下缘板孔对涡轮叶片尾缘内冷通道流动换热影响的数值研究

涡轮叶片下缘板出气孔对内冷通道的流动和换热性能有较大影响。通过数值模拟方法研究下缘板出 气孔对尾缘和下缘板双路出气涡轮叶片尾缘内冷通道内的流动和换热特性,对比分析孔径、孔形和孔位置对尾 缘溢流孔流量系数、尾缘出流比、尾缘通道内总压系数和尾缘内冷腔壁面换热特性的影响。结果表明:下缘板 出气孔孔径对流量系数分布的影响显著,孔径增大,尾缘溢流孔流量系数下降,尾缘出流比减小,尾缘内冷通道 内压力损失降低,内冷腔平均换热系数增大;孔形对上游内冷通道内流动和换热几乎没有影响;孔位置变化对 内冷通道壁面整体的换热系数影响很小,对局部影响较大。     

高性能DSP在1553B总线中的设计与实现

为了提高数据采集效率,以高性能DSP芯片为基础,设计了以高性能DSP芯片为处理核心的1553B总线系统.在硬件系统中采用了TI公司的高性能定点运算信号处理器TMS320F2812以及DDC公司的61864协议处理器,同时采用了FPGA作为逻辑控制电路.电路设计方案用于1553总线接口适配的研制,现已通过验收并经测试证明运行稳定可靠.     

机载三股流板翅式冷凝器数值计算与实验研究

分析了翅片、隔板和流体的传热规律,采用有限容积法建立了包含相变流和交叉式在内的多股流板翅式换热器数学模型。基于蒸发制冷循环试验台,在4种工况条件下对机载交叉式三股流板翅式冷凝器换热性能进行了实验,并在特定工况下,通过温度场分析了各股流体间的换热特性。经数值计算与实验结果的对比,流体换热量的最大相对误差为8.08%,满足工程设计计算需求。通过定性分析,认为流体流量分配不均、相变流体潜热以及相变对流表面换热系数的计算是误差的主要来源。     

锯齿扁管内沸腾换热试验

建立以等热流密度方式进行试验件加热的沸腾换热试验系统,分别对当量直径为1.28mm和1.59mm锯齿扁管内R134a工质的沸腾换热特性进行研究,试验参数范围:制冷剂质量流率为68.5~305.5kg/(m2·s),工作饱和压力为0.27~0.46 MPa,加热热流密度为9~42kW/m2。试验结果表明:相同结构的通道,当量直径小换热能力更强;热流密度和饱和压力对沸腾换热的影响与一个干度值有关。当干度小于此值时,沸腾换热系数会随着热流密度及饱和压力增大而增大;而当干度大于此值时,沸腾换热系数随着干度增大而急剧下降,热流密度和饱和压力对换热的影响较小;该干度值会随着热流密度或饱和压力增大而逐渐变小。质量流率对沸腾换热的影响与热流密度有关,随着热流密度增大,质量流率的影响趋向大干度区域。通过分析各参数对沸腾换热的影响,建立了一个预测试验工况下微小尺寸锯齿扁管的沸腾换热系数计算经验公式。     

辐射换热对平板气膜冷却性能影响

为了分析辐射换热对平板气膜冷却性能的影响,分别对不考虑辐射换热(耦合计算)与考虑辐射换热两种条件下的平板隔热屏进行了三维流热耦合数值模拟研究,并与绝热壁(不考虑隔热屏固壁导热)的计算结果进行了对比。辐射换热采用离散坐标法。得到了3种不同主/次流总温比(Rt)条件下气膜冷却效果、流场、单位面积冷流体热负荷以及流量系数的对比结果与变化规律。结果表明:气膜冷却效果沿流向逐渐降低,且随总温比的增加而降低;在展向上气膜冷却效果呈现中间高两边低的分布规律,最大与最小相对值在绝热壁条件下达到最大,为94.5%,辐射换热次之,为13.5%,不考虑辐射换热时最小,为9.8%。与不考虑辐射换热结果相比,辐射换热对气膜冷却效果的影响在流动方向逐渐变大,气膜孔附近展向温度梯度增大,冷流体热负荷增加了92.8%,二者计算的流量系数相差不大,为1.1%,与绝热壁计算结果相比,流量系数减小了13.1%。随着总温比增加流量系数减小,最大值与最小值相差不大,为1.1%。     

Refinements in the data analysis of VIRTIS-M-IR Venus nightside spectra

The successful long-duration radiation measurements performed by the VIRTIS instrument aboard ESA’s Venus Express spacecraft have provided an excellent collection of atmospheric and surface data that stand out due to their high temporal and spatial coverage of the planet and due to a high diversity of measurement and environmental conditions.     

A low-thrust transfer between the Earth–Moon and Sun–Earth systems based on invariant manifolds

A low-energy, low-thrust transfer between two halo orbits associated with two coupled three-body systems is studied in this paper. The transfer is composed of a ballistic departure, a ballistic insertion and a powered phase using low-thrust propulsion to connect these two trajectories. The ballistic departure and insertion are computed by constructing the unstable and stable invariant manifolds of the corresponding halo orbits, and a complete low-energy transfer based on the patched invariant manifolds is optimized using the particle swarm optimization (PSO) algorithm on the criterion of smallest velocity discontinuity and limited position discontinuity (less than 1 km). Then, the result is expropriated as the boundary conditions for the subsequent low-thrust trajectory design. The fuel-optimal problem is formulated using the calculus of variations and Pontryagin's Maximum Principle in a complete four-body dynamical environment. Then, a typical bang–bang control is derived and solved using the indirect method combined with a homotopic technique. The contributions of the present work mainly consist of two points. Firstly, the global search method proposed in this paper is simply handled using the PSO algorithm, a number of feasible solutions in a fairly wide range can be delivered without a priori or perfect knowledge of the transfers. Secondly, the indirect optimization method is used in the low-thrust trajectory design and the derivations of the first-order necessary conditions are simplified with a modified controlled, restricted four-body model.     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

水气动量交换的实验研究

在风浪槽中进行水气动量交换实验，测量了不同风速和风区下的波浪及空气湍流流场。测量数据表明水面上风速分布符合对数律，水气界面附近在小范围的动量交换常通量层。阻力系数ＣＤ随风速增加线性增长，随波龄增加而减小。这一趋向与理论分析及外海帝测结果一致。对风浪发展过程中波浪和空气湍流谱结构的分析证明了水气运动的耦合关系。