基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

MDS图在液态模锻工艺过程单片机仿真控制系统中的应用

本文介绍了液态模锻工艺过程单片机仿真控制系统的设计方法，包括液态模锻工艺程确立、逻辑量确立、硬件系统设计、ＭＤＳ图的建立及软件实现，在工艺设备的逻辑性控制中应用ＭＤＳ图控制结构设计的控制器可方便方便地实现ＰＬＣ的控制功能，也可主便地实现其他娄字逻辑系统的控制功能。     

气体注入压力激励法测量卫星液体推进剂剩余量的热力学模型

通过对气体注入压力激励法测量卫星液体推进剂剩余量系统的详细热力学过程分析,建立了能满足实际测量需求的等温和绝热两种热力学模型,对具体测量模型的选用及相关问题进行了分析。     

Implication of multiple dipolarization event near 9 RE for the physics of substorms

In 2001, 2002 and 2003, the Polar spacecraft probed the near equatorial plasma sheet at 9 R_E near local midnight. Using the magnetic field observations, the signatures at substorm onsets are studied. Close to the flux pile-up region, the Polar spacecraft readily detects the dipolarization front, especially for pseudo onsets. An event with two distinct onsets has been examined. The signatures are found to be consistent with the multiple-onset model suggested by Russell [Russell, C.T. How northward turnings of the IMF can lead to substorm expansion onsets. Geophys. Res. Lett. 27, 3257–3259, 2000] which is a modified Near-Earth Neutral Line (NENL) model. Another similar event is also examined showing the effects of different Interplanetary Magnetic Field (IMF) conditions upon substorms. Moreover, ground effects can be very weak compared to in situ observations, especially for pseudo onsets, because these signatures appear to be localized and not global.     

Mathematical description of the NaK model for MASTER-2005

The release of NaK droplets has been modeled for the new version of the European Meteoroid and Space Debris Terrestrial Environment Reference model MASTER-2005. Previously published versions of the model have been revised. The parameters of the model are introduced and discussed. NaK droplets consist of eutectic sodium–potassium alloy and have been released during RORSAT reactor core ejections. They contributed to the space debris environment in the centimeter and millimeter size regime. Sixteen nuclear powered RORSATs launched between 1980 and 1988 activated a reactor core ejection system in Sufficiently High Orbits (SHO), mostly between 900 and 950 km altitude. The core ejection caused an opening of the primary coolant circuit. The liquid coolant has been released into space during these core ejections. The outflow is considered as a discrete event for each of the sixteen core ejections in total. The NaK coolant has been forming droplets up to a diameter of 5.5 cm. NaK releases are restricted to a very narrow region near 65° inclination. This paper gives the parameters of the NaK release model as it is implemented in MASTER-2005. The quantitative values of all model parameters including characteristic diameter and uniformity parameter are presented. The ratio of the characteristic droplet size to the orifice diameter is discussed. It is estimated that altogether 128 kg of NaK-78 (8 kg per RORSAT) was released on orbit. Simulation runs show that there are still 45,000 droplets with a total mass of 97 kg in orbit at the reference epoch 1 May 2005, whereas the smallest droplet has a diameter of 5 mm. Results of orbit propagation simulation runs are presented in terms of spatial density.     

可展开式辐射器热控对航天器轨道调整的适应性分析

为提高航天器热控系统对轨道调整的适应能力，本文研究了与流体回路耦合的可展开式辐射器热控方案在不同轨道高度下的热控性能，分析了不同轨道高度时辐射器面临的热环境的影响，在不同轨道高度下比较了固定辐射器与可展开辐射器的热控特性。结果表明，随着辐射器展开角度的变化，辐射器吸收的空间热流随之发生变化，从而对热控系统的散热能力带来直接影响，调节辐射器的角度可以扩大其对外散热能力。在工程应用中，基于热控流体回路，通过调节可展开式辐射器的展开角度，可以有效提高航天器的轨道热适应能力。     

Understanding magnetotail current sheet meso-scale structures using MHD simulations

Recent Cluster observations have strongly supported the existence of meso-scale structure in the magnetotail current sheet. In our study, a magnetohydrodynamic simulation event study exhibited current sheet behavior comparable to that seen in the Cluster observations. Geotail and DoubleStar observations also show that the simulation is providing a realistic representation of the magnetosphere during the period of interest; that is, when the current sheet evidently becomes bifurcated. The magnetohydrodynamic simulation allows us to place the local observations into a global contest. It shows that the observations can be explained in terms of localized reconnection tailward of the Cluster location and the formation of a flux rope nearby. The simulation also features wave-like structure across the current sheet.     

针栓式喷注单元膜束撞击雾化混合过程数值模拟

为了全面认识针栓式喷注器喷雾场结构，基于自适应网格加密技术和分三相计算的PLIC VOF（Piecewise Linear Interface Calculation Volume of Fluid）方法对针栓式喷注单元膜束撞击雾化混合过程进行了仿真分析，通过对两路推进剂分别进行界面追踪，获得了膜束撞击雾化混合过程的详细结构特征，与高速摄影试验结果定性定量对比均吻合较好，验证了数值方法的准确性。以此为基础对膜束撞击的喷雾场结构、撞击变形过程、流场涡结构、雾化破碎典型特征及破碎后的雾化混合分布特征进行了识别分析，结果表明：膜束撞击形成了液束未穿透液膜和液束穿透液膜2种不同的喷雾扇结构。膜束撞击形成的喷雾扇呈"Ω"形，膜束同时发生弯曲变形和横截面变形。另外，膜束撞击同时受到正压和剪切应力作用，导致了一系列复杂涡流现象，使得相互作用增强，雾化混合均增强，这也是膜束撞击喷注构型优于膜膜撞击的本质原因。最后，还发现膜束撞击喷雾场液滴分布呈现分区结构特征，分别是液束控制主导的上雾化区、液膜控制主导的下雾化区及夹在中间的混合区，实际中应兼顾雾化特性和混合特性，选取中等动量比膜束撞击，这可为针栓式喷注器的理论研究和工程设计提供重要参考。     

一种用于液晶曝光中的激光检测系统

介绍了一种非接触式激光检测系统，可用于检测液晶曝光中液晶模板与基板之间的间隙，给出了该种系统的测量原理、硬件系统、信号处理方法、测量结果、分辨力和误差分析，并指出了这种测量系统的应用。