Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

从系统仿真谈仿真模型的生成

随着计算机科学和系统科学的发展，系统仿真技术愈来愈为人们所关注。其应用范围遍及政治、经济、军事、交通运输、通讯、科学实验、教学及生产管理等社会各部门及领域。而构造仿真模型又是系统仿真中非常重要且必不可少的关键环节。本文对系统仿真模型的生成问题进行了探讨。     

喷射沉积过程中显微组织的形成机制

通过对沉积还纵剖面的组织分析，发现沉积坯在进缘、上下表面及中心部位的显微组织明显不同。边缘及上下表面区试样的退火试验研究表明，细小的枝晶碎块在高温退火过程中发生凝共和粗化，并导致近球状晶粒组织的形成。试验确定其生长服从：D2-D02=6.37×1020e(-70036.1/T)·τ，晶界迁移激活能Qg=582KJ／mol。并依赖于两种机制：（1）在喷射沉积过程中无强烈变形枝晶的均匀化；（2）变形及断裂枝晶的生长和粗化。     

7075铝合金在超塑处理和拉伸过程中的显微组织变化

 研究了 70 75铝合金在超塑性预处理和拉伸过程。结果表明 ,合金经过固溶处理炉冷→轧制预处理后 ,形成 1～ 2 μm的胞块组织。在超塑拉伸过程中胞块发生回复和再结晶 ,形成细晶组织 ,使合金获得优异的超塑性性能     

等温锻造Ti—47Al—2Cr—1Nb合金显微组织细化机理

Ti 4 7Al 2Cr 1Nb(at % )合金经等温锻造形变热处理后 ,显微组织得到显著细化 ;TEM分析表明 ,TiAl合金在等温变形时 ,形变主要以γ相板条内产生变形孪晶的方式进行 ;大部分变形孪晶垂直于α2 /γ界面 ,热处理时易形成再结晶核心 ,形成等轴γ晶粒     

扫描隧道显微镜对粘胶基碳纤维表面微观结构的研究

用扫描隧道显微镜（STM）对粘胶基碳纤维（RCF）表面的微观结构进行了研究，首次获得了原子级的RCF图像，对其原子间距作了精确地量化，并且尝试着将所得到的图像与高定向降解石墨（HOPG）相比较，以期对RCF的微观结构有更深入的了解，在原子级尺度上，发现了原子排列并不规则的石墨状结构，二维视图量化结果表明：相邻原子间距为0．142nm，最近六圆环中心的距离是0．253nm。     

随机声载荷时域信号仿真模型研究

利用航空发动机环行燃烧室噪声测试数据，采用时间序列自回归分析方法得到了燃烧室噪声及动压仿真模型ARMA（17，16），并用其对噪声时间历程数据进行了最佳预测。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

淬火／回火热处理对TiAl基合金晶粒细化的影响

研究了淬火/回火热处理中淬火温度和回火时间对Ti-48Al-2Cr-0.5Mo合金晶粒细化的影响。研究表明:一定的淬火/回火热处理能将大小约为1000μm的铸态组织细化成为18～30μm的均匀双态组织;TiAl基合金的细化效果严重依赖淬火阶段的加热温度,温度升高,得到的块状组织较细,羽毛状组织体积分数减少,在两相区回火时,高温淬火组织的回火组织较细,而时间的延长,晶粒长大,但不明显。     

01420铝锂合金的搅拌摩擦焊接

对2 mm厚的01420铝锂合金薄板实现了搅拌摩擦焊接(FSW),分析焊接接头的微观组织形态,研究焊接工艺参数对搅拌摩擦焊接接头成型和接头性能的影响,并与氩弧焊接接头性能相比较.结果表明,当工艺参数选取得当时,焊缝成型较好,表面光洁,焊接接头的强度可达到母材强度的77%,接头的弯曲角可达到180°,均高于氩弧焊接接头.