超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

A user-friendly yield criterion for metals exhibiting tension-compression asymmetry

The aim of this paper is to model the yielding asymmetry of pressure-insensitive metals, including but not limited to Ni₃Al alloys. The main focuses are put on the flexibility and manipulative convenience. The parameters of theory are kept to a minimum and can be determined by as few tests as possible. These requirements are fulfilled by constructing a yield function using the second and third-invariants of a linearly transformed stress tensor. The proposed yield criterion has a simple mathematical form and has only seven parameters when used in three-dimensional stresses. Compared with existing theories, the new yield criterion has much fewer parameters, which makes it very convenient for practical applications. The coefficients of the criterion are identified by an error minimization procedure. Applications to a Ni₃Al based intermetallic alloy as well as a Cu-Al-Be shape memory alloy and comparison to other criteria show that the proposed criterion has nearly the same predictive ability and flexibility with other criteria. The proposed yield criterion can estimate the coefficients by using less data, which is a big advantage compared with other similar theories, especially when there is a limited number of experimental data.     

Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist

The application of surface textures has been employed to improve the tribological performance of various mechanical components. Various techniques have been used for the application of surface textures such as micro-dimple arrays, but the fabrication of such arrays on cylindrical inner surfaces remains a challenge. In this study, a dry-film photoresist is used as a mask during through-mask electrochemical micromachining to successfully prepare micro-dimple arrays with dimples 94 lm in diameter and 22.7 lm deep on cylindrical inner surfaces, with a machining time of 9 s and an applied voltage of 8 V. The versatility of this method is demonstrated, as are its potential low cost and high efficiency. It is also shown that for a fixed dimple depth, a smaller dimple diameter can be obtained using a combination of lower current density and longer machining time in a passivating sodium nitrate electrolyte.     

考虑流固耦合效应的航空发动机风扇叶片应力数值模拟与试验测量研究

航空发动机风扇转子在高压比、高转速、高负荷的级环境中工作时,存在叶片固体域与流体域之间强烈的耦合作用。针对风扇工作中的流固耦合问题,采用基于流固耦合的数值模拟方法对风扇叶片的结构特性进行模拟,研究考虑流固耦合效应前后叶片结构特性的变化。通过风扇转子加减速试验测量叶片表面测点应力变化,并将数值模拟与试验测量结果进行了对比分析。分析结果表明：考虑流固耦合效应后叶片表面的受力情况变化较大,导致叶片表面的应力与变形分布产生较大的变化;仅考虑离心力作用的计算方法得到的应力值与试验测量值误差最大达到50%,而考虑流固耦合效应的计算值误差在10%左右;考虑叶片流固耦合效应得到的应力分布更满足实际工程应力与强度分析要求。     

三维光弹性测定应力强度因子K_Ⅰ的综合法

对利用三维光弹性试验数据计算应力强度因子K_I,提出一种新的算法--综合法。此法既解决了所需测量区域内条纹信息少的弱点,又克服了因裂纹尖端“钝化”而无法测到裂尖精确条纹值的困难。试验与计算结果表明此法误差小、精度最高。可应用测定受复杂载荷并具有复杂边界条件结构的应力强度因子。     

交变应力下冷胀孔边残余应力衰减规律的有损检测试验研究

对高胀孔量下的ＬＹ１２ＣＺ板件孔边残余应力在交变应力作用下衰减规律的有损多试件普通莫尔密栅云纹检测方法进行了尝试,给出了一定载荷范围内残余应力的衰减规律,揭示了高胀孔量下残余应力的再分布现象。研究表明,本文所使用的多试件有损检测方法,不但经济可行,而且有足够精度,应用前景十分广阔。     

GC－4高强度钢化学短裂纹特性研究

采用恒ΔＫ法对ＧＣ－４钢在３．５％ＮａＣｌ溶液中化学短裂纹特性进行了试验研究。结果表明：恒ΔＫ时裂纹扩展的ｄａ／ｄＮ－ａ曲线存在临界裂纹尺寸ａ。当ａ＜ａ时,显示化学短裂纹效应。ａ值几乎不受加载频率、应力比和ΔＫ水平的影响;化学短裂纹特征扩展速率与长裂纹扩展速率之比是各种力学参量的弱函数。依据分析给出化学短裂纹扩展速率与裂纹尺寸之间的关系。     

含不等长双裂纹无限大板应力强度因子

采用交替法求解了含任意相对位置不等长双裂纹的无限大极受均布拉应力作用的应力强度因子。此法以平面弹性力学的一个问题为基础,即含单裂纹无限大板,裂纹面受集中载荷,此问题的解已知,然后交替地满足边界条件。各种计算结果已绘成曲线。