碳纤维用PAN原丝超声波水洗新技术

为降低PAN原丝中的DMSO(二甲基亚砜)残留量,减少其对原丝的拉伸、预氧化处理等过程的不利影响而造成的碳纤维的结构缺陷、强度降低,将超声波水洗技术应用到PAN原丝水洗工艺中.结果证明,新方法明显提高了水洗效果,能够快速有效地降低原丝中DMSO残留量.     

曲面不锈钢/微晶玻璃层状复合材料的设计制备

设计制备了与1Cr17和0Cr18Ni9不锈钢匹配的CaO-Al2O3-SiO2(CAS)系和BaO-Al2O3-SiO2(BAS)系微晶玻璃,研究了微晶玻璃的各项理化性能。利用流延法制备微晶玻璃生带,以此制备符合曲面不锈钢/微晶玻璃层状复合材料,并对复合材料相关性能进行测试。结果表明,所设计制备的玻璃经850℃、30min热处理后可形成线胀系数与对应不锈钢匹配的微晶玻璃,且具有适宜弯曲强度和较低介电常数、介质损耗;由此制备的曲面不锈钢/微晶玻璃层状复合材料具有良好的绝缘性能、结合强度和抗热冲击性能。     

316不锈钢/WC-Co涂层在锌液中的腐蚀

研究了经高速火焰喷涂(HVOF)的316不锈钢WC-Co涂层在锌液中的腐蚀行为,包括腐蚀速度、界面组织形貌和成分的变化.结果表明,WC-Co涂层在锌液中的腐蚀表现为沿裂纹的腐蚀.涂层中的缺陷造成裂纹源,在锌液和热喷涂过程留下的残余热应力的作用下,发生裂纹扩展,形成沿裂纹的腐蚀.铬和铝的扩散能力都比锌强,在产生裂纹的初期,铬和铝将优先锌扩散到裂纹中.如果适当改善喷涂工艺,增加涂层的致密度,可以延长涂层的使用寿命.     

基于Euler／N—S方程的跨音速非线性静气动弹性问题研究

在C-H网格的基础上,采用Jameson的中心差分有限体积法求解Euler/N-S方程,采用结构影响系数法计算结构的弹性变形,用三角元面积加权法和常体积转换法(CVT)实现流固耦合,计算了弹性后掠机翼在跨音速状态的静气动弹性问题     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

MOCVI制备Nextel 720/SiO2复合材

研究了MOCVI(MetalOrganicChemicalVaporInfiltration)方法制备Nextel720/SiO     

计算机辅助计划管理和决策总体设计

 介绍一种新机研制计划管理和决策支持系统的总体设计方案及其实现的具体措施。详细介绍了几个主要模块的设计思想。     

一种新颖的光回波损耗测量方法

介绍了一种新颖的光回波损耗测量方法.使用该方法测量光纤器件的回波损耗不但具有小的测量不确定度,而且有效地解决了光回波损耗参数的量值溯源问题.     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。