L-band nighttime scintillations at the northern edge of the EIA along 95°E during the ascending half of the solar cycle 24

The characteristics of nighttime ionospheric scintillations measured at the L-band frequency of 1.575 GHz over Dibrugarh (27.5°N, 95°E, MLAT ～ 17°N, 43° dip) during the ascending half of the solar cycle 24 from 2010 to 2014 have been investigated and the results are presented in this paper. The measurement location is within or outside the zone of influence of the equatorial ionization anomaly depending on solar and geomagnetic activity. Maximum scintillation is observed in the equinoxes irrespective of solar activity with clear asymmetry between March and September. The occurrence frequency in the solstices shifts from minimum in the June solstice in low solar activity to a minimum in the December solstice in high solar activity years. A significant positive correlation of occurrence of scintillations in the June solstice with solar activity has been observed. However, earlier reports from the Indian zone (～75°E) indicate negative or no correlation of scintillation in June solstice with solar activity. Scintillations activity/occurrence in solstices indicates a clear positive correlation with Es recorded simultaneously by a collocated Ionosonde. In equinoxes, maximum scintillations occur in the pre-midnight hours while in solstices the occurrence frequency peaks just after sunset. The incidence of strong scintillations (S₄ ≥ 0.4) increases with increase in solar activity. Strong (S₄ ≥ 0.4) ionospheric scintillations accompanied by TEC depletions in the pre-midnight period is attributed to equatorial irregularities whereas the dusk period scintillations are related to the sporadic-E activity. Present results thus indicate that the current location at the northern edge of the EIA behaves as low as well as mid-latitude location.     

Thrusting maneuver control of a small spacecraft via only gimbaled-thruster scheme

The thrust vector control (TVC) scheme is a powerful method in spacecraft attitude control. Since the control of a small spacecraft is being studied here, a solid rocket motor (SRM) should be used instead of a liquid propellant motor. Among the TVC methods, gimbaled-TVC as an efficient method is employed in this paper. The spacecraft structure is composed of a body and a gimbaled-SRM where common attitude control systems such as reaction control system (RCS) and spin-stabilization are not presented. A nonlinear two-body model is considered for the characterization of the gimbaled-thruster spacecraft where, the only control input is provided by a gimbal actuator. The attitude of the spacecraft is affected by a large exogenous disturbance torque which is generated by a thrust vector misalignment from the center of mass (C.M). A linear control law is designed to stabilize the spacecraft attitude while rejecting the mentioned disturbance torque. A semi-analytical formulation of the region of attraction (RoA) is developed to ensure the local stability and fast convergence of the nonlinear closed-loop system. Simulation results of the 3D maneuvers are included to show the applicability of this method for use in a small spacecraft.     

冷板流道结构优化及其钎焊技术

针对航天航空领域中集成电子设备出现的热流密度过高所带来的高效散热技术冷板设计问题与结构制造难题,提出了一种流道设计优化与结构钎焊技术。利用Flotherm热仿真分析软件对导流和结构等进行优化,完成了高效率散热结构设计。同时,对设计的窄流道结构带来的焊接质量问题,进行了钎料和焊接压力参数优化。结果表明:与传统S型流道冷板相比,采用片状导流结构和串并联混合结构的冷板热源温度降低了15℃,并将均温性控制在1.2℃以内。采用控制钎料厚度和工装压力的方法,降低了窄筋流道堵塞和焊接变形趋势。     

直升机抛射物体平衡及稳定性分析

基于部件级建模理论建立了建立直升机-外挂装置系统六自由度飞行动力学模型。对所建模型进行了配平计算，与参考数据进行了对比。计算分析了不同速度下采用不同方式抛射物体时直升机的稳定性。结果表明，单侧抛射由于反冲力不对称，抛射物体对于直升机的滚转角和横向周期变距有显著的影响；随飞行速度增大，抛射物体对于直升机横向荷兰滚模态稳定性影响增大，当前飞速度达到50m/s以上时，荷兰滚模态演变为两个发散的非周期模态，稳定性明显变差，直升机应在较低速度下抛射物体。      

运输机机翼平面参数快速优化方法

提出了一套机翼平面参数快速优化方法。新方法通过改变优化思路,简化计算模型,合理选择计算方法,有效地提高了优化效率。简要介绍参数优化思想与流程控制,重点阐述优化程序的气动、重量与性能计算模块的算法。以某运输机为算例,优化结果与资料数据吻合,验证了新方法的正确性。     

大型空间环境模拟器热沉气氮调温系统设计与实现

文章结合某型号航天器对调温热沉试验需求,对国内外气氮调温系统进行分析调研,对某空间环境模拟器进行了气氮调温系统流程设计,对影响系统的关键参数如气氮流量、液氮体积流量及有关供气供热管径等进行分析研究和设计实施,并进行了系统调试。调试结果表明,热沉温度均匀性达到±5℃,升/降温速率均达到或超过1℃/min,满足相应的型号试验要求。     

Passive localization by a single moving observer using TOA only with unknown SRI: Observability analysis and algorithm

Passive localization by a single moving observer using Time of Arrival (TOA) only with an unknown Signal Repetition Interval (SRI) is investigated in this paper. Observability analysis is performed first. The observability condition for uniquely determining the emitter position and SRI is derived. The conditional Cramer-Rao Lower Bound (CRLB) is also analyzed. It is found that the ambiguity of the SRI integer of the first TOA does not affect the theoretical estimation precision of the emitter position and SRI. A Reference-Fixed Differential TOA (RFDTOA)-based Iterative Maximum Likelihood Estimator (IMLE) is proposed, which only needs O(M) computational operations. Theoretical analysis and simulation results show that the Mean Square Error (MSE) of the proposed algorithm could attain the CRLB with moderate Gaussian measurement noise.     

多故障转子-滚动轴承系统的动力学特性

为深入研究多故障转子-滚动轴承系统的机理,充分考虑了旋转部件的扭矩、剪切力、转动惯量及陀螺力矩等效应,采用Timoshenko梁单元和转盘单元建立了转子的有限元模型,集成了滚动轴承动力学模型,及不平衡、不对中、碰摩、裂纹及松动等故障模型,得到了多故障转子-滚动轴承系统的动力学方程。采用变步长龙格库塔法,获得了转子-滚动轴承系统的位移响应,研究了系统位移响应随转速变化的分岔图、庞加莱截面,以及故障特征处的时域波形图、轴心轨迹图、相平面图和频谱图,探究了多故障转子-滚动轴承系统的故障特征及其动力学特性和规律。仿真分析结果表明：多故障转子-滚动轴承系统在运行过程中存在周期运动,拟周期运动和复杂的类混沌运动等丰富的非线性行为,且在各非线性行为转速区间内,会呈现不平衡、不对中、碰摩、裂纹和松动等单一故障或耦合故障的特征和现象。     

神经网络模型在压气机通流特性分析中的应用

为了解决通流特性分析程序中原始模型对压气机性能预测精度不足的问题,提高压气机通流特性分析过程的可靠性,基于对大量多圆弧叶栅的数值模拟结果建立了压气机叶栅性能数据库,并以该数据库为依托,采用神经网络建模方法建立了压气机叶栅基准损失系数和基准落后角模型。结果显示:两模型对叶栅基准损失系数和基准落后角的预测精度均满足工程应用要求,其精度分别为±0.002和±1°。在对采用神经网络模型的通流特性分析程序校验过程中发现,其无论对压气机整机性能还是对流动细节的预测精度上都获得了显著提高,尤其是在主流区。此外从压气机整体特性上看,基准损失系数和基准落后角精度的提高对非设计工况损失系数和落后角的预测精度影响是积极的。      

Collaborative image compression and classification with multi-task learning for visual Internet of Things

Widespread deployment of the Internet of Things(Io T) has changed the way that network services are developed, deployed, and operated. Most onboard advanced Io T devices are equipped with visual sensors that form the so-called visual Io T. Typically, the sender would compress images, and then through the communication network, the receiver would decode images, and then analyze the images for applications. However, image compression and semantic inference are generally conducted separately, and t...