涡扇发动机闭环控制系统设计仿真平台

航空发动机闭环控制系统的设计过程复杂且环节繁多,如果通过某平台综合多个设计过程,必然可以简化流程,提高效率.在总结国内外相关文献的基础上,针对民用涡扇发动机,在Matlab/Simulink下,利用模块化方法构建包含稳态控制器、过渡态控制器以及极限保护器的涡扇发动机闭环控制系统仿真平台,并对其进行仿真测试和硬件在回路实验.结果表明,所构建的仿真平台满足控制系统的性能和实时性要求,具有良好的工程适用性.     

AZ31B镁合金大应变循环变形行为研究

为了研究AZ31B镁合金在大应变幅条件下的变形机制,开展了该合金在7.嬲应变幅条件下的循环行为研究.结果表明:在拉伸阶段的最大应力值随着循环周次的增加而减小,而在压缩过程中的最大应力值随着循环周次的增加而增大,在整个循环过程中材料呈现循环应变硬化特性,拉应力是导致循环应变硬化的主要原因;随着循环周次增加,滞回曲线的不对称性基本不变.真应力-真应变滞回曲线在卸载和反向拉伸阶段出现3个拐点.在压缩过程中发生{10-12}孪生,反向拉伸过程发生去孪生行为,包申格效应对去孪生行为具有较大影响.研究表明:孪生-去孪生是大应变幅循环变形的主要变形机制;对拉伸、反向压缩过程的变形特征及机制的分析,可为低周疲劳行为的研究提供参考.     

卫星用两种单相流体回路方案对比研究

单相流体回路系统是航天器主动热控技术中的一种重要方式。文章概述了流体回路的工作原理及理论基础，总结了单相流体回路的设计思路，结合某卫星型号，设计了两种流体回路方案，在SINDA／FLUINT中建立数值仿真模型进行分析计算，并比较了两种方案的应用性能。结果显示，将单相流体回路系统应用于卫星，可取得较好的控温效果。     

一种改进的防空导弹侧向回路稳定控制结构分析

基于复合稳定控制结构,对某防空导弹侧向回路过载反馈通道的结构进行了改进。基于理论分析,结合工程应用实际进行了数学仿真验证。结果表明:在保持足够稳定裕度的前提下,改进结构的系统快速性好,鲁棒性更优。     

烧结双多孔介质中沸腾换热的实验研究

对由铜粉烧结而成的三种双多孔介质结构进行了沸腾换热的实验。为了便于比较，同时对两种单多孔介质进行了沸腾换热实验。结果发现：当双多孔介质的微孔径和单多孔介质的孔径相同时，双多孔介质的换热系数和临界热流密度比单多孔介质高得多；对于同样微孔径的双多孔介质，存在最佳的粗孔径，其换热系数和临界热流密度最大；当逆静水压头减小的时候，换热系数和临界热流密度增加。     

可展开式辐射器热控对航天器轨道调整的适应性分析

为提高航天器热控系统对轨道调整的适应能力，本文研究了与流体回路耦合的可展开式辐射器热控方案在不同轨道高度下的热控性能，分析了不同轨道高度时辐射器面临的热环境的影响，在不同轨道高度下比较了固定辐射器与可展开辐射器的热控特性。结果表明，随着辐射器展开角度的变化，辐射器吸收的空间热流随之发生变化，从而对热控系统的散热能力带来直接影响，调节辐射器的角度可以扩大其对外散热能力。在工程应用中，基于热控流体回路，通过调节可展开式辐射器的展开角度，可以有效提高航天器的轨道热适应能力。     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

基于极大似然估计器的GNSS矢量跟踪算法

矢量跟踪是一种将全球导航卫星系统(GNSS)接收机的信号跟踪与导航解算融为一体的跟踪算法。传统的基于矢量延迟/频率锁定环(VDFLL)的跟踪算法普遍采用延迟锁定环(DLL)和锁频环(FLL)鉴别器计算伪距和伪距率偏差观测量,由于锁频环鉴别器存在近似误差和一步延迟效应,在高动态环境下容易造成环路失锁。从直接估计卫星信号特征参数的角度出发,基于中频信号模型构建码相位和载波多普勒的极大似然代价函数,采用非迭代估计算法得到各通道码相位和多普勒频移的估计偏差,转换为卡尔曼滤波器的观测矢量,提出一种基于极大似然估计器(MLE)的矢量跟踪算法。理论分析和仿真结果表明:新算法结合了极大似然估计和矢量跟踪的优点,克服了FLL的延迟效应,与基于VDFLL的矢量环路相比,高动态环境下的跟踪稳定性更好,可以对被遮挡的卫星保持持续的跟踪。     

主动冷却燃烧室燃烧与传热耦合过程迭代分析设计方法

为了对主动冷却超燃冲压发动机进行研究与设计,采用实验与计算相结合的方法,对主动冷却超燃冲压发动机燃烧室内传热与燃烧的耦合过程进行了分析。该方法采用燃烧室静压分布的测量值作为输入条件,开展燃气-结构-燃料耦合传热分析,获得经过冷却系统后燃料的状态参数;将燃料的状态参数作为实验参数,开展直联式超声速燃烧实验,得到新的静压分布,如此反复迭代,直至燃料状态不再变化,最终确定主动冷却燃烧室的各种传热与燃烧特性参数。利用该分析方法,初步开展了不同飞行马赫数条件下主动冷却燃烧室闭环运行状态研究,得到了冷却煤油温度与燃烧室壁温同飞行马赫数的关系。     

Application in prestiction friction compensation for angular velocity loop of inertially stabilized platforms

To overcome the influence of the nonlinear friction on the gimbaled servo-system of an inertial stabilized platforms(ISPs) with DC motor direct-drive, the methods of modeling and compensation of the nonlinear friction are proposed. Firstly, the inapplicability of LuGre model when trying to interpret the backward angular displacement in the prestiction regime is observed experimentally and the reason is deduced theoretically. Then, based on the dynamic model of direct-drive ISPs, a modified LuGre model is proposed to describe the characteristic of the friction in the prestiction regime. Furthermore, the state switch condition of the three friction regimes including presliding, gross sliding and prestiction is presented. Finally, a composite compensation controller including a nonlinear friction observer and a feedforward compensator based on the novel LuGre model is designed to restrain the nonlinear friction and to improve the control precision. Experimental results indicate that compared with those of the conventional proportion–integration–differentiation(PID) control method and the PID plus LuGre model-based friction compensation method, the dwell-time has decreased from 0.2 s to almost 0 s, the position error decreased to 86.7%and the peak-to-peak value of position error decreased to 80% after the novel compensation controller is added. It concludes that the composite compensation controller can greatly improve the control precision of the dynamic sealed ISPs.