电离层拟合方法及路径参数量化分析

针对多层电离层,采用反抛物层作为连接层来描述电离层之间区域的电子密度分布.以电子密度和其相对于高度的一阶偏导数连续为依据,拟合出连接层的临界频率、半厚度和底高等电离层参数.将电离层的准抛物模型和连接层的反抛物模型中计算出来的等离子频率代入Appleton-Hartree公式和Snell定理,结合射线的几何结构完成多层电离层中的射线追踪,同时计算群路径、相路径和传输距离这3种重要的路径参数.分析当给定频率时,路径参数与入射角之间的关系,群路径、相路径与传输距离之间的关系,频率对路径参数之间变化关系的影响;同时分析了给定入射角时,路径参数与射线工作频率之间关系和入射角对于路径参数之间变化关系的影响.     

Bolt insertion damage and mechanical behaviors investigation of CFRP/CFRP interference fit bolted joints

Interference fit has advantages in improving fatigue behaviors of composite bolted joints; however, interference fit bolt insertion tends to cause damages in laminates weakening joint mechanical properties. Therefore, an experimental study was conducted to investigate bolt insertion damages of Carbon Fiber Reinforced Polymer (CFRP)/CFRP interference fit bolted joints. Mechanical behaviors of joints were also evaluated experimentally under both quasi-static loads and cyclic loads. Scanning Electron Microscope (SEM) and high-resolution X-ray micro-CT scan were used to examine micro damages in laminates. Damage and failure behaviors of joints were characterized. The results demonstrated that the hole entrance in upper laminate and the laminate boundary near the hole wall were the most critical regions for damages during bolt insertions. However, the influence of those damages on quasi-static failure loads and fatigue failure modes of joints was minimal. Delamination and matrix cracking occurred first in laminates following fiber and matrix fracture in quasi-static tensile tests. Interference fit could improve the fatigue resistance of the laminate hole; however, the bolt seemed to suffer a more critical local fatigue loading condition. This paper can contribute to composite structure designs, especially in understanding damage and failure behaviors of composite bolted joints.     

复合材料径向和轴向螺栓连接失效预测方法及失效模式分析

大型火箭舱段间的复合材料端框连接主要由径向螺栓连接和轴向螺栓连接组成，设计了不同铺层和几何尺寸的连接试验件，并通过试验获得了失效载荷和失效形式。然后，选择了3种渐进损伤方法进行了连接结构的失效预测，并将预测结果与试验结果进行比较，结果表明：采用基于细观力学的复合材料渐进损伤方法，15组径向连接试验件失效载荷计算误差最大为17.3％；4组轴向连接失效载荷计算误差最大7.4％；预测的失效形式与试验结果接近，为连接结构确定了合适的失效预测方法。采用数值分析结果揭示了复合材料单向层的主要失效模式。为复合材料端框连接的设计研究提供了可用的失效预测方法及详细的失效模式分析结果。     

Nonlinear dynamic analysis of a multi-link manipulator with flexible links-joints mounted on a mobile platform

The present work theoretically demonstrates the dynamic analysis of a planar multi-link manipulator considering flexible links and joints mounted on a moving base. A nonlinear model of a multi-manipulator (N-links) has been developed accounting for an equivalent bi-directional mobile base. The nonlinear Euler-Bernoulli beam and spring-inertia/mass system have been introduced to demonstrate the flexibilities of links and joints, respectively. Modal analysis followed by trajectory analysis has been performed to investigate the behaviors of manipulator taking into account of accurate boundary conditions. Further, vibration characteristics, steady-state responses, and their stability at resonant situations due to joint motions and inertial coupling have been studied. Results of exploiting geometric and inertial coupling due to flexible arms on stability analysis of steady-state responses have been investigated and have been subsequently verified with the findings by directly solving the governing equations. Steady-state response characteristics to explore the dynamics of the multi-link manipulators under resonant states have been studied with the varying actuator mass, the flexibility of links, lifted payload, and joint parameters. The results thus obtained, deliver a useful insight into the position analysis and long-term behavior of multi-link flexible manipulators under harmonic hub-joint motions that shall further enable its proper vibration attenuation and control.     

点焊接头超声C扫描图像分析及焊核直径测量

采用超声波扫描显微镜获取了点焊接头C扫描图像,分析点焊接头C扫描图像灰度值的分布特征,提出了一种对焊核边缘、焊核直径进行快速检测分析的方法;对不同焊接工艺参数下的不锈钢点焊接头进行表面检测,对比分析基于C扫描图像的焊点检测结果与实际测量值。结果表明,通过这种测量方法不但可以快速得到焊核边缘及焊核尺寸,而且避免了人为因素的影响;与实际测量结果相对比,两者之间相差较小,证实了该检测方法的可行性。     

Integration of nanoindentation and finite element method for interpretable tensile properties:A cross-scale calculation method of uneven joints

Nanoindentation testing and its Reverse Analysis Method(RAM) show great potential in understanding the tensile properties of metallic alloys with various microstructures. Nevertheless,the tensile properties of heterogeneous materials such as nickel-based superalloy welded joints have not been well interpreted by combining the microstructures and nanoindentation results, due to their diverse and complex microscopic zones, which throws shade on the properties of separated zones in the material. He...