彩色三维激光快速成型技术的研究

目前逆向工程采用线结构激光和一个彩色面阵CCD摄像机构成三维彩色扫描系统,彩色CCD摄像机分两次对被测物体成像,首先摄取物体的彩色图片,然后加用滤光片再摄取激光光平面上的三维信息.最后将两次获取的信息重叠,便可得到三维彩色信息.提出了激光光平面方程式三维测量方法,建立了相应的数学模型.研制成一套适用于彩色逆向工程流程,并进行了实验研究,给出了实验结果.     

无电阻CMOS带隙基准电压源的设计

设计了一种高准确度无电阻的带隙基准电压源。该电路采用差分结构的电压传输单元来代替电阻,并且没有使用运算放大器,从而避免了运算放大器所带来的高失调和必须补偿的缺陷。电流源采用共源共栅结构,提高了电源抑制比。增加了启动电路,保证电路可以正常工作。在0.6μm CMOS工艺条件下,电路的各项性能指标采用Sm artSp ice进行模拟验证,结果表明有效温度系数可以达到6×10-6/℃,电源电压从3.8 V变化到5.5 V时,输出的基准电压波动不到3 mV。     

标准压力源自校准方法探讨

当前以压力传感器为一次仪表组成的标准压力源,用软件实现自校准既可提高校准效率,又能提高仪器的性价比.对标准压力源的软件自校准方法进行了探讨.     

以激光束为基准测量工作台直线运动误差的原理探讨

提出一种以两束激光为基准测量工作台直线运动误差(五个自由度)的方法,并根据刚体运动学的基本原理导出了相应的数学模型。所获得的误差计算公式形式简单,计算方便,适用于实时、现场运动精度测量及补偿。     

飞机机身自动对接技术研究

介绍了飞机机身对接方式、采用的对接基准和对接测量方法,并以某飞机机身对接为实例,详细介绍了某型号机身自动化对接平台的建立流程、装配协调方法及激光跟踪仪和激光准直仪相结合的测量方法.     

电机变频控制实现换热器节能的应用研究

结合寒冷地区气候特点与通信机房温控的现状,针对50%浓度乙二醇溶液为工质的换热器,试验研究了自然冷源利用率与换热器自身变频节能的关系。结合乙二醇冷剂的特性,通过建立功率与频率关系模型、温差与功率和频率关系模型,实现了换热器循环泵和风机的变频控制策略。结果表明:在室内外温差、换热功率与循环泵、风机频率同时满足的条件下,以功率模型作为参数进行换热器自身的变频节能是可行的。通过对哈尔滨地区的气候数据与散热房控温试验分析,证明了乙二醇换热器的变频节能效果。     

飞秒激光能量密度对镍基合金重铸层和加工效率的影响

以航空发动机叶片制孔为导向,结合飞秒激光对单晶镍基高温合金材料的非热熔性损伤阈值(Φth1)和热熔性损伤阈值(Φth2)特征,研究了飞秒激光能量密度(0Φ44.2J/cm2)对制孔重铸层和加工效率的影响规律。研究结果表明:在Φth1ΦΦth2时,镍基合金经飞秒激光加工后加工侧壁没有出现明显的重铸物;在ΦΦth2时,加工侧壁开始出现重铸物,并随着能量密度的增加,重铸层厚度增大。在试验结果的基础上,建立了飞秒激光单脉冲加工深度与能量密度的定量关系。能量密度越高,飞秒激光单脉冲加工深度越大,加工效率越高。     

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

A shortcut to marking 3D target curves on curved surface via a galvanometric laser scanner

Marking arbitrary three-dimensional(3D) target curves on given objects with curved surface is required in many industrial fields, such as fabric prepreg placement in composite material part fabrication, product assembly, surface painting for decoration, etc. A shortcut to the solution of this intractable problem is proposed by utilizing a galvanometric laser scanner(GLS) with the aid of a camera. Without using the existing tedious GLS calibration procedures,the proposed method directly establishes a mapping between the 3D coordinates of the laser spots on the object surface and the control voltages of the scanner. A single-hidden layer feedforward neural network(SLFN) is employed to model the mapping. By projecting a dense grid of laser spots on the object to be marked and simultaneously taking only one image, the SLFN model is trained in minutes via a linear solving mechanism. Experiments demonstrate that the trained SLFN model has a good generalization performance for marking 3D target curves. The 3D laser marking errors on experimental objects are less than 0.5 mm. The proposed method is especially suitable for on-site use and can be conveniently extended to multiple GLSs for marking large complex objects.     

基于等效板的含离散源损伤机翼结构分析

研究离散源损伤对机翼结构的影响,可以大幅度提高飞机在不良损伤事故下的生存能力.由于机翼内部结构复杂,很难对含离散源损伤机翼结构进行精确分析,而且精确的建模和仿真在建模与计算过程中往往也非常耗时.因此,以含离散源损伤机翼为对象,采用有限元优化设计方法,确立了一种机翼结构等效板模型的建模方法.建立的等效板模型可对含离散源损伤机翼实现快速、准确的静力学和动力学分析.