机匣处理作用下高负荷轴流压气机转/静子匹配设计研究

为了探索机匣处理作用下转/静子的轴向匹配方法以进一步提高压气机级的失速裕度,研究了静子的叶型安装角及"弯"、"掠"规律对压气机性能的影响,针对机匣处理与优化静子的组合结构进行了非定常数值模拟,阐述了该结构的扩稳机理以及压气机新的失速机制。研究结果表明,在机匣处理作用下,静子成为压气机失速的触发因素,通过对静子叶型安装角及"弯"、"掠"规律的优化均可进一步提高压气机级的失速裕度,其中改变静子"弯"型对压气机级失速裕度的改善最大。组合应用机匣处理与尖部反弯根部正弯静子后,压气机效率基本不变,失速裕度提升了80.2%,较单独使用机匣处理提升30.9%。在该组合结构作用下,压气机的失速由静子触发,静子叶根吸力面在激波作用下发生附面层分离,且与轮毂表面附面层相互作用形成角区涡,接近失速边界时,静子叶根形成"前缘溢流,尾缘反流"现象,造成静子通道的大范围堵塞,诱发压气机失速。压气机级的扩稳应充分考虑机匣处理的影响,对静子进行优化设计。     

目的论视角下服装品牌的翻译

随着全球化飞速发展,海内外服装贸易竞争日益激烈,服装品牌的译名日益显示出其重要性。以服装类品牌为研究对象,旨在探讨目的论下的服装品牌的翻译策略。目的论认为,目的原则是翻译中的首要原则。经分析发现,为使译名达到传达信息、传递美感或呼唤消费的目的,译者在翻译时应灵活运用音译、直译、意译、音意译几种译法,创造出达意传神、刺激消费的译名。     

论荀子的“勇”

荀子根据"勇"与"义"、"利"的关系提出了"狗彘之勇"、"贾盗之勇"、"小人之勇"、"士君子之勇",只有"士君子之勇"是值得提倡的。荀子还将"勇"划分为上勇、中勇、下勇,认为只有上勇才是真正的大勇。真正的勇并不是先天具有的,是后天"人为"的结果,需要重视礼的作用,树立重义轻利的求荣避辱观念,通过师法不断培养才能形成。     

组合临界流文丘里喷嘴空气流量测量方法高空舱应用分析

为满足发动机高空试验低流速进气条件下空气流量精确测量,减小进气导管气流附面层影响,弱化空气流量测量与被试发动机相关性。分析了单件/组合临界流文丘里喷嘴的工作特性,给出了组合临界流文丘里喷嘴(ACFVN)空气流量计算方法,依据给定试验发动机和高空舱尺寸设计了临界流文丘里喷嘴组合结构,得到了组合临界流文丘里喷嘴在高空舱应用的控制方法和测试布局。采用小尺寸喷嘴对组合喷嘴设计和应用方法进行了验证,结果表明:采用打开/关闭喷嘴数量和调节进气压力两种组合方式在高空舱内应用方法可行,测试布局满足测量要求,下游发动机进口截面气流紊流度优于0.3%,满足发动机高空模拟试验要求。      

利用增量相位和星光仰角增强XNAV

针对X射线脉冲星导航系统(XNAV)中过程噪声统计特性难以准确获取，对其不当假设导致滤波器估计性能不佳的问题，提出基于自适应差分卡尔曼滤波器(ADDF)的多信息融合算法。为了降低导航误差，在传统脉冲星计时观测的基础上，增加恒星星光仰角及两个时刻间的相位增量观测量，共同增强XNAV。首先，分别建立计时观测模型、相位增量模型及星光仰角模型；然后将多信息测量模型集成到卫星轨道动力学方程中，以建立ADDF滤波模型；最后对所提方法进行仿真验证。实验结果表明，在相同的初始状态和初始噪声误差条件下，与传统X射线脉冲星导航算法相比，多信息融合算法能将导航位置估计精度提高70%以上，位置估计误差降低到 200 m 左右，速度估计精度提高40%以上，且ADDF性能优于无迹卡尔曼滤波器。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

平台式重力仪航空重力测量数据后处理技术研究

针对航空重力测量对数据后处理的要求,结合平台式重力仪系统的组成与工作原理,在重力异常信号的频域特征基础上,设计出一套有严格频域规范的航空重力数据后处理流程,并对某海域实测数据进行了处理。结果表明,重力异常值内符合精度为12条东西测线达到0.43mGal/140s和0.84mGal/100s,4条南北测线达到0.39mGal/140s和0.79mGal/100s;以同测线GT-2A单次测量结果为标准值统计标准差,12条东西测线为0.72mGal/140s和0.98mGal/100s,4条南北测线为1.41mGal/140s和1.53mGal/100s。结果表明,设计的航空重力测量数据后处理方法可以实现重力异常信号的高精度提取。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

耦合热、动载荷的超超临界汽轮机迷宫密封动力特性

密封汽流激振严重影响超超临界汽轮机的安全运行,采用DEFINE_CG_MOTION和DEFINE_PROFILE控制宏建立转子的涡动方程,通过Workbench流固耦合方法计算热、动载荷下密封齿形变,根据快速傅里叶变化得到机组运行时的密封动力特性,并对转子稳定性进行分析。结果表明:蒸汽可导致密封齿膨胀变形,温度对密封齿长度变化影响可达1%~1.5%,压力和离心作用对其影响较小。热、动载荷使迷宫密封直接刚度减小,直接阻尼先增加后减小,交叉刚度先减小后增加,动力系数的最大变化为原来的2倍。35~55 Hz内转子稳定裕度急剧下降,转子对密封汽流激振更敏感。热、动载荷引起的压力波动集中在低频范围,密封周向压力波动可增高18.5 kPa。密封高压区的压力波幅剧增是汽流激振显著的主要原因。      

变体辅助的无人机栖落机动模糊控制设计

无人机（Unmanned aerial vehicle， UAV）的栖落机动是一种大幅度的俯仰运动，易引起升降舵操纵力矩饱和。本文以变体方式增强无人机的俯仰操纵能力，并研究其对应的控制设计方法。首先对栖落机动建立了纵向动力学模型，并通过采用轨迹线性化和张量积变换方法转换得到T-S模糊模型。基于Lyapunov稳定理论和平方和方法，设计了满足控制输入约束的栖落机动多项式模糊控制器。对非变体与变体下的栖落机动控制过程进行了仿真，结果验证了控制律的有效性，并且表明变体辅助的无人机具有更强的操纵性能，能提高栖落机动中升降舵的抗饱和能力。