金属网反射器索网预应力对模态的影响

卫星姿态和轨道调整时,金属网反射器索网结构的基频过低会使反射器产生振颤。文章通过金属网反射器索网结构的模态方程,利用有限元法来分析预张力的值与模态之间的关系,得到了预张力的大小对索网模态的影响规律,索网的基频会随着预张力的减小而下降,并用算例验证了这种方法的正确性。     

基于加工误差仿真的半球谐振子优化设计

针对半球谐振陀螺谐振子制造过程中存在的加工误差,采用有限元仿真,分析了半球谐振子结构参数、尺寸公差和形位公差变化对其工作模态频率和临近模态频率的影响,研究了半球谐振子形位公差变化对频率裂解和品质因数的影响。通过仿真分析可知,半球谐振子结构参数壁厚、半球中心半径及内倒角半径都会影响模态频率;半球谐振子形位公差中的内外球心距离误差对其工作模态影响较大,中心轴平行误差对频率裂解和品质因数影响较大;半球谐振子壁厚、内倒角半径、小柱半径及内外球心距离误差变化会使工作模态频率与相邻模态间存在干扰。在此基础上,提出了半球谐振子结构参数及形位公差优化设计建议,并通过半球谐振子品质因数Q值和频率裂解测量对该建议进行了验证。     

RLV双环滑模RCS/气动舵复合控制器设计

针对可重复使用运载器(RLV)再入飞行强非线性、快时变特性和多种控制模式给姿态控制器设计带来的困难和挑战,提出了一种双环滑模反作用控制系统(RCS)/气动舵复合控制器设计方案。首先建立了RLV再入飞行的数学模型,基于时标分离原理,设计了快、慢双环回路控制系统,并采用滑模控制律(SMCL)获得控制力矩指令;所设计的RCS/气动舵复合控制器,由控制分配将控制力矩指令分别映射成RCS推力器执行的开关指令和气动舵面偏转指令,采用链式递增融合协调气动舵与RCS的复合控制。仿真结果表明,双环滑模RCS/气动舵复合控制器能较好地完成姿态跟踪控制,有效地节省RCS燃料,实现了气动舵面与RCS的协调控制。控制方案也能用于再入飞行器或空天飞机的控制系统设计。     

Improving Mode II delamination resistance of curved CFRP laminates by a Pre-Hole Z-pinning (PHZ) process

This paper presents an experimental investigation of the Mode II delamination resistance of curved CFRP laminates reinforced with Z-pins. A Pre-Hole Z-pinning (PHZ) process is developed to reduce the in-plane damage of the Z-pinned laminates. The microstructural observation of the Z-pinned laminate specimens indicates that the PHZ process can effectively decrease the defects including the Z-pin offset angle and the area of eyelet zone. The influences of the volume fraction and diameter of Z-pin on the fracture toughness and the delamination crack growth rate of the specimens under End Notch Flexure (ENF) loading are then determined experimentally. The test results show that Z-pin increases the interlayer stiffness of the laminate. The delamination crack growth rate is reduced with the increase of Z-pin diameter and volume fraction, and a reduction up to 40% is achieved compared with the specimens without pins. Furthermore, the Mode II fracture toughness is significantly improved with the increase of Z-pin volume fraction. When Z-pin volume fraction increases by 1%, the achieved fracture toughness is about 200% higher compared to the unpinned laminates.     

圆柱贮箱中液体晃动的模部分析

本文对圆柱贮箱中液体的晃动问题进行了精细研究，提出了模部及模部分析的新概念。在此基础上，文章研究了在不同接触角假设下的模部正交性问题，对传统的圆柱贮箱中液体的受迫晃动理论作了本质分析，并从速度势函数ｚ模部的角度分析了深箱问题的实质。     

可变构型复合柔性结构航天器动力学建模研究

针对中心刚体加复合柔性结构类航天器采用混合坐标法和子结构模态综合法，建立了可变构型复合柔性结构航天器低阶动力学模型。获得的柔性动力学方程及其各类耦合系数矩阵，适用于全星级可变构型系统和部件级复合柔性附件系统的控制系统设计与仿真，该模型具有阶数低和工程实用的特点。     

Numerical analysis for impacts of nozzle end-clearances on aerodynamic performance and forced response in a VNT turbine

It has been well known that nozzle end-clearances in a Variable Nozzle Turbine (VNT) are unfavorable for aerodynamic performance, especially at small openings, and efforts to further decrease size of the clearances are very hard due to thermal expansion. In this paper, both the different sizes of nozzle end-clearances and the various ratios of their distribution at the hub and shroud sides were modelled and investigated by performing 3D Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA) simulations with a code of transferring the aerodynamic pressure from the CFD results to the FEA calculations. It was found that increasing the size of the nozzle end-clearances divided equally at the hub and shroud sides deteriorates turbine efficiency and turbine wheel reliability, yet increases turbine flow capacity. And, when the total nozzle end-clearances remain the same, varying nozzle end-clearances’ distribution at the hub and shroud sides not only shifts operation point of a VNT turbine, but also affects the turbine wheel vibration stress. Compared with nozzle hub clearance, the shroud clearance is more sensitive to both aerodynamic performance and reliability of a VNT turbine. Consequently, a possibility is put forward to improve VNT turbine efficiency meanwhile decrease vibration stress by optimizing nozzle end-clearances’ distribution.     

A simulation study on the mode conversion process from slow Z-mode to LO mode by the tunneling effect and variations of beaming angle

For a particular angle of incidence wave, it is possible for a slow Z-mode wave incident on an inhomogeneous plasma slab to be converted into an LO mode wave. But for another wave normal angle of the incident wave, it has been considered impossible, since an evanescence region exists between two mode branches. In this case we expect that the mode conversion takes place through the tunneling effect. We investigate the effect of the spatial scale of the density gradient on the mode conversion efficiency in an inhomogeneous plasma where the mode conversion can occur only by the tunneling effect. We use the computer simulation solving Maxwell’s equations and the motion of a cold electron fluid. By considering the steepness of the density gradient, the simulation results show the efficient mode conversion could be expected even in the case that the mismatch of the refractive indexes prevents the close coupling of plasma waves. Also, we show for these cases the beaming angle does not correspond to Jones’ formula. This effect leads to the angles larger and smaller than the angle estimated by the formula. This type of mode conversion process becomes important in a case where the different plasmas form a discontinuity at their contact boundary.     

基于三维有限元的火箭模态振型斜率预示方法研究

振型斜率火箭是姿控系统设计的重要参数,对飞行任务的可靠性与安全性有着至关重要的作用。依据全箭动特性的测量原理及参数定义,结合三维有限元建模方法和模型修正技术,全面考虑了速率陀螺、惯组安装位置处的局部刚度对振型和振型斜率的影响,建立了基于局部细节精细化建模的全箭模态振型斜率预示方法,并总结了3种不同的振型斜率提取方法,提高了振型斜率的预示精度。同时提供了三维模型振型一维化的方法,解决了使用三维有限元模型计算弹性运动方程式系数的难题。     

Applying fuzzy bi-dimensional scenario-based model to the assessment of Mars mission architecture scenarios

Sending man to Mars has been a long-held dream of humankind. NASA plans human planetary explorations using approaches that are technically feasible, have reasonable risks and have relatively low costs. This study presents a novel Multi-Attribute Decision Making (MADM) model for evaluating a range of potential mission scenarios for the human exploration of Mars. The three alternatives identified by the Mission Operations Directorate (MOD) at the Johnson Space Center (JSC) include split mission, combo lander and dual scenarios. The proposed framework subsumes the following key methods: first, the conjunction method is used to minimize the number of alternative mission scenarios; second, the Fuzzy Risk Failure Mode and Effects Analysis (RFMEA) is used to analyze the potential failure of the alternative scenarios; third, the fuzzy group Real Option Analysis (ROA) is used to estimate the expected costs and benefits of the alternative scenarios; and fourth, the fuzzy group permutation approach is used to select the optimal mission scenario. We present the results of a case study at NASA’s Johnson Space center to demonstrate: (1) the complexity of mission scenario selection involving subjective and objective judgments provided by multiple space exploration experts; and (2) a systematic and structured method for aggregating quantitative and qualitative data concerning a large number of competing and conflicting mission events.