航空带垫卡箍刚度及阻尼特性分析与试验验证

研制了带垫卡箍刚度测试装置,分别对不同规格卡箍线刚度和扭转刚度进行了测量,并将卡箍刚度测量数值引入卡箍-管路系统有限元模型,通过管路固有特性数值计算与试验测试结果对比,误差在5％左右,验证了卡箍刚度参数的准确性.进一步搭建了卡箍阻尼测量系统,通过测量卡箍动态传递率,获得相对应的模态阻尼比,并将卡箍阻尼测量数值引入卡箍-...     

化学气相反应法在C/C复合材料抗氧化处理中的应用

通过把硅蒸气渗入预制体孔隙与碳直接反应生成SiC的化学气相反应(CVR)方法,提高初始密度和预制体结构均不同的C／C复合材料的抗氧化能力,研究了C／C复合材料的密度变化与微观结构,并对其进行了氧化试验。结果表明,因CVR温度、C／C复合材料初始密度不同,抗氧化处理后的密度增加量有显著不同。针刺炭布C／C／SiC复合材料在马福炉中于1160℃经65min氧化后,其失重率仅2．6％,而密度为1．95g／cm^3的同结构C／C复合材料相在同条件下失重率高达32％。     

小卫星非常规动力学分析与控制

针对小卫星研制中出现的一些非常规动力学问题进行研究,并提出解决办法。针对小卫星组件最大冲击谱量级超出常规冲击试验规范谱的分析与验证困难,通过研究提出了能够分析评估组件高量级冲击的方法。针对小卫星随机振动下强度设计方法还存在较大误差,分析了系统模态质量比与模态频率在一定频段的影响规律,认为忽略模态质量耦合会带来误差,提出了考虑模态质量耦合的准静态载荷计算方法。最后,针对小卫星整星开展了减振研究,分析了正弦和随机减振效果,对于对称安装减振系统,提出了减振系统的主频率计算公式。     

复杂动力学模型下星载天线跟瞄控制技术研究

针对星载天线动力学复杂这一问题,从天线系统刚柔耦合动力学建模、指向跟踪控制以及振动抑制等方面研究了柔性星载运动部件的指向控制方法。首先,通过描述系统几何拓扑关系建立系统运动学方程,从而简化动力学建模过程;之后,利用假设模态法,对天线反射面挠性进行建模;最后,将拉格朗日方程与挠性关节模型相结合,从而建立了星载天线非线性刚柔耦合动力学模型。在以上复杂动力学建模的基础上,采用分层设计的思路进行了控制策略设计：先运用基于计算力矩法的滑模控制器得到不考虑挠性关节的耦合控制律,从而保证卫星基体的稳定性以及天线挠性反射面的振动抑制;再使用反步法对挠性关节进行控制,实现对天线反射面的指向精度控制。最后,讨论了动力学参数不确定性对系统跟踪指向控制的影响并采用数学仿真的方式验证了相关动力学模型与控制算法。仿真结果表明该方法能较好地实现对星载天线的指向跟踪控制以及振动抑制,提高星载天线的动态指向精度。     

基于压电纤维复合材料的航天器动力学建模与振动抑制

压电纤维复合材料(MFC)在柔性航天器的振动主动抑制中具有很好的应用前景。利用哈密顿原理和压电驱动的载荷比拟方法,建立了带MFC压电驱动的离散形式的刚柔耦合动力学方程,采用线性二次型最优控制(LQR)算法进行主动控制。结果表明：在航天器的柔性体受到脉冲载荷激励条件下,使用MFC驱动器可以实现航天器挠性振动的快速抑制,并且同时保持中心刚体姿态的稳定性,即能够实现挠性振动与姿态运动的协同控制。基于MFC的主动控制方法对于高频响应也具有较好的控制效果。对于柔性占优的航天器,采用MFC的主动控制优于被动控制。本文方法在处理具有复杂柔性体的航天器时更具优势,更适合于工程应用。     

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

Investigation on nonlinear lateral-torsional coupled vibration of a rotor system with substantial unbalance

Substantial unbalance may be caused by fan blade off during the operation period of gas turbine engines, and related dynamic problems are very critical to the safety design of rotor system in aero-engine. This article aims to understand lateral-torsional coupled vibration of the rotor system with substantial unbalance. The governing equation of a modified unbalanced rotor system is established based on Lagrangian approach. Then, a mathematical analytical method is proposed in which a linear approximation is derived and the Floquet theory and Hill’s method are incorporated, from which the modal characteristics of the unbalanced rotor are obtained. The modal characteristics of the unbalanced rotor system are revealed comprehensively for the first time. Furthermore, the relation between the modes and responses of the unbalanced rotor is discussed in detail. The results show that the lateral vibration and torsional vibration of the unbalanced rotor are coupled through the inertial terms in the governing equations. Due to the coupling, veering and lock-in phenomena occur between the frequencies of the forward whirl mode and the torsional mode. Furthermore, lock-in can lead to a kind of principal instability. With regard to the response of the unbalanced rotor, both natural vibration components and enforced vibration components appear in the lateral response, while only natural vibration components appear during torsional vibration. Moreover, natural vibration components play a crucial role in the response within the principal instability region and cause divergence of the vibration amplitudes in the lateral and torsional directions.     

椭圆振动切削加工的同步控制研究

利用椭圆振动切削加工的回转体表面微织构是在机床主轴旋转、平台进给和装置椭圆振动的联合运动下得到的,机床主轴转动与装置位移输出如果不能保持完全的实时同步,会造成微织构加工的偏差。为了解决这一问题,提出了一种新的基于转角的同步控制方法,该方法在主轴的对位基准处实现装置正弦信号的复位,以修正转速漂移造成的加工位置误差,并通过判断主轴角度信号实时输出对应幅值电压来实时同步信号输出和机床旋转运动。基于LabVIEW FPGA搭建同步控制模块,经试验验证,利用该方法加工的矩形阵列微织构轴向排列与中轴线平行,与周向排列的夹角和仿真结果的偏差不超过0.1°,织构深度随转角的不同发生预设的变化,因此,同步控制方法具有实时同步控制椭圆振动切削装置的能力。     

Analysis on Output Power for Multi-direction Piezoelectric Vibration Energy Harvester

To predict the performance of multi-direction piezoelectric vibration energy harvester,an equation for calculating its output power is obtained based on elastic mechanics theory and piezoelectricity theory.Experiments are performed to verify theoretical analysis.When the excitation direction is along Y direction,a maximal output power about 0.139 mW can be harvested at a resistive load of 65kΩ and an excitation frequency of 136 Hz.Theoretical analysis agrees well with experimental results.Furthermore,the performance of multi-direction vibration energy harvester is experimentally tested.The results show that the multi-direction vibration energy harvester can harvest perfect energy as the excitation direction changes in XY plane,YZ plane,XZ plane and body diagonal plane of the harvester.     

Influence of pre-tension on ballistic impact performance of multi-layer Kevlar 49 woven fabrics for gas turbine engine containment systems

In this paper, ballistic impact tests on wrapped multi-layer Kevlar 49 woven fabric systems were carried out with a flat blade projectile to investigate the impact response during a fan blade out event. The influences of the number of Kevlar layers and pre-tension were discussed particularly. Test results were used to analyze failure modes and energy absorption characteristics of multi-ply Kevlar fabrics. Results show that there are two kinds of impact damage for fabrics: global deformation mainly involving stretching of yarns in the impact region and fabric wrinkle from both sides to the impact zone, and local damage characterized by yarn fracture, yarn pull-out, and yarn unraveling. The energy absorption capability of Kevlar 49 woven fabrics improves with the number of fabric layers. The energy absorbed by multi-layer fabrics increases slightly at the beginning and then decreases substantially with pre-tension. The work in this paper can provide guidance for designing light-weight multi-layer fabrics containment systems.