喷口辐射热泄漏对延伸段壁温分布的影响

引入喷口的热辐射泄漏损失，导出辐射冷却推力室壁温的计算方程。分析表明，考虑与不考虑喷口热损失二者相比较，前者壁温约下降７０℃。本结果可为喷管延伸段材料的选取提供更为科学的理论依据。     

2.5D石英纤维织物增强二氧化硅基复合材料弯曲性能测试研究

简要介绍了2．5D石英纤维织物增强二氧化硅基复合材料弯曲性能测试装置，通过对比试验研究了试样跨厚比、变形测量等对材料弯曲性能的影响，用数理统计的方法对总体均值进行了显著性检验，合理确定了材料弯曲性能测试的试验参数。     

联合应用现代优化方法与S2流面计算进行多级涡轮的气动设计

本文联合应用S2流面正问题计算和多级局部优化设计对某三级涡轮进行多级气动优化设计。优化联合采用人工神经网络和遗传算法,流场计算采用全三维粘性流N-S方程求解,计算网格采用H-O-H型网格,即入口段、出口段采用H型网格,叶片区域采用O型网格。通过优化,总效率提高1.1%,总体性能提高,达到设计要求。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

建立空分中N2O的检测方法,确保设备安全运行

介绍了建立N2O检测方法原由,操作变量的选优及对空分安全生产的建议.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

模糊信息环境下的综合评判

 本文针对各种模糊信息环境下的综合评判问题,即多准则决策中的离散型决策问题,提出了3种模糊综合评判模型及模型在各种不同的决策需要下的具体的实现方法。试图解决在模糊权值或模糊判定或权值及判定均为模糊的环境下,以及不同的决策需要时的实际的综合评判问题。     

TC6钛合金棒材热处理工艺研究

对TC6钛合金φ20mm～φ120mm不同规格棒材进行了普通退火、双重退火、等温退火、固溶时效等热处理方法和热处理制度研究,并对比分析了热处理制度和组织、性能之间的影响关系,结果表明,TC6钛合金的组织和性能对热处理工艺敏感,应根据半成品规格、类型、截面形状、使用温度、受力情况以及设备条件等诸多因素选择合适的热处理方法和制度,才能达到强度、塑性和韧性的最佳匹配。研究结果证实普通退火是一种简单易行的退火制度,适用于飞机结构用中等规格棒材等半成品的退火,进一步提出了TC6钛合金棒材的热处理工艺选择原则。     

2D70铝合金热稳定性研究

2D70是可热处理强化的耐热铝合金,一般用在高温场合.以2D70铝合金自由锻件为对象,研究了热稳定化处理对合金室温、高温拉伸性能的影响,测定了合金的高温持久、蠕变性能,并观察了合金在这些高温试验条件下的组织变化.结果表明,2D70铝合金的耐热性较好,可在150℃长时使用,175℃以下时,合金的性能和组织变化都不明显;高温下合金的断口呈现沿晶断裂特征.