扑旋翼飞行器气动特性分析及机翼拓扑优化设计

建立微型扑旋翼飞行器运动学模型,基于面元法研究低雷诺数下非定常场中扑旋翼飞行器的气动特性,得到机翼气动特性和一个工作周期内的最大气动载荷。建立扑旋翼飞行器机翼有限元模型,基于变密度法和独立连续映射法(Independent continuous mapping,ICM)对机翼进行静力学和动力学拓扑优化设计,通过改变机翼拓扑结构优化机翼模态频率,得到同时满足结构静力学和动力学要求的扑旋翼飞行器机翼拓扑结构。本文为扑旋翼飞行器机翼结构优化设计提供了基本思路和研究基础。     

Ionospheric F2-Layer critical frequency retrieved from COSMIC radio occultation: A statistical comparison with measurements from a meridional ionosonde chain over Southeast Asia

In this paper, we compared the F2-Layer critical frequency (foF2) derived from FORMOSAT-3/COSMIC radio occultation (RO) and ionosondes at Chiang Mai, Chumphon and Kototabang during the years 2008–2015 to evaluate the performance of COSMIC RO over Southeast Asia region. The results show that the time development of foF2 values derived from COSMIC RO generally agrees well with those from ionosonde measurements. However, the differences between the foF2 derived from COSMIC RO and that derived from ionosonde observations display latitudinal dependence. COSMIC RO tends to underestimate foF2 at Chiang Mai and Kototabang, which is near to the north EIA crest and the south one, respectively, while a little overestimate foF2 at Chumphon, which is close to the geomagnetic equator. COSMIC RO agrees best with ionosonde at Chumphon and worst at Chiang Mai. At each ionosonde station, the quality of COSMIC RO data degrades with the increase of solar activity. In addition, at the station Chiang Mai and Kototabang, COSMIC RO performs better in summer than in equinox and winter. Furthermore, the differences in foF2 derived from COSMIC RO and that from ionosonde measurements vary with local time, i.e., the differences in foF2 are generally smaller at night and larger in noontime when equatorial ionization anomaly (EIA) is well developed.     

基于锁相环的光电振荡器频率稳定化研究

通过构建小数分频锁相环,将一个工作于X波段的OEO(OptoElectronic Oscillator,光电振荡器)与OCXO(Oven-Controlled Crystal Oscillator,恒温晶体振荡器)进行锁相,得到了输出信号相位噪声和长期频率稳定度的提升。从PLL(Phase-Locked Loop,锁相环)环路传输特性出发,理论分析了PLL输出信号环路带宽内相位噪声水平和作用范围。为降低OEO整体的相位噪声,采用SIL(Self-Injection-Locking,自注入锁定)使OEO在10Hz~10kHz频偏处的相位噪声得到20dB以上的抑制。在此基础上将此SIL OEO与一个频率为100 MHz的OCXO锁相,获得了频率为9.95GHz、相位噪声为-55dBc/Hz@10Hz和-124dBc/Hz@10kHz的微波信号输出,其频率的重叠阿伦方差在100s平均时间内达到1.14×10~(-11),证明了提出的方案对提升OEO频率稳定性具有一定的实际意义。     

采用霍尔传感器的旋翼频率采集设计

为达到对旋翼飞机的控制,需要对旋翼转速进行采集.霍尔转速传感器以其高可靠性等优点常被用来测量转速.介绍了一种使用霍尔传感器进行旋翼转速采集系统,包括硬件构架,逻辑采集单元和软件设计,并给出了优化策略;通过试验数据分析,采集精度达到了预期.     

基于分频段加权的加速振动试验方法

振动环境工程研究现行采用的加速试验方法中,都只考虑了加速因子与频率无关这种情形,这不仅提高了试验设备的推力要求,也增加了位移指标要求。文章提出了一种分频段加权的加速振动试验方法,即通过对低频段加速因子的权重的优化设计,实现较小的位移指标要求,且疲劳损伤累积等效。给出了基于Dirlik方法和TB方法疲劳损伤等效的加速试验设计方法和工程实现流程。针对该方法开展了应用实例的计算,结果表明:在疲劳损伤等效的前提下,显著降低了振动台的位移,且推力基本维持不变。     

带凸肩叶片的断裂故障分析

某型发动机风扇带凸肩的转子叶片发生断裂故障。断口分析表明其为疲劳裂纹特征,其疲劳源在叶盆侧凸肩工作面下侧靠近叶片前缘位置。根据微观分析结论,建立了风扇叶片三维实体模型,利用有限元方法分析了叶片的振动模态。结果表明：叶片在工作时,由于结构的激振可能发生某些阶次的共振,其应力分布与断口分析结果较一致,初步判断叶片是由于共振而发生了疲劳断裂。     

基于直升机/ 发动机综合模型的变旋翼转速控制研究

为了实现直升机旋翼转速在宽广范围内连续变化且涡轴发动机连续提供输出轴功率,采用1种扭矩序列转移控制方案来实现该传动链。通过2台涡轴发动机和2台多级变速器与旋翼协调工作,发动机依次连接或脱开旋翼,提供旋翼转速大范围内变化,并提供旋翼连续变化的功率。在扭矩转移过程中,针对发动机扭矩强扰动问题设计了鲁棒LMI控制器+ADRC扭矩前馈补偿控制器,最后基于直升机／发动机综合模型进行数值仿真,验证了扭矩转移方案的可行性。仿真结果表明：在转移过程中的扭矩强扰动对发动机动力涡轮转速的影响较小,旋翼转速可以实现较大范围内的快速平滑变化。     

一种基于历史标校数据的移相值预测方法

地面测控设备在执行测控任务前,需要对和差接收通道的相位差进行标校(简称校相),以满足测角分系统的目标自跟踪要求.针对因标校设备故障而无法进行校相的问题,通过使用数理统计的多元回归分析方法,对积累的历史标校数据进行分析,确定了设备工作的环境温度对跟踪接收机移相值有显著影响.在此基础上,利用滑动窗口多项式拟合方法得到拟合移相值,并与最近一次的标校移相值进行时变加权,可以得到基于历史标校数据的移相值预测方法.仿真试验表明该方法具有较好的预测精度,可将预测移相值作为跟踪接收机参数,提高测控设备应急测控能力.     

RFID技术在航空领域的应用研究

射频识别(RFID)技术现已广泛用于物流、金融、零售等各个行业.航空领域的RFID应用起步较晚,通过对RFID技术在飞机制造商、原始设备生产厂家(OEM)、航空公司的一些典型的应用案例的分析,提出RFID技术应用于航空领域所面临的挑战及必要性,为其未来航空业自动识别技术的发展指明了方向.     

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.