广州地磁Z分量日变幅的谱特征

利用1972—1993年广州地磁资料，分析了Z分量日变幅的年平均、年变化和半年变化等低频成分的逐年变化，以及小于60天的短周期变化特征．同时对1972—1993年的F10.7日均值进行了谱分析．结果指出，广州地磁Z分量日变幅的年平均与太阳活动指数F10．7的年平均存在良好的线性相关；具有幅度大约5nT夏季极大的年变化，与太阳活动没有明显相关，是一种季节效应；存在春秋分极大的半年变化，幅度与太阳活动有关，高年的幅度明显大于低年；具有明显的与太阳自转相关的27天左右的变化和明显的与行星波有关的接近16日、10日、5日、2日等短周期变化．广州地磁Z分量日变幅的这些谱特征，有助于更深入地了解中低层大气对电离层影响的物理机制．     

线性特征系统的标准形

本文在可控、可观测的条件下,建立了线性特征系统的标准形,并说明了系统结构参数d_1在建立标准形过程中的作用。对d_1=0的情况,通过上述标准形讨论了矩阵A的生成元所具有的独特性质。     

一个新的蠕变寿命估算公式的推出

本文从一些经典公式出发,推导出新的寿命公式。另外,通过引入蠕变损伤特征参量的概念还导出类似的另一个蠕变寿命估算公式。所推导出两个公式在16MnR材料中得到较为成功的应用。     

轴对称跨音速流中无激波超音速区的设计

本文直接从音速线出发计算了一个旋成体跨音速绕流超音速泡中的特征线网。提出了从音速线开拓到一条超音速线的方法,计算了无旋轴对称流的特征线网,发现其特点是不能跨越对称轴线,并对其原因作了初步的讨论。本文的计算结果可应用于物面修形。     

用非线性模型分析气动液阀的启动特性

对气动液阀的启动过程建立了非线性数学模型,分析了尺寸参数和推进剂进、出口压力对该阀的启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下,适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径,降低推进剂进口和出口的压力有利于提高该阀的响应能力。     

多孔层板换热特性实验研究

本实验选取了一种典型结构的多孔层板作为研究对象 ,进行了换热特性实验研究。研究了改变冷热气流吹风比对该型层板冷却效果的影响。另外 ,对该型多孔层板的冷却效果沿中轴线顺气流方向的变化规律也作了深入的研究。并给出了层板局部 N ux 和冷却效果 E关于局部 Rex 及冷热气流吹风比 M的数学拟合表达式。     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

CO2脉冲激光与气体相互作用实验

实验研究采用波长为10.6μm的CO2脉冲激光器,N2,He,CO2等三种纯净气体及上述气体的相互混合气作为推进工质时,通过实验舱内的冲击摆装置对抛物形光船获得的冲量耦合系数Cm进行了测量。实验发现气体工质的获得的冲量耦合系数Cm随气压增高而增大,通常气体工质的分子量越大,冲量耦合系数Cm越大;在低气压条件下,分子量较大的气体所占的比例越高,混合气获得的冲量耦合系数Cm越高;在高气压条件下,混合气体工质获得的冲量耦合系数与混合气体的种类及比例密切相关。     

流量定位喷注器的静态与瞬态特性

本文分析了流量定位喷注器的工作原理及静态与瞬态特性,给出了实现等压降工作特性的基本准则.