基于天基光学探测图像初析南大西洋异常区影响

文章针对目前在轨运行的高灵敏度探测类可见光遥感器经过南大西洋异常区（SouthAtlanticAnomaly,SAA）时出现的探测能力降低、目标无法识别等现象,通过卫星在轨获取的SAA天基探测图像研究图像中出现的异常现象机理;提出了基于CCD探测器固有暗像元区的图像特征变化开展SAA影响评估的方法,根据在轨图像暗像元区的均值和标准差、图像区的热像素及活像元等特征参数的统计分析,判断经过SAA过程中连续获取的图像中出现显著影响时的拐点,通过曲线拟合估算出该轨道高度的SAA空间分布特征和边界,依此进一步提出利用在轨天基探测图像给出测量影响该轨道高度卫星SAA区域边界的简单方法;最后,基于SAA对天基探测器件的影响分析结果和认识,给出了高灵敏度探测类卫星避免或消除SAA影响的改进措施和建议。文章采用的数据分析和评估方法为提升SAA对天基探测影响的认识,以及下一步有效开展空间碎片探测工作提供参考。     

固溶时效处理对高强高韧钛合金显微组织与力学性能的影响

对固溶时效处理后的高强高韧钛合金初生α相的体积分数、尺寸,次生α相的体积分数和α_s/β相界面密度等显微组织特征进行了定量表征和统计分析,探讨了随着固溶温度的变化,高强高韧钛合金显微组织与其力学性能间的相关性.结果表明:在α+β两相区固溶时效处理,随着固溶温度的升高,合金初生α相的体积分数降低,相尺寸先降低后略有升高,次生α相的体积分数升高,α_s/β相界面密度先升高后降低.初生α相的体积分数与伸长率、静力韧度和裂纹形成功正相关,α_s/β相界面密度与合金屈服强度成正相关.      

超声速预混气的热射流起爆过程数值模拟

采用带有化学反应的Euler方程,对超声速预混气的热射流起爆过程进行了研究。在来流速度大于CJ(Chapman-Jouguet)爆震速度的情况下,射流所导致的弓形激波在爆震波起爆过程中起到了重要作用,而爆震波不稳定性导致横波的产生是决定能否完全起爆的关键因素。射流角度的改变能够影响到起爆的过程与驻定性质。随着射流角度的逐渐减小,会出现起爆后驻定、起爆后不能驻定以及起爆失败三种结果。     

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

Twaron纤维的新型化学活化方法

以傅瑞德-克拉夫茨(Friedel-Crafts)反应为基础,活化处理Twaron纤维的惰性表面。对经过活化处理的Twaron纤维进行了单丝拔出(SFP)、X射线衍射(XRD)、扫描电镜(SEM)、红外图谱(FTIR)、表面电子能谱(XPS),以及表面自由能等测试。测试结果显示,经过活化处理后,Twaron纤维表面因环氧基团的接枝而使表面自由能显著增加;纤维表面的结晶结构未发生显著改变,纤维的本体强度未降低;相对应的环氧树脂基复合材料的单丝拔出强度提高了约50%。     

ZnO透明导电薄膜制备及紫外辐照处理特性研究

ZnO作为一种典型的透明导电氧化物（Transparent conductive oxide,TCO）材料,具有同氧化铟锡(Indium tin oxide,ITO)相比拟的光电性能,其原料丰富、绿色环保、易于制备、生成成本低等优点使ZnO成为最有希望替代ITO的材料。本文以玻璃为衬底,利用量子点种子层作为缓冲层,采用传统水热方法制备了低成本ZnO透明导电薄膜,采用特殊的紫外光辐照工艺对薄膜进行后处理,探索薄膜生长参数和紫外光辐照处理工艺对其透光率和导电性的影响。结果表明,紫外辐照处理不影响薄膜的透光性能,而使材料的方块电阻降低3个数量级,数值从没处理时的1.5×105 Ω/□降低到 150 Ω/□,极大地提高了薄膜的电导率,为ZnO薄膜材料电导率的提高提供了一个简单高效的途径。     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

MA 及原位-热压合成TiC/ Ti5 Si3 复合材料

以Ti粉、Si粉和C粉为原料,利用高能球磨及热压工艺合成了TiC/Ti5Si3陶瓷复合材料。研究了工艺条件尤其是热压温度对合成产物相组成及微观结构的影响,并结合DSC、XRD和SEM对反应合成机理进行探讨。结果表明:通过优化合成工艺,高能球磨12 h,热压温度1 400℃时,烧结6 h得到了高纯度的TiC/Ti5Si3陶瓷复合材料;合成过程为:反应开始时发生Ti+C■TiC,反应ΔG=-167.72 kJ/mol。2 h时发生5TiC+8Si■Ti5Si3+5SiC,反应ΔG=-62.12 kJ/mol,当6 h时发生3SiC+8Ti■Ti5Si3+3TiC,反应ΔG=-697.8 kJ/mol。显微结构表明:TiC/Ti5Si3复合材料的合成过程伴随Si熔融,该材料以TiC-Si-Ti5Si3形式相结合,其中Si为黏结剂。     

均匀化处理对TiAl 合金铸造组织的影响

研究了均匀化处理对两种含B的铸造TiAl合金铸造组织的影响。研究发现1 370℃/5 min/OQ+1150℃/6 h/AC均匀化热处理能有效消除B2相,将b稳定化元素固溶到基体中,实现成分均匀化;1 370℃/5 min/OQ+1 150℃/24 h/AC均匀化热处理后可使粗大的铸造片层组织分解转变为细晶近g组织,平均晶粒直径50mm。     

自适应流通机匣处理改善压气机性能的机理

为了探索自适应流通机匣处理形式影响跨声压气机性能及流场的流动机理,文中采用非定常数值模拟方法研究了自适应流通机匣处理对NASA轴流Rotor37气动性能的影响。数值计算结果表明:自适应流通机匣处理能有效地延迟失速并在大部分流量范围内略微提高压气机的效率。通过详细的流场分析表明,该机匣处理能有效地增大叶顶区的气流进气角度,抑制了间隙泄漏涡在叶顶通道内的发展,同时阻止泄漏涡涡核在通过激波后破碎,提高了转子顶部通道的流通能力,进而减少叶顶区的流动损失。