Ka波段高中频四次谐波混频器的实现

推导了反对接二级管混频原理与相差合成原理相结合实现四次谐波混频公式。结合公式提出了在Ka波段实现高中频四次谐波混频器的新的设计方案 ,进行了电路仿真并制作了混频器电路 ,通过仿真所得到的实验结果表明 ,公式推导正确设计思路切实可行     

飞机高升力系统扭力管旋转角度测试方法

在飞机地面模拟试验环境下需要测试高升力系统襟翼扭力管旋转角度.由于扭力管属于系统试验件,在不改变试验环境构型的情况下不可截断或更换安装用于测试扭力管旋转角度的旋转编码器.本文利用同步轮法实现了在不破坏扭力管前提下安装旋转编码器测试扭力管旋转角度,方法简单、可靠,且容易实现,很好的满足了试验大纲要求.     

不同校准装置对引压管腔动态特性校准

为了探索引压管腔在动态压力校准中各校准方法的一致性与数据准确性,确立了以简单直管形式引压管腔开展动态特性校准的研究。采用理论和仿真的手段分析并建立了引压管腔模型,理论模型和仿真结果一致性极高。利用3种正弦压力校准装置对同一引压管腔进行了动态校准组合试验,结果表明:3种校准方法所得的动态特性与理论分析趋势一致,对于引压管腔基频的校准各试验之间偏差小于0.55%,但与基频理论值最大偏差为-3.17%。该研究将会为未来引压管腔结构设计和动态特性的补偿修正提供了一定参考依据。      

翻管数值参数分析法研究

采用塑性流动理论，薄壳无力矩理论及幂函数强化模型，对求解轴对称塑性平面应力问题的数值参数法作了进一步的研究，推导出成形力学分析的一阶微分方程组，在此基础上，将该微分方程相应用于薄壁圆管轴压外翻成形的稳态流动分析，计算时采用了四阶龙格库塔法，并获得了应力，应数值解，本文通过大量的计算，分析了边界条件对计算结果的影响，并将理论计算结果与实验作了比较。研究结果表明，轴对称塑性平面应力问题可以转换为一阶常     

激波管壁面边界层脉动特性的分析与计算

本文分析了激波管壁面湍流边界层脉动压力的强度、脉动压力的频率特性及共传播与衰减特性,给出了这些特性的计算方法。通过算例说明了②区和③区壁面脉动压力的强度及其频率随激波马赫数的变化规律,并讨论了壁面脉动对激波管气流品质的影响。     

大口径激波管中降低雷诺数的方法

提供了一种在大口径激波管中降低2区气流雷诺数的方法。采用该方法雷诺数可由通常的10~6～10~7量级降至工10~5量级。实验结果表明采用此方法后2区流场未受明显扰动。给出了驱动压比 P_41与主激波马赫数 M_S1间关系式并由实验加以验证。     

氢氧爆轰波与界面的相互作用

用ＴＶＤ格式数模拟了初压在０．１～１．０ＭＰａ，３Ｈ２＋Ｏ２的爆轰波与固壁的反射特性，以及初压在１．０ＭＰａ，３Ｈ２＋Ｏ２的爆轰波与初压在０．００２～０．３ＭＰａ范围内的卸煤气体（Ｎ２）的相互作用特性。并在φ１００ｍｍ的爆轰试验管上进行实验验证。结果表明：串接卸爆段后的反射峰压比不串接卸爆段时降低了８３％左右；定常驱动时间比反射激波时可延长４０％。驱动段产生的定常驱动时间可达到１ｍｓ／ｍ。     

电涡流激振圆管的试验研究

ＪＤＺ－３型电涡流激振是研究外覆纤维合材料薄壁金属圆管振动特性的激振源，本文阐述了电涡流激振的工作原理，性能特征及其在研制过程中所进行的各种试验，如涡流感应头结构型，恒磁路系统，激振器与试件之间的间隙，交流激磁强度和感应头激磁线圈的设计等。还介绍了激振器与功效的阻抗匹配，最后，用该设备对六种不同圆管进行激振试验，取得了良好的结果。     

Influence of deformation zone length on bending radius of SS304 tubes with small diameters manufactured via free bending-based active motion

In three and six-axis free-bending equipment, the deformation zone length(A) is a fixed mechanical structure parameter modified when the relevant structure is redesigned and manufactured. In this study, a six degree of freedom(6-DOF) parallel mechanism was used as the control mechanism of the bending die, and a new method of changing the deformation zone length(A)was proposed. Firstly, an idealized geometric model of free bending-based active motion was established. Then, the influence of the de...     

Plastic wrinkling model and characteristics of shear enforced Ti-alloy thin-walled tubes under combination die constraints and differential temperature fields

Plastic wrinkling predictions and shear enforced wrinkling characteristics of Ti-alloy thin-walled tubes under combination die constraints have become key problems urgently in need of solutions in order to improve forming quality in their shear bending processes under differential temperature fields. To address this, a wrinkling wave function was developed by considering their shear bend deformation characteristics. Based on this wave function and the thin shell theory, an energy prediction model for this type of wrinkling was established. This model enables considera-tion of the effects of shear deformation zone ranges, material parameters, loading modes, and fric-tion coefficients between tube and dies on the minimum wrinkling energy. Tube wrinkling sensitive zones (WSZs) can be revealed by combining this wrinkling prediction model with a thermal-mechanical coupled finite element model for simulating these bending processes. The reliability of this wrinkling prediction model was verified, and an investigation into the tube wrinkling char-acteristics was carried out based on the experimental conditions. This found that the WSZs are located on either a single side or both sides of the maximum shear stress zone. When the friction coefficients between the tube and the various dies coincide, the WSZs are located on both sides. The larger the value of the tube inner corner radius and/or the smaller the value of the outer corner radius, the smaller the wrinkling probability. With an increase in the value of the moving die dis-placement, the wrinkling probability increases at first, and then decreases.