结构比强度及其在优化设计中的应用

本文从结构重量角度推导了比强度(含比模量)表达式,分析了对同一材料不同比强度的关系,给出了比强度在结构动态分析中及结构优化设计中的应用。     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

水热-凝胶法ZrO2 气凝胶的制备与表征

以硝酸氧锆为锆源,尿素为凝胶促进剂,通过水热凝胶法结合超临界乙醇干燥,可成功制备出具
有良好纳米三维网络结构的ZrO2 气凝胶。采用透射电镜(TEM)、比表面积及孔隙度分析仪(BET),X 射线衍
射仪等测试手段对其结构进行了表征与测试。结果表明,ZrO2 气凝胶主要由无定型和四方晶相组成,其比表
面积为445 m2 / g,孔径主要分布在5 ~7 nm 和30 ~40 nm 两处。     

多加速度计振动分离惯性补偿测力技术

为解决在高超声速脉冲风洞中进行大长细比等特殊模型测力实验所面临的惯性补偿问题,笔者提出了多加速度计振动分离惯性补偿方法。这一方法应用在长细比达20 :1 的模型气动力实验中,得到了较为理想的实验结果     

系统辨识的计算机辅助设计实现

探讨了通过脉冲响应法来求取被识别系统的传递函数的过程,给出了计算公式,最后利用MATLAB对计算过程进行了可视化的编程实现。     

蓄热式太阳能热光伏-热推进双模系统换热特性数值模拟研究

本文通过三维数值模拟研究蓄热式太阳能热光伏-热推进双模系统的蓄/释热特性和推进性能。在蓄热式太阳能热推进系统工程模型的基础上,通过射线光学的光路分析验证了聚光器设计的合理性,并获得吸热腔壁面能量分布情况,进一步研究了相变蓄热过程的影响因素。基于场协同原理对热光伏再生冷却结构进行了优化设计,使热光伏具有较好的散热特性,提高发电功率;通过整机流动换热仿真,分析了工质流体在推进器内部的换热情况,计算结果表明,蓄热式热推进器具有达到734s比冲和0.9N推力的推进性能,以及能够满足日蚀区微小卫星的供电和推力需求。     

电机绝缘系统在高频冲击下局部放电试验研究

高频冲击局部放电(PD)测试可以有效的检测电机绝缘系统的绝缘状态。根据传感器的不同,电机绝缘系统在高频冲击下PD测试方法主要有两种:高频电流传感器法和超高频天线法。试验表明:在高频冲击电压下,PD主要发生在冲击的上升沿和下降沿,在同一放电电压下,上升沿和下降沿的PD幅值较大;在风力发电机定子绝缘系统鉴别试验中,随着老化试验的进行,线圈的PD起始电压总体呈下降趋势。通过鉴别试验,可以确定绝缘系统的冲击电压绝缘等级及类型。     

周期矩形脉冲信号强度校准方法的研究

脉冲信号强度是信号脉冲响应、电磁波测量中的关键指标。基于脉冲信号接收机和数字示波器工作原理,通过周期脉冲信号傅里叶变换这一理论基础,建立周期矩形脉冲信号强度校准数学模型。采用数字示波器测量周期矩形脉冲幅度、脉冲宽度等,对校准测试数据进行分析,证明用数字示波器建立周期矩形脉冲信号强度校准系统的科学性和有效性。     

小功率氮电弧推力器的性能

采用自然辐射冷却结构的小功率电弧推力器,实现了以氮气为推进剂的长时间稳定运行。采用间接测力方法得到推力,利用铜镜反射法拍摄喉道处的放电状态,结合测量的弧电压、弧电流和气流量数据以及导出的比冲和推力效率,对推力器运行性能和放电特性进行了研究。结果显示:在气流量为100~700mL/min,输入功率为35~55W的条件下,最大推力约为24mN,最大比冲接近175s,当弧电流为80~120mA范围内变化时,弧电压变化范围为420~520V,并且弧电压随气流量的增加呈现出先下降后上升的趋势。