激光测高仪回波分解算法

开发了一种激光测高仪回波基本信息提取算法,对回波数据进行了高斯波分解,获取了高斯波分量的个数,及每个高斯波分量的波中心位置、宽度和幅度等参数．该算法首先根据回波拐点的数目和位置确定出高斯分量的个数及每个高斯分量的波中心位置和宽度初始值,随后利用线性最小二乘法计算出每个高斯分量的幅度,最后将经过选择和标记的高斯分量针对实际回波采用Levenberg-Marquardt方法进行拟合,得到优化后的高斯波基本参数．通过这些基本参数信息,能够进一步推导出激光测高仪光斑内各个反射表面的垂直分布、起伏程度和反射率等基本信息．     

抛物形吸气式脉冲爆震激光推力器性能预示的解析模型

考虑激光束、推力器构型以及大气环境三方面因素,建立了抛物形吸气式脉冲爆震 激 光推力器性能预示的解析计算模型。其中,将推力室内的流场发展过程分为吸收波和冲击波 衰减两个阶段,应用Sedov点爆炸理论,以等效锥形约束空间,引入单一的修正因子以反 映流场的不均匀性。计算表明,其结果同现有实验数据吻合。〖JP〗     

燃气轮机周向拉杆转子连接刚度对转子振动特性影响的研究

为研究燃气轮机周向分布式拉杆转子轮盘间存在的连接刚度对轴系转子振动特性产生的影响,本文提出一种基于六自由度的弹簧单元等效方法;首先将轮盘接触刚度与拉杆弯曲刚度同时等效进连接界面,便于使用一维梁单元求解其临界转速与振动响应变化,验证其与全三维有限元法吻合度在3％以内;然后改写了非线性动力学方程,采用谐波平衡法对其进行求解,使用经典Newmark方法验证其准确性;最后使用该等效方法计算了某模拟转子连接刚度对其临界转速、响应特性、非线性特性等的影响。计算结果表明：当连接面剪切刚度与弯曲刚度减小3个数量级,均造成了临界转速的降低和振动响应的提高,而其影响程度可由各阶振型大致推测,且响应幅值受剪切刚度影响较大;使用临界转速趋于收敛时的连接刚度与试验值的对比误差小于2％,较连续模型提升显著;在连接刚度各向异性时,每一阶临界转速均出现两个响应峰值,轴心轨迹变成椭圆;考虑刚度随位移变化（非线性刚度）后,转子的响应峰值发生“歪扭”特性,且该峰值特征随不平衡量、无量纲阻尼等因素变化而呈现“波浪形”变化。     

基于正交试验的超声波喷丸成形工艺参数分析及弧高值预测

针对带筋板的超声波喷丸成形,采用正交试验法研究了撞针速度、撞针直径、成形轨迹间距、喷丸区域宽度对带筋板超声波喷丸成形弧高值的影响,得出最佳参数组合方案,并以此作为样本数据,建立多元回归分析数学模型。通过实验验证模型的准确性,试验数据和回归分析数据相符较好,可以用回归分析的数学模型来预测喷丸弧高值,提高工艺设计效率。     

Dependence on forming parameters of an integral panel during the electromagnetic incremental forming process

Nowadays, more and more attentions are paid to electromagnetic incremental forming(EMIF), especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X" discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z" discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.     

激光陀螺误差分析的Allan方差法改进研究

针对传统Allan方差法分析激光陀螺误差特性过程中,不能合理解释方差中部分噪声项出现负值的情况,而采用阻尼振荡的分析方法能够对此给出合理解释,却又损失了辨识精度的问题,提出了一种基于动态Allan方差法理论的改进Allan方差法。该方法将阻尼振荡模型与动态Allan方差模型相结合,使得辨识结果的分析过程更加合理。激光陀螺零偏误差的辨识与分析结果表明:改进Allan方差法的辨识结果精度略高些,在改进Allan方差的三维分析图中可以显示出零偏中存在的数据突变情况,能够反应激光陀螺误差的动态特性。因此,改进Allan方差法更适用于激光陀螺误差特性的分析。     

AZ31镁合金板热成形中的屈服和损伤:本构实现与数值分析

为了准确预测各向异性镁合金板的成形质量,将改进的GTN损伤模型与各向异性拉压不对称的CPB06屈服本构耦合,并考虑了屈服面形状随塑性应变累积的变化,得到了考虑本构参数随塑性应变演化的各向异性屈服CPB06-GTN损伤模型。基于该模型,在ABAQUS/Explict中编译得到了相应的VUMAT子程序,采用单个单元进行了单轴拉伸和压缩模拟,并通过与实验一致性对比验证了子程序的正确性。使用子程序不仅能够模拟镁合金的各向异性屈服及其不规则的硬化,同时也能够模拟镁合金的损伤破坏。此外,采用编写的子程序进行了热拉深成形的数值模拟,模拟预测与实验结果对比表明,采用各向异性损伤模型的计算结果能够准确预测镁合金的变形及其损伤破坏,模拟结果与实验数据吻合;采用合适的压边力和成形的温度条件及非等温成形方法能够提高镁合金的成形性。     

薄壁大尺寸铌钨合金喷管精密旋压成形工艺研究

通过对铌钨合金性能的研究,得到了铌钨合金一次旋压最大减薄率,采用变厚度平板旋压毛坯,合理分布两次剪切旋压变形量和各点壁厚变薄率,控制旋压过程,应用仿真软件对翻边成形进行仿真,掌握了薄壁大尺寸铌钨合金喷管精密旋压及翻边成形技术.     

Towards intelligent design optimization: Progress and challenge of design optimization theories and technologies for plastic forming

Plastic forming is one of enabling and fundamental technologies in advanced manufacturing chains. Design optimization is a critical way to improve the performance of the forming system, exploit the advantages of high productivity, high product quality, low production cost and short time to market and develop precise, accurate, green, and intelligent (smart) plastic forming technology. However, plastic forming is quite complicated, relating to multi-physics field coupling, multi-factor influence, multi-defect constraint, and triple nonlinear, etc., and the design optimization for plastic forming involves multi-objective, multi-parameter, multi-constraint, nonlinear, high-dimensionality, non-continuity, time-varying, and uncertainty, etc. Therefore, how to achieve accurate and efficient design optimization of products, equipment, tools/dies, and processing as well as materials characterization has always been the research frontier and focus in the field of engineering and manufacturing. In recent years, with the rapid development of computing science, data science and internet of things (IoT), the theories and technologies of design optimization have attracted more and more attention, and developed rapidly in forming process. Accordingly, this paper first introduced the framework of design optimization for plastic forming. Then, focusing on the key problems of design optimization, such as numerical model and optimization algorithm, this paper summarized the research progress on the development and application of the theories and technologies about design optimization in forming process, including deterministic and uncertain optimization. Moreover, the applicability of various modeling methods and optimization algorithms was elaborated in solving the design optimization problems of plastic forming. Finally, considering the development trends of forming technology, this paper discusses some challenges of design optimization that may need to be solved and faced in forming process.     

螺栓连接结构接触面刚度识别方法

针对线性范围内的螺栓连接结构开展研究。在薄层单元理论基础上,提出了一种螺栓连接结构接触面刚度识别方法。采用正交各向异性本构关系的薄层单元模拟接触面,忽略螺栓和螺孔的影响,建立单个螺栓和多个螺栓搭接2种结构的初始有限元模型;根据试验模态参数,识别连接部位薄层单元材料参数。识别后,2种连接结构前四阶模态频率的计算结果最大误差不超过3.5%,表明识别后的薄层单元能准确反映接触界面的力学特征;文中方法适用于单个螺栓搭接和螺栓较密集工况的准确模拟。