锯齿冠低压涡轮工作叶片叶冠防错位设计方法

针对锯齿冠低压涡轮工作叶片在使用过程中发生的叶冠错位故障,在综合分析各次叶冠错位故障发生原因的基础上,总结了锯齿冠低压涡轮工作叶片叶冠错位模式,绘制了模式图,并针对各种叶冠错位模式提出了1套完整的锯齿冠低压涡轮工作叶片预防叶冠错位的设计方法。在2型发动机上进行应用的结果表明,本方法是切实可行的。     

航空齿轮磨削加工安装偏心误差补偿研究

磨齿加工时齿坯几何中心与回转工作台轴心存在安装偏心误差,降低了磨齿加工精度。以数控成型砂轮磨齿机工作原理为基础,建立偏心误差磨削加工几何模型;提出安装偏心误差补偿法,建立偏心误差补偿数学模型,通过数学模型求出磨削砂轮在X、Y两个方向的进给补偿增量;以YK73125数控成型砂轮磨齿机为例,进行安装偏心误差补偿实验,齿轮的左右齿面单个齿距极限偏差绝对值分别减小了0.9μm和1.6μm,齿距累积总偏差绝对值分别减小了49.6μm和43.3μm。结果表明:安装偏心误差与单个齿距偏差和齿距累积总偏差成正比;采用安装偏心误差补偿进行磨齿加工,有效地减小了单个齿距偏差和齿距累积总偏差,齿轮的精度有所提高。     

波音737NG飞机水平安定面疲劳裂纹处理方法分析

根据波音737NG飞机的维护数据,该文分析波音737NG飞机水平安定面主要结构的受力特性;同时,定性分析了水平安定面肋下缘条及连接的蒙皮等部位的典型疲劳裂纹。分析波音公司针对该问题对现有机队的预防性改进措施,借鉴大修厂的实际维护经验以及一系列数据和现场照片,最终给出针对该疲劳裂纹的建议措施,以供民机设计制造单位及波音737NG营运人参考借鉴。     

基于确定接触迹线的点接触齿轮副构建及实验

提出一种点接触齿轮副,在已知齿面上根据设计需要确定接触迹线,推导其共轭曲线,将齿廓曲线沿共轭曲线扫掠后形成轮齿齿面,构建与已知齿轮正确啮合的配对齿轮,并推导该齿轮副的滑动系数计算方法;以渐开线内齿轮为已知齿轮,设计以抛物线齿面作为轮齿齿面的配对齿轮,进行齿轮样机制造和效率实验研究。结果表明,该齿轮副在啮合过程中时刻保持点接触状态,啮合点沿着理论接触迹线移动,与理论分析一致;滑动系数的大小取决于齿轮两端选取啮入点和啮出点所对应的渐开线参数值范围;实验后齿轮副实际接触迹线与理论接触迹线一致,且效率稳定在97.2%~98.5%。      

承载传动误差最小的高重合度弧齿锥齿轮波动齿面设计

为改善航空弧齿锥齿轮的承载啮合性能,结合ease-off技术提出一种波动齿面设计方法以降低高重合度弧齿锥齿轮的承载传动误差。鉴于中凹型修形曲线（修形齿面的几何传动误差曲线）可极大地减小高重合度弧齿锥齿轮传动的承载传动误差波动幅值,创建一种与高重合度相适应的波动齿面修形模型;结合ease-off技术建立以降低承载传动误差波动幅值为目标的优化模型;通过优化得到具有良好啮合性能的高重合度弧齿锥齿轮。分析发现:优化后2阶传动误差设计弧齿锥齿轮传动的承载传动误差波动幅值降低了34.152%,而由波动齿面设计方法所得改进修形弧齿锥齿轮的承载传动误差进一步降低了61.492%,有效地改善了高重合度弧齿锥齿轮传动性能,为高性能弧齿锥齿轮齿面设计奠定理论基础。      

Modeling and experiment of grinding wheel axial profiles based on gear hobs

Hobbing is one of the crucial gear manufacturing processes with high precision and high efficiency. In order to improve the accuracy of hobbing and hob relief grinding, more precise grinding wheels are demanded for relief grinding in the production of gear hobs. In this paper, a new and accurate mathematical method for calculating the axial profile of grinding wheel based on the corresponding gear hob to be ground is proposed. Considering that most researches have been conducted to focus on the optimization of hob geometric feature and only can be applied to a specific type of hand of helix and rake angle of gear hobs. The method in this paper can be served as a general algorithm for generating axial profile of grinding wheels on the basis of the spatial envelope theory, the principle of coordinate system transformation, and studies on normal profile of single-tooth. The accuracy of grinding hobs is based on applying the approach in practical manufacturing. Taking two typical different kinds of pre-grinding gear hobs as examples for calculation and experiment, the results of tooth profile errors strengthen the position that the validity and feasibility of this method, it can be employed for gear hob design and grinding processing.     

滤波减速器有限长轮齿接触表面混合润滑分析

综合考虑了轮齿接触几何、啮合点法向载荷、齿向参数、真实表面粗糙度、润滑剂流变特性等因素,建立了滤波减速器轮齿混合润滑数值分析模型,采用复合迭代法和快速傅里叶变换(FFT)方法分别求解Reynolds方程和弹性变形方程,获得了轮齿接触表面混合润滑分析完全数值解,得到了滤波减速器在啮入点、节点和啮出点的压力与平均油膜厚度,以及转速对轮齿接触表面平均油膜厚度和接触比的影响.结果表明:在啮入点、啮出点及节点处,沿齿宽方向的压力分布不相等,两侧压力较大,而在啮入点处的两侧压力突变相对较小,且平均油膜厚度最大;对于粗糙轮齿接触表面,随着滤波减速器转速逐渐降低,啮入点、节点及啮出点的平均油膜厚度随之减小,接触比增加,润滑效果变差,并且在同一工况下粗糙轮齿接触表面的啮合点平均油膜厚度小于光滑轮齿表面的平均油膜厚度.      

基于热态叶型的小轮毂比弯掠叶片结构保形设计与优化

发展了一种保持且基于气动设计给定的热态叶型的冷态叶型迭代解算方法,并将其融入叶片罩量调节的优化设计,其中在热态叶型的基础上调节罩量,针对冷态叶型计算变形与应力等,变形后的叶片逼近热态叶型,尽可能减小了对热态叶型气动特性的影响.实现了冷态叶型迭代求解与罩量调节中结构有限元网格的自动更新,并基于iSIGHT优化平台,建立了叶片罩量调节多目标优化设计的自动化分析流程,并以一小轮毂比弯掠风扇叶片罩量调节为例,考查了罩量调节中考虑轮盘与否对优化设计结果的影响.计算分析实例表明:所发展的方法可在保持热态叶型的前提下使叶片最大应力和最大变形分别下降了10.6%和46%.      

基于Kalman滤波的空天飞行器再入制导算法

针对空天飞行器应用传统数值预测校正再入制导算法实时性不佳的问题,提出一种基于Kalman滤波的预测校正制导算法。该算法采取四阶多项式拟合速度-高度飞行剖面,利用Kalman滤波估计选定的速度点对应的高度,得到满足再入走廊及航程要求的拟合系数。在此基础上,减少一个终端约束,增加一个待估计剖面参数,可实现对再入过程飞行时间的调节。研究发现,再入过程中通过在线辨识修正不确定性参数能够提高制导指令的适应性;飞行末段利用跟踪参考剖面制导可有效避免飞行速度与终端速度接近时发生拟合系数求解发散的问题。多组不同再入条件下的算例仿真结果表明,基于Kalman滤波的空天飞行器再入制导算法实时性好,制导精度高,能够实现飞行时间可控,具有较强的鲁棒性和工程应用潜力。     

Grinding force and surface quality in creep feed profile grinding of turbine blade root of nickel-based superalloy with microcrystalline alumina abrasive wheels

Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles.