全文获取类型
收费全文 | 3043篇 |
免费 | 839篇 |
国内免费 | 650篇 |
专业分类
航空 | 2928篇 |
航天技术 | 443篇 |
综合类 | 362篇 |
航天 | 799篇 |
出版年
2024年 | 11篇 |
2023年 | 66篇 |
2022年 | 98篇 |
2021年 | 140篇 |
2020年 | 128篇 |
2019年 | 133篇 |
2018年 | 122篇 |
2017年 | 202篇 |
2016年 | 162篇 |
2015年 | 147篇 |
2014年 | 225篇 |
2013年 | 174篇 |
2012年 | 225篇 |
2011年 | 234篇 |
2010年 | 201篇 |
2009年 | 218篇 |
2008年 | 202篇 |
2007年 | 279篇 |
2006年 | 233篇 |
2005年 | 199篇 |
2004年 | 148篇 |
2003年 | 154篇 |
2002年 | 124篇 |
2001年 | 118篇 |
2000年 | 141篇 |
1999年 | 76篇 |
1998年 | 76篇 |
1997年 | 60篇 |
1996年 | 39篇 |
1995年 | 34篇 |
1994年 | 36篇 |
1993年 | 31篇 |
1992年 | 27篇 |
1991年 | 21篇 |
1990年 | 12篇 |
1989年 | 18篇 |
1988年 | 8篇 |
1987年 | 10篇 |
排序方式: 共有4532条查询结果,搜索用时 15 毫秒
101.
102.
LI Jian-liang XIONG Dang-sheng* WAN Yi Department of Materials Science Engineering Nanjing University of Science Technology Nanjing China 《中国航空学报》2006,19(Z1)
Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent. 相似文献
103.
104.
105.
本文叙述了金属基复合材料热循环损伤的动态共振检测方法,利用该方法对B/Al、SiCf/Al和C/Mg等单向排列金属基复合热循环损伤进行了检测,得出一些结果,并进行了讨论。 相似文献
106.
介绍一种新机研制计划管理和决策支持系统的总体设计方案及其实现的具体措施。详细介绍了几个主要模块的设计思想。 相似文献
107.
介绍了一种新颖的光回波损耗测量方法.使用该方法测量光纤器件的回波损耗不但具有小的测量不确定度,而且有效地解决了光回波损耗参数的量值溯源问题. 相似文献
108.
张绪虎%胡欣华%关盛勇%汪翔%杨盛良 《宇航材料工艺》2001,31(2):48-55
对经300℃、500℃高温热暴露的B/Al(LF6)复合材料的力学性能进行了研究,实验结果表明材料在300℃下热暴露时,性能下降速度较慢,100h后强度保留率约为76%,延伸率保留率为74%。而在500℃下热暴露时,5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜(TEM)及扫描电镜(SEM)对固态热压制造态和主温热暴露的界面状况进行了分析,认为界面反应是造成B/Al复合材料力学性能下降的主要原因。 相似文献
109.
随着计算机网络技术的发展和普及,目前出现了以单片机技术和以太网技术为核心的嵌入式网关技术,采用嵌入网关技术,可在局域网环境下采用TCP/IP协议实现门禁控制控制器同后台服务器的数据交换。其优点是技术先进、数据传输速度高、工程成本低、可靠性和安全性高。在论述了嵌入式网关工作原理的基础上,重点讨论了嵌入式网关中的门禁控制器的应用问题。 相似文献
110.
文思维%肖加余%曾竟成%杨孚标%张昌天 《宇航材料工艺》2007,37(3):67-70
设计了一种单纤维拔出试样制备方法,分析了单根硼纤维拔出特性;同时采用该方法分别测试了四种硼纤维/环氧复合材料界面剪切强度。固化剂采用异佛尔酮二胺(IPDA)的硼纤维/环氧复合材料界面剪切强度比采用二乙烯三胺(DETA)的提高了44.7%;采用液体丁腈橡胶(LNBR)改性环氧树脂的硼纤维/环氧复合材料界面剪切强度提高了97.7%~135%。 相似文献