某飞行器用紧固件拧紧力矩与预紧力关系研究

分析了某飞行器部段连接紧固件拧紧力矩与预紧力的关系,以M8、M10规格钛合金紧固件为研究对象,着重研究了钛合金紧固件在飞行器部段实际安装环境下,安装次数对拧紧力矩与预紧力的影响,以及扭拉系数随安装次数的变化规律.研究结果表明:当螺栓的预紧力达到10％Fmax～50％Fmax(Fmax为螺栓的理论破坏拉力值)时,钛合金紧固件螺纹副的拧紧力矩与预紧力呈良好的线性关系;随着反复拧入次数的增加,达到相同的预紧力时,所需的拧紧力矩呈现递增的变化规律,其扭拉系数也明显呈递增变化趋势.     

利用小尺寸缺口试样测定延性材料的单轴本构关系

提出了一种利用三点弯曲试样获取延性材料本构关系的测试方法：针对小尺寸缺口试样的三点弯曲线载荷-位移曲线,采用有限元辅助测试（Finite-element-analysis aided tests,FAT）方法,迭代获得材料代表性体积单元（Representative volume element,RVE）本构关系。研究表明,两种延性材料的有限元迭代反求结果和单轴拉伸试验结果吻合较好。应用该方法,可以采用小尺寸缺口试样来获取延性材料的本构关系。     

A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

改性双马来酰亚胺树脂预浸料性能研究

采用二烯丙基双酚A(Ortho-dially Bisphenol A,以下简称O-DABPA)对T型双马来酰亚胺(Bismaleimide,以下简称BMI)树脂进行改性,并用红外光谱(Fourier TransformInfrared,以下简称FT-IR)、差式扫描量热仪(Differential ScanningCalorimetry,以下简称DSC)对改性前后的树脂结构及固化反应进行测定,利用热熔预浸法对改性BMI树脂制备预浸料,考查了预浸料的力学性能及高温下的弯曲性能。结果表明,在175℃下二烯丙基双酚A和T型双马来酰亚胺树脂质量比为1∶1,反应时间为1 h时,改性BMI树脂制备的预浸料工艺性良好,单向板层间剪切强度为84.86 Mpa,在240℃时,弯曲强度及模量分别为1 326.41 MPa和120.31 GPa,强度保留率为76.73%。     

一种修正的双模式盲均衡算法研究

传统的CMA盲均衡算法存在收敛速度较慢、稳态均方误差较大的缺点。结合了判决引导算法的CMA算法虽具有稳态均方误差小的优势，但是算法本身收敛能力弱，在信号眼图未张开的条件下难以保证算法收敛。针对上述不足，提出了一种含软判决思想的双模式盲均衡算法。该算法通过最大化均衡器输出信号的后验概率密度函数来获得均衡器抽头系数的最优值。计算机仿真结果表明，所提算法可以有效地纠正输出信号的相位旋转，具有较好的均衡效果。     

基于双框架控制力矩陀螺的航天器动量管理

为减小维持大型航天器的姿态稳定和降低能量消耗的动量管理中的扰动力矩对姿态稳定的干扰,设计了周期性抑制滤波器。姿态控制的执行机构采用双框架控制力矩陀螺群（DGCMGs）,应用KENNEL操纵率,使航天器执行机构的角动量在本体系的x轴分量和偏航角可达稳定,同时角动量在本体系的z轴分量和滚转角可在较小的范围内振荡。数值仿真结果验证了方案的可行性。     

探针测定流场的水动力学问题

研究探针测定水流场针孔压力测量反应时间的影响因素，给出探针测试系统合理参数，分析探针杆水力共振和受水绕流阻力挠曲的影响，提出相应对策，以提高测试精度。     

Singularity analysis for single gimbal control moment gyroscope system using space expansion method

Control Moment Gyroscope (CMG) is an effective candidate for agile satellites and large spacecraft attitude control because of its powerful torque amplification capability. The most serious situation, however, in using CMG is the inherent geometric singularity problem, where there’s no torque output along a particular direction. Space expansion method has been proposed in this work for the singularity analysis. Based on inverse mapping transformation, an expanded Jacobian matrix which is a full rank square matrix is obtained. The singular angle sets of the 3-parallel cluster and pyramid cluster are distinguished using space expansion method. An effective hybrid steering strategy, able to deal with the elliptic singularity, is further proposed. Simulation results demonstrate the excellent performance of the proposed steering logic compared to the generalized singular robust logic and pseudo inverse logic in terms of energy consumption and torque error.     

闭合薄壁剖面杆刚度计算的有限元素法

利用有限元法对飞机闭合薄壁剖面杆结构进行刚度计算，其结果与全尺寸试验值吻合较好。