L8飞机从风洞到飞行的抖振相关性研究

介绍了Ｌ８飞机抖振边界修正结果，并与同类飞机Ｌ２９飞行抖振边界进行了比较；给出了Ｌ８飞机抖振边和轻度抖振边界预测值。同时将预测抖振边界和试飞得到的抖振边界作了比较。     

混合移频静刚度法和直接扰动迭代法

本文对混合移频动柔度法的失代式进行等价变换，从而得到一个“变种”，该变种不包含混合移频系统的动柔度式F^△（λ*），这便消除了F^△（λ*）带来的近似性，另外，对直接扰动法也进行等价变换，引出可以省时地用于许多特征向量导数计算的直接扰动迭代法。最后，为了供读者参数，本文还导出了三种混合移频动柔度法的非迭代式，其中有两种恰好是另外两种动柔度法经混合移频后的非迭代式，这实际上已将另两种动柔度法也扩展到密集根情况了。     

1994年2月21日行星际激波引起的磁暴

利用Imp-8,Geotail和Goes-6等卫星资料,研究了1994年2月21日0900UT到达地球磁层的行星际激波引起的磁暴期间,从太阳风向磁层传输能量的有关问题.结果指出:（1）南向行星际磁场（IMF）的长持续时间不是太阳风向磁层输能的必要条件.南北振荡的,较强IMF也能产生显著的能量传输;（2）行星际扰动磁场通过弓激波和磁层顶后扰动磁能增加,增幅将近5倍;（3）在磁层内扰动磁场的Bz分量在1×10-4Hz附近显著被吸收.这一低频扰动磁场可能是磁暴期间导致氧离子和质子等环电流粒子向内扩散并被加速的原因之一.     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

DME脉冲调制信号波形参数对空间频谱占用的影响分析

航空测距器DME的开发、调试和性能验证都要用到高斯双脉冲调制格式的DME信号。由于专用的DME信号模拟器技术复杂、价格昂贵,人们常用具有快沿双脉冲调制功能的模拟信号源替代。本文以航空测距器DME信号要求为依据,初步分析了这种替代可能存在的问题,并通过实验对不同边沿条件下高斯双脉冲、矩形双脉冲调制信号的功率频谱占用情况进行了验证。     

Ultrasound assisted solidification process of ternary Cu–Sn–Sb alloy

It is well-known that the application of ultrasound during liquid to solid transitions for alloys can refine the solidification microstructure and thus improves the mechanical properties. How-ever, most published work focuses on single phase dendritic growth, whereas little has been con-ducted on the multiphase alloys with complicated phase transformations during solidification. In this work, the solidification process of ternary Cu40Sn45Sb15 alloy was realized within intensive ultra-sonic field with a resonant frequency of 20 kHz and ultrasound power from 0 W to 1000 W. The ultrasound refines the size of the primary e(Cu3Sn) intermetallic compound by two orders of mag-nitudes. If the ultrasound power increases to 1000 W, g(Cu6Sn5) phase nucleates and grows directly from parent liquid phase without the occurrence of peri-eutectic reaction on the top of the alloy sam-ple where the ultrasound intensity is sufficiently high. These microstructural variations lead to the enhancement of compressive strength and elasticity modulus of ternary Cu40Sn45Sb15 alloy.     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).