与应力集中分析,开展了冲击后不处理和冲击后去残余应力退火试样的高循环疲劳试验研究和疲劳强度的预测。结果表明:损伤深度和应力集中系数均随着冲击角度的增加而变大,损伤深度范围为0.1~0.5mm,应力集中系数范围为1.3~1.7。不同冲击角度条件下,凹坑型损伤试样疲劳强度相对光滑试样下降程度在50%~70%范围内,与应力集中系数并不是呈单调下降关系,最危险冲击角为60°。去残余应力退火后凹坑型损伤试样的高循环疲劳（HCF）性能有所提高,表明残余应力的影响程度不容忽略。去残余应力试样的HCF性能并不是随应力集中系数的增大而下降,验证了微结构损伤的影响,说明损伤深度作为制定可用极限或维修极限的唯一参量具有一定的局限性。对凹坑型损伤试样的疲劳强度的预测误差在±20%以内。      

TC4钛合金惯性摩擦焊接过程的数值模拟

文摘基于ABAQUS有限元分析软件,建立了TC4钛合金的惯性摩擦焊(IFW)焊接过程的二维轴对称模型,通过确立Johnson-Cook损伤模型以及ALE技术对TC4钛合金的惯性摩擦焊焊接过程进行了热力耦合分析,发现TC4惯性摩擦焊在0.2 s内温度升高到200~300℃,0.5 s左右温度升高到1 100~1 200℃之后温度升高趋于平缓,到达峰值后温度缓慢下降,焊接完成。轴向缩短量在0.6 s内非常小,温度达1 100~1 200℃(0.6~1.2 s)轴向缩短量增长十分快并基本达到峰值,1.2~1.4 s由于粘结作用温度不再升高轴向缩短量增加缓慢,1.4 s后焊接基本完成轴向缩短量不再增加。初始阶段轴向应力基本没有变化,随着温度升高(0.2~0.5 s)压应力在中心区域增大,0.5~1.2 s内边缘形成拉应力,中心区域应力集中愈发明显,1.2 s后拉应力明显增加。而径向应力随着温度的升高中心应力明显高于外侧并使金属向两侧流动。这就可以得出飞边形成主要是因为高温、轴向应力以及径向应力共同复杂作用而形成的结果。模拟结果基本与实际相符,对提高惯性摩擦焊焊接质量提供了重要的参考作用。     

Variation of hmF2 and NmF2 deduced from DPS-4 over Multan (Pakistan) and their comparisons with IRI-2012 & IRI-2016 during the deep solar minimum between cycles 23 & 24

We report the results of ionospheric measurements from DPS-4 installed at Multan (Geog coord. 30.18°N, 71.48°E, dip 47.4°). The variations in F2-layer maximum electron density NmF2 and its peak height hmF2 are studied during the deep solar minimum between cycles 23 & 24 i.e 2008–2009 with comparisons conducted with the International Reference Ionosphere (IRI) versions 2012 & 2016. We find that the hmF2 observations peak around the pre-sunrise and sunrise hours depending on the month. Seasonally, the daytime variation of NmF2 is higher in the Equinox and Summer, while daytime hmF2 are slightly higher in the Equinox and Winter. High values of hmF2 around midnight are caused by an increase of upward drifts produced by meridional winds. The ionosphere over Multan, which lies at the verge of low and mid latitude, is affected by both $E\times B$ drifts and thermospheric winds as evident from mid-night peaks and near-sunrise dips in hmF2. The results of the comparison of the observed NmF2 and hmF2 for the year 2008–2009 with the IRI-2012 (both NmF2 and hmF2) and IRI-2016 (only hmF2) estimates indicate that for NmF2, IRI-2012 with Consultative Committee International Radio (CCIR) option produces values in better agreement with observed data. Whereas, for hmF2, IRI-2016 with both International Union of Radio Science (URSI) and CCIR SHU-2015 options, predicts well for nighttime hours throughout the year. However, the IRI-2012 with CCIR option produces better agreement with data during daytime hours. Furthermore, IRI-2012 with CCIR option gives better results during Equinox months, whereas, IRI-2016 with both URSI and CCIR SHU-2015 options predict well for Winter and Summer.     

LOX/LCH_4变推力发动机技术初步研究

对国内外变推力发动机和LOX/LCH4发动机的研究进展进行了总结,在此基础上,提出了一种LOX/LCH4变推力发动机系统方案。在深入分析的基础上,对此方案进行了功率平衡和推力室传热计算,结果表明该系统方案完全能够实现10:1推力变比。LOX/LCH4变推力发动机可以广泛应用于多种运载器和航天器中,对我国探月及后续的载人登月工程均可以提供技术支持,对LOX/LCH4发动机的技术发展和未来的载人登陆火星等任务都具有深远影响。     

中国南京地区L波段电离层闪烁初步统计分析

利用南京地区2008年11月至2009年10月电离层闪烁监测数据, 统计分析了该地区一年间L波段电离层幅度闪烁发生率的逐日变化、逐月变化、地方时变化和空间分布等特征. 统计结果表明, 在此期间, 南京地区L波段电离层幅度闪烁活动比较平静, 主要以0.14<0.2的闪烁为主, S₄>0.2的闪烁很少发生.不同强度幅度闪烁表现出一致的时间变化和空间分布特征, 2008年11月为最小,2009年6月、8至10月闪烁发生率都有明显的增强, 在10月达到最大, 在8月和10月的S₄>0.2的闪烁主要出现于正午到日落前这段时间; 对于闪烁的空间分布, 单站一年数据统计显示, 测站北向闪烁的发生频率高于南向, 但该统计结果需要更多的数据样本进行进一步的验证.      

基于TCAD和Geant 4的SRAM单粒子效应评估

基于Geant4和TCAD (Technology-Computer Aided-Design)建立了一套评估静态存储器(SRAM)单粒子效应的方法. 该方法利用TCAD软件模拟半导体存储单元对粒子能量沉积的响应, 获得SRAM的重离子单粒子翻转截面, 并应用蒙特卡罗工具包Geant 4计算质子与硅材料的核反应以及次级粒子在灵敏体积内的能量沉积, 进而获得质子的单粒子翻转率. 利用该方法, 计算了TSMC 0.18 μm未加固SRAM的重离子和质子翻转率, 通过与同工艺SRAM的重离子实验结果进行比较, 初步验证了该方法的有效性. 该方法不依赖于地面模拟实验, 可以用来评估处于设计阶段的抗辐射加固器件.      

反向蒙特卡罗方法在卫星辐射分析中的研究与应用

反向蒙特卡罗方法(AMC/RMC)是Geant4中一个强有力的偏置技术. 粒子产生于包含灵敏体的反向界面并在几何体中被反向追踪直至外界面或溢出能量阈值, 其计算时间只集中于对结果有贡献的粒子径迹. 与正向蒙特卡罗方法(FMC)相比, RMC更高效, 特别是当灵敏体远小于几何体其他部分和外界面时, 其优势更明显. 通过RMC与FMC的比较, 验证了RMC应用于卫星辐射剂量分析的准确性. RMC与SHIELDOSE2和SSAT的比较说明了RMC是高精度卫星辐射剂量的优选方法.      

热处理对激光增材制造TC4合金耐蚀性及室温压缩蠕变性能的影响

随着钛合金装备在航空、航天、航海等领域的使用逐渐增多,其服役环境日益严苛,对构件材料的抗腐蚀性能及室温应力蠕变性能提出了更高要求。针对钛合金耐蚀性及抗压缩蠕变的性能,分析了激光增材制造TC4合金不同热处理状态试样电化学及室温压缩蠕变性能,并结合蠕变曲线修正了蠕变第Ⅰ阶段本构方程的参数。结果表明,双重退火处理会显著减小增材制造TC4钛合金中α板条长径比与尺寸,而固溶时效可使α板条长径比增大、尺寸减小,导致了材料耐蚀性、屈服极限以及抗压缩蠕变性能的变化。沉积态合金经过固溶时效后自腐蚀电流降低64.92%,稳态蠕变应变率降低46.31%,蠕变应变降低50%。而经过双重退火后合金自腐蚀电流降低26.14%,稳态蠕变应变率提升111.20%,蠕变应变提升48.68%。相比于铸锻工艺制备TC4合金蠕变本构方程,修正后的拟合系数与蠕变曲线吻合度更高。     

Influence of longitudinal-torsional ultrasonic-assisted vibration on micro-hole drilling Ti-6Al-4V

As Ti-6Al-4V is a typical hard to machine material, especially in micro drilling aviation parts, chip breaking difficulty is of increasing interest to explore its further development. In this study, Longitudinal-Torsional Ultrasonic Assisted Drilling (LTUAD) was employed to machine Ti-6Al-4V, and its feasibility was evaluated by comparing with Conventional Drilling (CD). By combining periodical characteristics and vibration models (the separated or the unseparated ultrasonic elliptical vibration), the influence of ultrasonic frequency on the intersection characteristics of trajectories were analyzed. And the intersection characteristics were divided into four categories: even periodicity, odd periodicity, non-odd and even periodicity and composite periodicity, indicating different capability for chip breaking. By applying the longitudinal-torsional compound vibration horn, the micro-hole drilling experiment was carried out on machining center. The chip morphology, the thrust force, and the burr height were discussed. Experimental results showed that the morphology of chips presented as smaller and more fragmentary ones in LTUAD compared with continuous helical conical ones and fold-shaped ones in CD. Compared with CD, the average values of the thrust force in LTUAD reduced by 1.98% to 24.9%. According to the burr around the hole exit in both LTUAD and CD, the height of the latter was greatly affected by the drilling parameters. And the burr around the exit of the hole were distributed rather evenly with smaller extension in LTUAD. Consequently, the LTUAD employed in micro-hole drilling was effective.     

一种空间极低温吸附制冷机的设计与实现

针对极低温吸附制冷技术的热沉制冷系统,系统分析了极低温吸附制冷的特性,研究了热沉温度对极低温吸附制冷性能的影响,研制了一台极低温吸附制冷机样机,工质气体为氦4,在1.5W@4.2K G-M制冷机基础上实现了50μW@0.8K的制冷性能,验证了基于机械制冷系统的更高热沉温度技术的可行性,这一成果为深空探测和载人空间站相关研究提供了技术支撑。