Effect of curing condition on bonding quality of scarf-repaired composite laminates

Both single-face vacuum bag curing (SVC) and double-face vacuum bag curing (DVC) can be used in scarf repair of composite structures. But different curing conditions caused by the sealing state may affect the bonding quality of scarf-repaired structures. In this paper, the effect of curing condition on bonding quality of scarf-repaired laminates was experimentally investigated in terms of surface profiles, moisture absorption curves and section profiles. In order to further explore the moisture absorption mechanism, finite element model of the repaired laminates using DVC was established with moisture diffusion of both the adhesive and composite laminates considered. This model was verified by experimental results. Based on the model of DVC case, the model of SVC case was built by changing moisture absorption parameters of the adhesive. Results show that SVC reduces the bonding quality, mainly reflecting in more adhesive inner voids and patch-to-parent dislocation. And SVC increases moisture absorption rate and moisture equilibrium content of the adhesive, and its effect on the former is far greater than that on the latter.     

Theoretical aspects of selecting repeated unit cell model in micromechanical analysis using displacement-based finite element method

Repeated Unit Cell(RUC)is a useful tool in micromechanical analysis of composites using Displacement-based Finite Element(DFE)method,and merely applying Periodic Displacement Boundary Conditions(PDBCs)to RUC is almost a standard practice to conduct such analysis.Two basic questions arising from this practice are whether Periodic Traction Boundary Conditions(PTBCs,also known as traction continuity conditions)are guaranteed and whether the solution is independent of selection of RUCs.This paper presents the theoretical aspects to tackle these questions,which unify the strong form,weak form and DFE method of the micromechanical problem together.Specifically,the solution’s independence of selection of RUCs is dealt with on the strong form side,PTBCs are derived from the weak form as natural boundary conditions,and the validity of merely applying PDBCs in micromechanical Finite Element(FE)analysis is proved by referring to its intrinsic connection to the strong form and weak form.Key points in the theoretical aspects are demonstrated by illustrative examples,and the merits of setting micromechanical FE analysis under the background of a clear theoretical framework are highlighted in the efficient selection of RUCs for Uni Directional(UD)fiber-reinforced composites.     

动力失效对起飞纵向气动特性影响数值研究

研究民用飞机动力失效对飞机起飞阶段纵向气动特性的影响规律及其机理,对保证飞机有效操纵和安全飞行具有重要意义.采用在点对点多块结构化网格系统上求解三维可压缩雷诺平均N-S方程的数值方法,研究发动机动力失效对某民用飞机起飞构型纵向气动特性的影响.通过DLR-F11模型验证研究方法对民用飞机高升力构型气动特性的预测能力;针对安装动力短舱的某翼吊涡扇发动机民用飞机起飞构型,通过对比其发动机在正常工况和失效时飞机气动特性的差异,得出动力失效对飞机纵向气动特性的影响规律及机理.结果表明:动力失效后,不但溢流效应会使飞机阻力系数增大;还会导致发动机进、排气特性较正常工作状态明显不同,恶化短舱附近流场,对飞机的升力、失速特性带来不利影响.     

柴油发动机热管理系统的高度特性

基于空中和高原环境的特点,研究了柴油发动机散热器传热性能的高度特性;进一步建立了发动机热管理系统的流动和传热模型,研究了热管理系统的高度特性;给出了基于最小功耗原则的热管理系统运行参数匹配方法.在固定系统热负荷条件下的计算结果表明:随着海拔高度的增加,在空中环境下,散热器的散热性能先上升后下降,热管理系统中冷却液和润滑油温度先下降后上升,热管理系统所需的最小功耗先减小后增加;在高原环境下,散热器的散热性能随高度增加大幅下降,热管理系统中冷却液和润滑油温度大幅上升,发动机出现过热问题,为了给发动机提供足够的散热能力,热管理系统所需要的最小功耗随着海拔高度的增加而大幅增加.      

平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

非正交弧线齿面齿轮齿面设计及根切研究

非正交弧线齿面齿轮是以端面渐开线弧线齿圆柱齿轮为假想刀具包络展成的面齿轮。根据面齿轮啮合原理推导了非正交弧线齿面齿轮齿面方程,结合Matlab数学模型和根切理论研究了该种面齿轮的根切现象,计算出面齿轮不产生根切的最大内径,并通过Catia仿真滚齿来验证计算的准确性。该研究旨在提出一种新型非正交面齿轮,通过理论推导及仿真模拟来研究该种面齿轮的根切现象,在此基础上探究非正交弧线齿面齿轮的内径影响因素。研究结果表明:在同等参数下,当位置参数增大时,刀具渐开线截面高度和内径逐渐减小,当刀具圆弧半径增大时,内径逐渐减小,刀具渐开线截面高度逐渐增大。     

一类滞后不确定相似组合系统的分散控制

本文给出了一个使滞后的相似组合大系统镇定的分散鲁棒控制器的设计方法。不确定性是时变的,是以不确定参数出现在每个子系统中,而存在于互联项中的不确定性假设可能知道它的边界,当系统具有某种特征时,简化了一般控制器的设计。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

计算风工程中几个关键影响因素的分析与建议

通过近几年进行建筑计算风工程的实践与体会,并参考国内外的一些文献,本文给出了合理选取建筑数值风洞大小、最好采用SSTk-ω或BSL雷诺应力湍流物理模型及在建筑模型中的不同区域应按不同的网格尺度要求划分网格的建议;在CFX5软件平台中,对复杂的建筑体型,可选用非结构化网格和四面体单元,对流项的插值格式宜采用接近二阶的混合格式。还选取一立方体建筑模型,通过数值模拟、现场实测和风洞实验结果的比较对建议进行了验证。最后通过未受扰动数值风洞中入口边界条件的保持,给出了适用于我国建筑工程中A、B、C、D四类地面粗糙度类别的入口湍流边界条件,可参考采用。