Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

火星大气来流模拟装置CFD仿真与试验

根据我国火星着陆巡视器工作过程,其着陆发动机需要在相对火星大气高速迎风运动中可靠点火。由于巡视器着陆时发动机喷管出口气流与火星稀薄气流方向相反,目前无法通过理论计算准确获得着陆过程的动态流场对发动机起动过程的影响量值。为验证火星着陆环境下发动机点火的适应性,需要建立发动机的火星大气来流试验环境模拟条件。为模拟发动机在火星大气条件下的相对运动,在真空舱内发动机保持固定,前端设置环形来流形成装置,该装置在发动机喷管周围形成一定速度的逆向来流包络。采用数值模拟技术结合试验验证方法,在火星着陆器巡视器主发动机性能考核试验中,针对来流的形成装置开展了设计研究工作。来流模拟试验测试数据表明:在确保贮箱供应压力稳定的条件下,来流模拟系统能够形成100~200 m/s速度的稳定来流,发动机在来流下能稳定启动工作,真空舱压力满足试验要求。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

基于Ansys Fluent的近场翼尖涡数值模拟与分析

为了进一步研究飞机远场尾涡,提供网格分配及湍流模型的参考,并为整机模拟提供必要的参考依据,通过基于Ansys Fluent的数值模拟方法,研究了NACA0012机翼的近场翼尖涡流场,采用有限体积法求解不可压缩雷诺平均Navier-Stokes方程,其中雷诺应力项分别以S-A和Realizable k-ε模型封闭,模拟了近场翼尖涡卷起的过程,分析了机翼表面压力以及涡核参数,包括轴向涡量、涡核位置、涡核粘性等,并与风洞实验结果进行了对比。结果分析表明:基于局部O-网的六面体网格,RKE模型要优于S-A模型,与实验值更为吻合。     

提高某铝合金薄壁深孔零件加工质量研究

通过分析某铝合金薄壁深孔零件在加工过程中存在的问题基础上,采用了拉镗拉铰加工内孔,再以轴向定位夹紧的方式加工外形的思路,该方法保证了零件加工精度,解决了该铝合金薄壁深孔零件的加工问题,完全满足生产实际需要,质量稳定可靠,可为类似零件加工提供参考。     

加筋壁板VARI整体成型工艺设计与验证术

针对一种典型复合材料加筋壁板,完成模具结构及工艺流程等整体成型工艺设计,同时利用PAM-RTM软件完成流道设计优化模拟,并根据模拟结果选择合理的注射方式及流道布局,最终根据所选方案完成工艺试验验证,对构件进行超声无损检测,检测结果显示构件没有内部缺陷、树脂充分填充,最终验证了加筋壁板整体成型工艺设计及模拟分析的有效性.     

高能电子辐照下介质-导体相间结构深层充电特性研究

为研究影响介质-导体相间结构深层充电特性的内在因素,设计了不同构型的试验样品,利用90Sr放射源模拟空间高能电子环境对样品进行深层充电辐照试验,测量了充电电位的差异。并借助深层充电三维仿真软件计算介质-导体相间结构在不同几何构型情况下的深层充电电位、电场分布。试验和仿真结果表明,介质最高表面电位以及介质内部最大电场均与介质宽度和高度呈正相关。其他条件不变时,介质越宽,或越高于导体表面,发生放电的风险就越高。在介质与导体侧面存在微小缝隙情况下,介质内最大电场显著增强,易发生内部击穿。而在介质与导体之间的真空间隙内,电场很容易超过击穿阈值,放电风险很大。航天工程应用中为降低此种结构深层充放电的风险,在满足绝缘性能及其他要求的前提下应尽量减小介质的宽度,降低介质与导体间的高度差,并确保介质与导体侧面接触良好。     

某型教练机嵌入式训练系统顶层设计技术研究

本文通过对该型教练机现有航空电子系统构型、驾驶员操作程序、接口控制文件深入研究,结合未来功能扩展需求,给出了合理的系统构型分析、功能分配、数据流规划、原相关系统软件改动分析,在此基础上还设计出了嵌入式训练系统技术方案.依据方案研制的嵌入式训练系统原理样机通过系统动态试验、航电系统地面综合试验和飞机地面通电试验,证明系统...     

一种基于余数周期的 PRI精确估计算法

针对传统脉冲重复间隔（PRI）分选算法在估计PRI方面存在的不足，提出了一种对PRI周期信号的周期进行精确估计的算法。该算法首先从待分选脉冲序列中提取出属于一部雷达的脉冲样本，然后利用同余方程的余数周期性质对该雷达脉冲序列的PRI进行精确的估计。相对于传统的PRI估计算法，该算法有效地消除了TOA量化误差对PRI估计造成的影响，可以精确地估计出雷达脉冲序列的准确 PRI数值，从而能够更好地满足信号分选算法的处理需求。理论推导及仿真实验均表明了该算法的有效性。     

先进航发旋转雾化喷嘴制造技术

喷射油道是一种高精度旋转雾化喷嘴,其非连续窄深端槽、窄深槽、3/4圆弧窄端槽为行业内少见结构.通过分析喷射油道特有结构的加工工艺,摸索油孔尺寸与燃油流量的匹配关系,解决了非连续深窄端槽、窄深槽、细微孔电火花成形加工、3/4圆弧窄端槽高效数控加工、高精度喷嘴孔流量调试等关键技术瓶颈,具有一定的指导意义和广阔的应用前景.