TiAl合金不同钛铝比层片组织的稳定性

对钛铝比为１．１７４、１．１０５和１．０４１的（ＴｉＡｌ）－２．５Ｖ－１Ｃｒ（ａｔ％）合金层片组织在１３２３Ｋ热暴露中的组织变化进行了观察和分析。发现钛铝比对ＴｉＡｌ合金层片组织的稳定性和失稳分解机理有重要影响，钦铝比适当大于１：１（如１．１０５）的合金可以得到稳定性更好的层片组织。     

组合催化剂MT在丁羟推进剂中的应用

研究试验了组合催化剂MT在丁羟推进剂中提高燃速和降低燃透压强指数的作用。结果表明，MT与不同含量和粒度小于10μm的AP匹配使用，燃速可在9mm／s～30mm／s范围内调节；压强指数均小于0．2（压强范围3MPa～9MPa），出现“平台”燃烧效应；发动机实测的压强指数与试验结果基本一致；选用合理的M与T组合比，可不影响推进剂制造工艺性能和药柱力学性能。对结果的理论分析认为，M与T对改善AP低压下热分解具有协同效应。     

基于FW-H方程的旋翼气动声学计算研究

由流体力学N S方程导出的非齐次波动方程———FfowcsWilliams Hawkings方程(简称FW H方程),可以精确地描述在静止流体中运动的物体与流体相互作用的发声问题。以FW H方程为理论模型,将旋翼桨叶运动发声问题等效为包含桨叶的任意运动控制面(声源面)的声辐射问题,并在旋翼绕流Euler方程数值模拟的基础上,在时域内计算了悬停旋翼和前飞旋翼的声场。应用于UH 1H和AH 1/OLS两种旋翼模型的气动声学计算表明:计算结果与噪声实验值符合良好;所研制的程序不仅能够较准确地计算单极子噪声和偶极子噪声,而且具有较强的跨音速四极子噪声预测能力。     

Deep Impact: Working Properties for the Target Nucleus – Comet 9P/Tempel 1

In 1998, Comet 9P/Tempel 1 was chosen as the target of the Deep Impact mission (A’Hearn, M. F., Belton, M. J. S., and Delamere, A., Space Sci. Rev., 2005) even though very little was known about its physical properties. Efforts were immediately begun to improve this situation by the Deep Impact Science Team leading to the founding of a worldwide observing campaign (Meech et al., Space Sci. Rev., 2005a). This campaign has already produced a great deal of information on the global properties of the comet’s nucleus (summarized in Table I) that is vital to the planning and the assessment of the chances of success at the impact and encounter. Since the mission was begun the successful encounters of the Deep Space 1 spacecraft at Comet 19P/Borrelly and the Stardust spacecraft at Comet 81P/Wild 2 have occurred yielding new information on the state of the nuclei of these two comets. This information, together with earlier results on the nucleus of comet 1P/Halley from the European Space Agency’s Giotto, the Soviet Vega mission, and various ground-based observational and theoretical studies, is used as a basis for conjectures on the morphological, geological, mechanical, and compositional properties of the surface and subsurface that Deep Impact may find at 9P/Tempel 1. We adopt the following working values (circa December 2004) for the nucleus parameters of prime importance to Deep Impact as follows: mean effective radius = 3.25± 0.2 km, shape – irregular triaxial ellipsoid with a/b = 3.2± 0.4 and overall dimensions of ∼14.4 × 4.4 × 4.4 km, principal axis rotation with period = 41.85± 0.1 hr, pole directions (RA, Dec, J2000) = 46± 10, 73± 10 deg (Pole 1) or 287± 14, 16.5± 10 deg (Pole 2) (the two poles are photometrically, but not geometrically, equivalent), Kron-Cousins (V-R) color = 0.56± 0.02, V-band geometric albedo = 0.04± 0.01, R-band geometric albedo = 0.05± 0.01, R-band H(1,1,0) = 14.441± 0.067, and mass ∼7×10¹³ kg assuming a bulk density of 500 kg m⁻³. As these are working values, {i.e.}, based on preliminary analyses, it is expected that adjustments to their values may be made before encounter as improved estimates become available through further analysis of the large database being made available by the Deep Impact observing campaign. Given the parameters listed above the impact will occur in an environment where the local gravity is estimated at 0.027–0.04 cm s⁻² and the escape velocity between 1.4 and 2 m s⁻¹. For both of the rotation poles found here, the Deep Impact spacecraft on approach to encounter will find the rotation axis close to the plane of the sky (aspect angles 82.2 and 69.7 deg. for pole 1 and 2, respectively). However, until the rotation period estimate is substantially improved, it will remain uncertain whether the impactor will collide with the broadside or the ends of the nucleus.     

固体火箭发动机性能蜕变的压强补偿

介绍了采用缩小喷管喉径的方法，对固体火箭发动机燃烧室压强和推力进行补偿，以达到延长发动机使用寿命的目的。     

高超声速三维碳—碳烧浊流场的数值研究

本文针对高超声速再体的烧蚀现象 ,利用简单隐式TVD差分格式和激波捕捉法 ,数值求解三维化学非平衡Navier Stokes方程 ,其中化学模型是碳 碳 (C C)空气化学模型 ,考虑 12个化学组分和 31个化学反应过程 ,研究了C C烧蚀对再入体头部区域的壁面温度和热流分布的影响。为了计算效率和稳定性提出壁面条件显式处理的方法。对再入高度为 6 5km和速度为 8km/s的再入体头部区域烧蚀流场进行了数值模拟 ,用飞行迎角α =0°的计算结果与国外文献进行了比较 ,符合得较好。同时给出了三维小迎角α =5°的计算结果     

芳纶纤维／环氧复合材料界面超声连续改性处理

运用超声技术在芳纶/环氧复合材料制备过程中对其界面进行改性处理,分析了超声处理过程中纤维与树脂之间浸润性的变化趋势以及超声作用对复合材料界面性能和力学性能的影响。结果表明:超声是通过改善纤维与树脂之间的浸润性,提高复合材料的界面性能及力学性能。     

基于BP人工神经网络的GPS／SINS组合导航算法

基于扩展Kalman滤波的GPS／SINS组合导航算法，需要对原始的非线性连续系统模型进行线性化和离散化处理，要求系统噪声和测量噪声为零均值的高斯白噪声，且易于出现滤波器发散。BP人工神经网络毋需对所求解的问题建模，能够很好地逼近系统非线性特性，获得较高精度的导航定位信息；还具有计算过程稳定，不涉及矩阵求逆，不需要迭代逼近，以及容易实现并行处理等优点。本文设计适用于GPS／SINS组合导航系统的BP网络模型，并在标准的BP算法基础上，采用共轭梯度法改进网络训练速度及精度。最后，通过仿真算例说明BP网络方法用于GPS／SINS组合导航计算的可行性。     

利用虚拟仪器实现角速度波动率的采集和处理

利用NI 的PXI-6281高速数据采集卡来完成角速度波动信号的采集,借鉴信号失真度的概念,分析角速度反馈信号的基波和高次谐波大小,求取高次谐波与基波幅值比,作为角速度波动率.     

粘流与无粘流的相互作用计算

本文总结了粘流/无粘流的各种计算方法和结果。重点在于介绍定常流动中的弱相互作用。首先叙述了弱相互作用的数学模型。给出了不可压流动和跨音速流动中粘流/无粘流相互作用的某些正耦合的计算结果。讨论了在分离区附近边界层正方法失效的原因。然后介绍了边界层反方法和适用于带分离的流动中半反方法耦合的粘流/无粘流的相互作用方法。文中也简单地总结了三维情况的应用和强相互作用。