横向互击型层板喷注器的喷雾特性

利用激光粒子动态分析仪 (PDA)对 180°互击型层板式喷注器的喷雾特性进行了试验研究 ,测量了喷雾典型区域的液滴速度、直径、体积通量密度等参数。分析了喷注器的雾化过程和喷雾特点 ,同时重点研究了喷口槽宽、推进剂流道面积比以及推进剂喷注速度比等参数对喷雾特性的影响。试验结果表明 :喷雾沿喷口展向可分为三个明显区域 ,中间区域流量较小但雾化较细 ,从槽两端喷出的液雾流量较大但液滴尺寸较大。对于一定的流道截面比γd 和喷注速度比γv,存在一个最佳的喷嘴槽宽w使雾化质量最优。同时 ,在喷嘴槽宽合适时 ,流道截面比γd 和喷注速度比γv 的适当增大有利于改善雾化     

异型孔空心叶片壁厚检测的试验研究

发动机叶片的结构型式和制造误差，直接影响发动机的性能和使用寿命。运用超声波法和电涡流法，对两种不同材料和形式的试件进行了试验。电涡流法受到探头直径和试件几何尺寸的影响，测量误差大，超声波法由于存在测量盲区，测量厚度的下限受到限制。但测量值与实际值相关，若对探头加以改进，用于异型孔空心叶片壁厚检测是可行的。     

Spectra and time variability of black-hole binaries in the low/hard state

We propose a jet model for the low/hard state of galactic black-hole X-ray sources which explains the energy spectra from radio to X-rays and a number of timing properties in the X-ray domain such as the time lag spectra, the hardening of the power density spectra and the narrowing of the autocorrelation function with increasing photon energy. The model assumes that (i) there is a magnetic field along the axis of the jet, (ii) the electron density in the jet drops inversely proportional to distance, (iii) the jet is “hotter” near its center than at its periphery, and (iv) the electrons in the jet follow a power-law distribution function. We have performed Monte Carlo simulations of Compton upscattering of soft photons from the accretion disk and have found power-law high-energy spectra with photon-number index in the range 1.5–2 and cutoff at a few hundred keV, power-law time lags versus Fourier frequency with index 0.8, and an increase of the rms amplitude of variability and a narrowing of the autocorrelation function with increasing photon energy as they have been observed in Cygnus X-1. The spectrum at long wavelengths (radio, infrared, optical) is modeled to come from synchrotron radiation of the energetic electrons in the jet. We find flat to inverted radio spectra that extend from the radio up to about the optical band. For magnetic field strengths of the order 10⁵–10⁶ G at the base of the jet, the calculated spectra agree well in slope and flux with the observations.     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

微小孔特种加工技术研究现状及展望

近年来微小孔结构在航空航天零部件上的应用越来越广泛,对微小孔的特种加工方法的进展情况进行了综述,总结了每种加工方法的主要特点,并对当前微小孔特种加工技术存在的问题及未来发展趋势进行了总结和展望.     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

背压对撞击式喷嘴雾化特性影响研究

为研究背压对撞击式喷嘴雾化特性的影响,将压力的变化等效为气体密度的变化,基于一种树形自适应加密算法,通过直接数值求解不可压Navier-Stokes方程组实现了不同背压条件下射流撞击雾化的数值模拟。首先将数值模拟结果与试验数据进行对比,验证数值模拟的有效性,在此基础上开展了高背压条件下雾化过程的数值模拟。结果表明,随着背压的提高,气动力相应增强,液膜的破碎更加剧烈,一次雾化区域的液滴数密度增大,雾场由稀疏向稠密发展;液膜在向下游运动过程中波动速度的幅值逐渐增大,并且随着背压的提高,液膜的波动由线性向非线性转变;背压增大导致破碎长度减小,经过参数修正得到了液膜破碎长度的经验公式,并与试验数据进行了对比;背压对液滴尺寸分布规律没有显著影响,但随着背压的提高,同一时刻大液滴所占的比例提高,整个雾场的Sauter平均直径有增加的趋势,当背压从0.1MPa增大到1MPa时,雾场的Sauter平均直径由155.5μm增大到166.9μm;背压增大,液滴粒径分布的均匀度指数减小,液滴尺寸分布更加不均匀。     

活门型孔“化方为圆”算法

通过对航空发动机控制系统活门型孔的流量系数稳定性控制的方法进行研究,提出了一套能够将方形活门型孔转化为有规律排列组合小圆孔的算法,并通过实例验证了算法的正确性,同时转化误差小于0.7%,基本实现了工程意义上的等流量系数。该算法将加工工艺性差且计量精度低的方形活门型孔转化为有规律排列组合小圆孔,消除了方形型孔流量系数变化的影响,改变了活门型孔加工方法,减少了对人和环境的危害,提高了活门型孔的计量精度,减小了活门的液动力,具有极大的工程应用价值。 该算法可以实现将方形、梯形（含三角形）及其组合型孔等任意型孔的转化,具有工程上的普遍适用性。