超长大直径钻孔灌注桩桩端承载力研究

阐述了超长大直径钻孔灌注桩桩端承载力的影响因素,包括施工工艺、深度效应和尺寸效应等。分析和对比了目前国内常用的各规范所采用的计算方法。文中算例的计算结果表明,对于同等条件的桩,各规范的计算结果相差较大。采用自平衡试桩法获得了几个重大工程的超长大直径钻孔灌注桩的桩端承载力的实测值。将工程实例的测试结果与各规范的计算结果进行对比,证实了目前规范的计算方法不尽合理。目前各规范中桩端承载力的计算方法是在针对小直径的中短桩的研究基础上建立的。如今,大型桥梁工程中普遍采用超长大直径钻孔灌注桩的情况下,对其桩端承载力的计算应当进行相应的调整,使设计更为合理。     

桩后压浆灌注桩的技术分析

对桩后压浆灌注柱的工作原理、施工工艺及控制参数进行了分析，并提出了该技术的适用条件及技术优势。     

生物组织光学参数：优化散射系数（μ’s）的实时在位测定

利用了一套特殊设计光纤探头组成的稳定态光纤光谱仪测试生物组织的光学参数，从悬乳液(Intralpid)与模拟胶(Phantom)实验推导出优化散射系数(Reduced scattering coeffcient：μ’s)近红外谱测量经验公式。测量反射系数就可以计算出优化散射系数谱。计算结果用模拟胶作了验证，并对大鼠脑组织μ’s进行了实时在位测量，从而得到了一种μ’s在位测量的有效方法。     

直流电机网络控制系统仿真

对直流电机网络闭环控制系统进行仿真分析,根据电机网络闭环控制系统原理建立仿真模型。对具有数据丢包的直流电机网络伺服控制系统输出响应特性进行仿真,比较系统分别采用PI控制及增益,可调PI控制方式时的输出特性。结果表明,相比常规PI控制增益可调PI控制方法在网络环境下具有更好的控制特性。该研究为网络伺服控制技术提供可靠的参考依据。     

外翼上壁板根部连接形式对飞机承载能力的影响研究

在飞机结构设计中,外翼上壁板根部连接处结构形式对飞机的传力、变形、承载能力具有重要影响.通过对3种不同形式的上壁板根部连接方案进行压缩试验,研究各方案的承载能力、破坏方式.通过三维有限元方法,计算了连接部位的主要螺钉所分配的载荷,研究了长桁根部斜角对结构屈服载荷的影响,得到了最优的选型方案.     

Air route network optimization in fragmented airspace based on cellular automata

Air route network optimization,one of the essential parts of the airspace planning,is an effective way to optimize airspace resources,increase airspace capacity,and alleviate air traffic con gestion.However,little has been done on the optimization of air route network in the fragmented airspace caused by prohibited,restricted,and dangerous areas (PRDs).In this paper,an air route network optimization model is developed with the total operational cost as the objective function while airspace restriction,air route network capacity,and non-straight-line factors (NSLF) are taken as major constraints.A square grid cellular space,Moore neighbors,a fixed boundary,together with a set of rules for solving the route network optimization model are designed based on cellular automata.The empirical traffic of airports with the largest traffic volume in each of the 9 flight information regions in mainland China is collected as the origin-destination (OD) air port pair demands.Based on traffic patterns,the model generates 35 air routes which successfully avoids 144 PRDs.Compared with the current air route network structure,the number of nodes decreases by 41.67％,while the total length of flight segments and air routes drop by 32.03％ and 5.82％ respectively.The NSLF decreases by 5.82％ with changes in the total length of the air route network.More importantly,the total operational cost of the whole network decreases by 6.22％.The computational results show the potential benefits of the model and the advantage of the algorithm.Optimization of air route network can significantly reduce operational cost while ensuring operation safety.     

热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

基于改进准则法的复合壳阻尼结构拓扑减振动力学优化

针对复合壳阻尼结构的拓扑减振优化问题，以约束阻尼层的有限单元为设计变量，采用体积比、模态频率和振型为优化约束条件，构建以多模态权重系数的结构模态损耗因子数值关系为优化目标函数的拓扑减振优化模型。为了拓展优化目标灵敏度具有不局限于某一变密度法插值模型的形式，推导了数值表达式的一般函数式。动力学优化中优化目标灵敏度正、负数集共存，使得非凸性的目标函数设计变量出现负值或优化函数寻优于局部极值点。为此，推导出复合壳阻尼结构的全域灵敏度改进优化准则法迭代格，以确保每次迭代域均为全域设计变量集。结合有限单元法编程实现了复合壳阻尼结构改进准则法，并对复合壳结构进行拓扑减振优化分析。结果表明：在敷设体积减为全覆盖的50%时，复合壳结构的模态损耗因子增减偏差为10%，具有提升减振的轻量化设计目的；各阶目标函数和拓扑构型所需的迭代次数少，中间密度区域较小，多阶优于单阶模态优化函数，易于获得全域寻优的有效减振。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

谐振电路中品质因数的计算方法

从品质因数的原始定义出发,分别计算出简单RLC串、并联电路的品质因数,得到两个结论,并将其推广,提出了两种简单的计算品质因数的方法,最后通过求解一个实际的LC并联谐振电路的品质因数得到验证。