A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

基于非接触式测量的旋转叶片动应变重构方法

基于叶端定时非接触式测量和振动响应传递比的概念,开展高速旋转叶片动应变重构方法的研究。在频域内推导了叶片任意测点位移与任意测点动应变的传递比,给出了单模态共振下响应传递比关于位移和应变模态振型的解析表达式;建立旋转叶片的三维(3D)有限元模型,开展考虑旋转预应力效应的叶片模态分析,提取位移和应变模态振型,获得任意转速下叶端位移与叶根关键点动应变的传递比。开展高速旋转叶片叶端定时非接触式测量实验,采用周向傅里叶算法对叶端定时信号进行处理,获得叶片在不同转速单模态共振下的叶端位移,结合响应传递比,重构5个旋转叶片的关键点动应变。结果表明:旋转叶片在9000r/min和13000r/min转速下发生1阶共振时,与应变片实测结果相比,叶根处应力最大点、次大点和边缘点3个关键点的动应变平均重构误差均小于15%,验证了旋转叶片动应变重构方法的有效性。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

惯性仪表标定误差的补偿抑制技术综述

本文综述了惯导测试设备误差源、运动参数激励误差、误差传递方法,介绍了如何获取在惯性仪表坐标系下的精准运动参数激励,介绍了惯性仪表测试误差自动补偿、抑制方法。最后综述了惯性仪表测试误差的评估方法,阐述了惯性仪表测试标定技术的发展方向。     

基于DSP的感应同步器测角系统的设计与实现

本文介绍了一种基于DSP的感应同步器测角系统的设计与工程实现,其核心是角位置的数据变换及编码部分.该设计提高了测角系统的性能,特别是大幅度地提高了位置测量的分辨率和精度.     

发动机试验液氢流量测量不确定度评定

针对某型号液体火箭发动机试验,介绍了液氢低温流量测量系统组成及原理。根据液氢质量流量测量数学模型,分析影响液氢流量测量不确定度的主要压力对贮箱容积的影响因素,依据不确定度评定相关标准和方法,对各种影响因素进行分析,最终得出液氢质量流量扩展不确定度为±0.88%,满足发动机设计部门对液氢低温质量流量测量不确定度±1%的要求。     

数字示波器在尖峰干扰脉冲强度测量中的应用

运用数字示波器瞬态捕获能力及面积测量功能，快速、准确、不遗漏地测量电子设备的尖峰干扰信号（脉冲信号），用公式将脉冲强度单位换算为脉冲频谱密度单位。     

电镀砂轮磨损对GH4169磨削表面完整性的影响

电镀砂轮具有优异的成型性和形状保持能力,越来越广泛地应用于复杂曲面的加工,但是磨损对零件表面完整性影响的研究并不充分.在深入分析利用圆环型砂轮在插磨方式下加工GH4169试件所产生的表面形貌形成规律的基础上,对高刚度矩形试件的磨削表面粗糙度随砂轮磨削量的变化进行了详细记录,并对某型号发动机静子叶片进行实际磨削验证.试验结果表明,精磨时适当的砂轮磨损可以使高刚度试件表面粗糙度下降35％,对表面硬度和残余应力影响不大;而叶片的弱刚度会大幅提高磨削粗糙度,但适当的砂轮磨损可以使叶片端部粗糙度下降64％,并降低刚度对粗糙度的影响,进而提高叶片表面磨削质量的一致性.因此,通过磨削粗糙度对砂轮的磨损状况进行大致评估,选择合适磨损量的砂轮用于精加工,以充分降低工件的表面粗糙度并提高磨削质量的一致性.     

基于单片机的多点温度采集系统设计

随着单片机技术的迅速兴起与蓬勃发展,其稳定、安全、高效、经济等优点十分突出。为了实现多点温度数据的精确采集,采用了一种基于单片机AT89C52为核心的数据采集系统,该系统具有电路简单、功耗低、抗干扰能力强、可靠性高等优点,能够通过DBW热电阻变送器对热电阻随温度的变化而得到的模拟信号进行采集,并通过A/D转换器对模拟信号进行模数转换;同时实现基本的人机对话功能,包括使用按键设定温度报警阀值,通过LED数码直读显示检测点、温度等功能。其温度测量精度可达到1℃。