全文获取类型
收费全文 | 148篇 |
免费 | 113篇 |
国内免费 | 18篇 |
专业分类
航空 | 176篇 |
航天技术 | 49篇 |
综合类 | 3篇 |
航天 | 51篇 |
出版年
2023年 | 4篇 |
2022年 | 12篇 |
2021年 | 19篇 |
2020年 | 3篇 |
2019年 | 4篇 |
2018年 | 8篇 |
2017年 | 6篇 |
2016年 | 6篇 |
2015年 | 6篇 |
2014年 | 10篇 |
2013年 | 17篇 |
2012年 | 22篇 |
2011年 | 14篇 |
2010年 | 16篇 |
2009年 | 12篇 |
2008年 | 10篇 |
2007年 | 15篇 |
2006年 | 19篇 |
2005年 | 11篇 |
2004年 | 9篇 |
2003年 | 9篇 |
2002年 | 2篇 |
2001年 | 7篇 |
2000年 | 3篇 |
1999年 | 6篇 |
1998年 | 9篇 |
1997年 | 3篇 |
1996年 | 1篇 |
1995年 | 3篇 |
1994年 | 2篇 |
1993年 | 2篇 |
1992年 | 2篇 |
1991年 | 3篇 |
1990年 | 1篇 |
1989年 | 2篇 |
1988年 | 1篇 |
排序方式: 共有279条查询结果,搜索用时 15 毫秒
91.
空间飞行器导航定位的精度及可靠性很大程度上取决于雷达误差修正模型准确与否。以脉冲雷达为研究对象,采用统计假设检验理论,对雷达测量数据有无野值等不同情形,分别建立了误差模型拟合优度F 检验与容错F-检验、模型分量显著性T-检验和容错T-检验算法,并且利用雷达跟踪飞行器的实测数据对算法进行了验证。结果显示,模型拟合优度检验与模型分量显著性检验等系列算法具有良好的容错性和适应性,可用于诊断雷达误差模型是否正确有效。 相似文献
92.
根据脉冲爆震发动机工作循环过程中的压力变化特点,对脉冲爆震发动机自吸气的实现方式进行了探索研究,设计了几种不同的结构型式以改善尾部吸气质量,并进行了数值模拟。结果显示:单一等截面直爆震管虽然可以在爆震后管内负压作用下从尾部自吸气,但是吸入的基本全是尾气,无法用于再次爆震起爆;进、排气口分开有利于改善自吸气质量,进气口离排气口越远,尾气影响越小,吸气质量越好;进、排气口间最好有一定压差,否则会出现两端同时进气,形成吸气震荡,并在爆震管中部夹有燃气无法排出;利用设计的气动阀可以实现从爆震管前端自吸气,吸气结束后整个爆震管内充满新鲜空气,可以用于再次爆震起爆。 相似文献
93.
根据脉冲爆震发动机(PDE)工作特点为其设计了6组不同结构的圆柱型引射器,并针对各种结构引射器,采用力传感器法对不同轴向位置处引射器的增推性能进行了实验研究,实验采用汽油为燃料,空气为氧化剂。实验结果发现,轴向位置对引射器的增推性能有非常明显的影响,当引射器入口正好位于脉冲爆震发动机出口处(0点)或位于下游1/2倍脉冲爆震发动机直径处时,系统会出现一个至少高于35%的推力增益点,但是当引射器入口从该点继续远离发动机出口位置时,推力将会急剧地下降;当引射器从0点逐渐向上游移动时,引射器的推力增益呈先下降后上升再下降的趋势,最高推力增益可达80.5%。 相似文献
94.
95.
96.
为研究旋转爆震发动机(Rotating Detonation Engine, RDE)中燃料/氧化剂喷射和掺混对爆震波的影响及非预混环境下的爆震波的快速起爆与稳定传播,本文采用线性模型爆震发动机(Linear Model Detonation Engine,LMDE)来简化实际燃料喷射与爆震波相互作用的物理问题。通过RNG K-?湍流模型结合7步7组分氢气/空气机理的三维非定常反应流模拟方法,探究真实喷射条件下爆震波与混气相互作用、爆震波衰减及自持的特性。结果表明:氢气/空气的掺混均匀度至少要达到0.6才能使爆震波在非预混环境下传播;氢气孔与空气缝的入口压比需要满足爆震波进入燃烧室时,非均匀混气区恰好集中在氢气孔附近,燃料完全释放能量维持爆震波传播。 相似文献
97.
98.
为了获得回流型脉冲爆震燃烧室在不同工作频率下的工作特性,通过试验和数值相结合的方法对该爆震室工作频率10~30Hz时的出口燃气总压、总温、流量变化规律以及该爆震室的增压能力进行了测试与计算分析。结果表明:出口燃气总压、总温具有极高的峰值和较高的平台区,其工作频率10~30Hz时,压力平台值为0.36~0.91MPa,时均温度为710~1270K。此外,该爆震室排气流量十分集中,以10Hz为例,在一个爆震循环的16%时间内,排出了整个循环60.5%的燃气。为此对出口燃气总压进行质量加权平均,发现该爆震室的增压比随工作频率的增加而降低,在2.05~2.37。 相似文献
99.
Plasma Synthetic Jet (PSJ) actuators have shown wide and promising application prospects in high-speed flow control, due to their advantages including high exhaust speed, wide frequency band, rapid response, and non-moving components. Although previous studies on PSJ actuators are abundant, most of them have focused on the performance of a single actuator. However, in practice, an actuator array is very necessary for large-scale aerodynamic actuation on account of the small affected area of a single PSJ. In this paper, the characteristics of a two-electrode plasma synthetic jet actuator array in serial are investigated experimentally. Compared to a parallel actuator array, the serial actuator array requires simpler power supply design and is much easier to realize. High-speed photography of the discharge evolution, voltage-current measurement, and shadowgraphy visualization are used in the investigation. Experimental results show that, for the serial actuator array, weak discharges happen firstly between energized and suspending electrodes, and then a strong pulse arc discharge is triggered. The breakdown voltage in serial is irrelevant to such factors as the number of actuators, the maximum or minimum gap in serial, the connection sequence, etc. It is mainly determined by the sum of gaps. For serial actuators with the same anode-to-cathode spacing, the energy deposition is the same, and the jet is synchronous and similar. Because of the entrainment and merging of adjacent jet vortices, the jet front speed of an aligned synchronous jet array increases as the orifice distance decreases. To achieve the highest jet front velocity, the orifice of the actuator has an optimal diameter. 相似文献
100.
针对目前合成孔径雷达回波模拟器图像校准方法存在的诸多不足,介绍了一种测量图像参数的方法。根据此方法建立的合成孔径雷达回波模拟器图像校准装置,可以通过对数据的正交解调、脉冲压缩、成像算法以及滤波等处理方法,实现合成孔径雷达回波的成像及校准。 相似文献