固溶时效处理对高强高韧钛合金显微组织与力学性能的影响

对固溶时效处理后的高强高韧钛合金初生α相的体积分数、尺寸,次生α相的体积分数和α_s/β相界面密度等显微组织特征进行了定量表征和统计分析,探讨了随着固溶温度的变化,高强高韧钛合金显微组织与其力学性能间的相关性.结果表明:在α+β两相区固溶时效处理,随着固溶温度的升高,合金初生α相的体积分数降低,相尺寸先降低后略有升高,次生α相的体积分数升高,α_s/β相界面密度先升高后降低.初生α相的体积分数与伸长率、静力韧度和裂纹形成功正相关,α_s/β相界面密度与合金屈服强度成正相关.      

铝合金薄板零件橡皮囊成形屈曲分析与实验

为了抑制铝合金薄板类零件在橡皮囊成形后出现屈曲的缺陷,采用薄板屈曲微分方程对零件成形后的屈曲进行理论分析,并通过橡皮囊成形实验研究自然时效时间和成形压力对屈曲缺陷的影响。理论分析结果表明：零件法兰屈曲波数与其内外径比有关,通过改变法兰宽度进行实验验证,实验结果与理论分析结果相符;而成形实验结果表明,屈曲缺陷高度随板料自然时效时间的增加而增加,随成形压力的增加而减少。因此,理论分析结果有效,并且可通过减少淬火后成形时间和增加成形压力来抑制屈曲缺陷。     

热色液晶标定和使用的影响因素

在全面地分析热色液晶测量方法的基础上,实验研究了热色液晶标定和使用的主要影响因素.保持频闪和相机的相对位置以及两者距拍摄窗口的距离一致,在同一色调值下,拍摄方式(无/有拍摄窗口)、有机玻璃拍摄窗厚度、热力方向(加热/冷却)和热色液晶老化分别产生最大约0.5℃,0.2℃,0.26℃和1.2℃的温度差异.转静间隙不影响热色液晶的显色特性.温度与色调的关系主要与频闪仪的发光介质有关.      

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

DZ125定向凝固高温合金长期时效后的显微组织和超高周疲劳行为

 选用950 ℃时效温度,对DZ125定向凝固高温合金进行了500、1 000、1 500 h的长期时效。利用超声疲劳试验机测试了合金的超高周疲劳性能。采用扫描电子显微镜、透射电子显微镜和电子背散射衍射(EBSD)研究了合金的显微组织和超高周疲劳行为。结果表明:长期时效对DZ125合金的组织稍有影响,长期时效后合金的点阵错配度降低,随着时效时间的延长,γ'相聚集长大更加明显,未出现拓扑密排相(TCP)等有害相;长期时效对DZ125合金的超高周疲劳性能稍有影响,随着时效时间的延长,疲劳性能呈下降趋势,疲劳断口较平整,裂纹起源于试样的表面,在超高周疲劳后合金的晶粒发生了小幅度旋转。     

Twaron纤维的新型化学活化方法

以傅瑞德-克拉夫茨(Friedel-Crafts)反应为基础,活化处理Twaron纤维的惰性表面。对经过活化处理的Twaron纤维进行了单丝拔出(SFP)、X射线衍射(XRD)、扫描电镜(SEM)、红外图谱(FTIR)、表面电子能谱(XPS),以及表面自由能等测试。测试结果显示,经过活化处理后,Twaron纤维表面因环氧基团的接枝而使表面自由能显著增加;纤维表面的结晶结构未发生显著改变,纤维的本体强度未降低;相对应的环氧树脂基复合材料的单丝拔出强度提高了约50%。     

ZnO透明导电薄膜制备及紫外辐照处理特性研究

ZnO作为一种典型的透明导电氧化物（Transparent conductive oxide,TCO）材料,具有同氧化铟锡(Indium tin oxide,ITO)相比拟的光电性能,其原料丰富、绿色环保、易于制备、生成成本低等优点使ZnO成为最有希望替代ITO的材料。本文以玻璃为衬底,利用量子点种子层作为缓冲层,采用传统水热方法制备了低成本ZnO透明导电薄膜,采用特殊的紫外光辐照工艺对薄膜进行后处理,探索薄膜生长参数和紫外光辐照处理工艺对其透光率和导电性的影响。结果表明,紫外辐照处理不影响薄膜的透光性能,而使材料的方块电阻降低3个数量级,数值从没处理时的1.5×105 Ω/□降低到 150 Ω/□,极大地提高了薄膜的电导率,为ZnO薄膜材料电导率的提高提供了一个简单高效的途径。     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

橡胶密封性能多元双方差回归分析方法

建立了橡胶密封材料压缩永久变形的加速老化模型及其多元双方差回归分析方法,给出了密封性能的回归方程及其高置信水平、高可靠度的单侧置信上限曲线,并建立了可靠贮存寿命、贮存可靠度的计算方法.橡胶密封性能的多元双方差回归模型包含与时间有关的过程自变量和与温度有关的状态自变量,可以将不同温度下的加速老化试验数据作为一个整体进行回归分析,充分利用了不同时刻压缩永久变形间的纵向信息,具有信息量大、精度高且计算简单的特点.      

均匀化处理对TiAl 合金铸造组织的影响

研究了均匀化处理对两种含B的铸造TiAl合金铸造组织的影响。研究发现1 370℃/5 min/OQ+1150℃/6 h/AC均匀化热处理能有效消除B2相,将b稳定化元素固溶到基体中,实现成分均匀化;1 370℃/5 min/OQ+1 150℃/24 h/AC均匀化热处理后可使粗大的铸造片层组织分解转变为细晶近g组织,平均晶粒直径50mm。