小半径弯管弯胀复合成形研究

为解决小半径弯管内侧起皱、外侧减薄的成形缺陷,提出了一种弯胀复合成形的方法。通过几何关系解析了初始弯曲半径和初始管坯直径与最终管径和最终弯曲半径之间的关系,确定了初始弯曲半径的取值范围。采用有限元与实验相结合的方式研究了不同初始弯曲半径对零件壁厚分布的影响,分析了胀形过程中零件弯曲处及直壁处的变形规律。最终发现:初始弯曲半径越大,零件的最终减薄越小,胀形过程中弯曲处内外侧发生均匀减薄,直壁处内侧减薄明显大于外侧减薄。     

发动机喷流对飞行器底部流动影响数值模拟

针对发动机燃气喷流对底部流动的影响开展研究。建立冷喷与热喷计算方法，与经典的高压空气尾喷管喷流试验数据进行了对比，验证了本文建立的三维喷流方法的可靠性。对本文选用的飞行器外形采用冷喷与热喷方法开展了对比计算并与飞行试验值进行比较，分析了两种方法结果的差异。采用热喷方法对来流马赫数 2.5 ，不同飞行高度及喷管进口总压开展计算，研究飞行高度及喷管进口总压对发动机喷流及底部流场的影响。结果表明，保持飞行高度、来流马赫数不变，喷管进口总压增加，底部压力系数逐渐提高。燃气质量浓度最大值位于底部空腔的壁面处，且保持一个恒定值。保持喷管进口总压、来流马赫数不变，飞行高度增加，喷流高速区向后移动且中心区最大马赫数增加。在一定飞行高度下，底部压力系数由负转正，即飞行器底部会出现正推力，这对飞行器的射程会产生重要影响，需要提前评估。     

航天铝合金深腔零件整体成形预制坯优化设计

提出航天铝合金深腔零件整体成形方法,开展预制坯优化设计。对比分析直筒和变径筒两种预制筒坯结构变形规律,数值模拟研究了底部圆角对开口球形件液压成形的影响规律。以直径D=450 mm的球形整体零件为验证对象,进行底部圆角r=60 mm的变径筒形件的液压成形试验验证。结果表明:直筒坯液压成形时,赤道位置发生破裂;变径筒坯液压成形时,当胀形压力为16 MPa即发生贴模;液压成形时,筒端口自适应补料,所以上半球的壁厚分布均匀;随着底部圆角越大,筒底部减薄越小,筒壁厚越均匀;当底部圆角为r=60 mm时,开口球壳赤道位置壁厚减薄最严重,减薄率为11.1%,球底部减薄率为9.8%,开口球壳上半球壁厚差为0.17 mm,下半球壁厚差为0.43 mm。     

热等静压对激光选区熔化成形GH4169合金持久性能的影响

采用激光选区熔化(SLM)成形技术制备了GH4169合金,运用金相显微镜(OM)、扫描电子显微镜(SEM)、电子背散射衍射(EBSD)和透射电镜(TEM)等分析手段分析了热等静压对SLM成形GH4169合金组织及持久性能的影响规律。结果表明:沉积态合金组织中,沿沉积方向的晶粒为柱状晶,晶粒内枝晶组织细小,枝晶间分布大量Laves相;热等静压处理可有效消除组织中气孔缺陷,溶解大部分Laves相,促使组织晶粒等轴化,并减少后续980℃固溶处理过程中δ相在晶内的析出;热等静压处理能提高合金的持久寿命,但会降低合金的持久塑性。     

基于正交试验的超声波喷丸成形工艺参数分析及弧高值预测

针对带筋板的超声波喷丸成形,采用正交试验法研究了撞针速度、撞针直径、成形轨迹间距、喷丸区域宽度对带筋板超声波喷丸成形弧高值的影响,得出最佳参数组合方案,并以此作为样本数据,建立多元回归分析数学模型。通过实验验证模型的准确性,试验数据和回归分析数据相符较好,可以用回归分析的数学模型来预测喷丸弧高值,提高工艺设计效率。     

Dependence on forming parameters of an integral panel during the electromagnetic incremental forming process

Nowadays, more and more attentions are paid to electromagnetic incremental forming(EMIF), especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X" discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z" discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.     

AZ31镁合金板热成形中的屈服和损伤:本构实现与数值分析

为了准确预测各向异性镁合金板的成形质量,将改进的GTN损伤模型与各向异性拉压不对称的CPB06屈服本构耦合,并考虑了屈服面形状随塑性应变累积的变化,得到了考虑本构参数随塑性应变演化的各向异性屈服CPB06-GTN损伤模型。基于该模型,在ABAQUS/Explict中编译得到了相应的VUMAT子程序,采用单个单元进行了单轴拉伸和压缩模拟,并通过与实验一致性对比验证了子程序的正确性。使用子程序不仅能够模拟镁合金的各向异性屈服及其不规则的硬化,同时也能够模拟镁合金的损伤破坏。此外,采用编写的子程序进行了热拉深成形的数值模拟,模拟预测与实验结果对比表明,采用各向异性损伤模型的计算结果能够准确预测镁合金的变形及其损伤破坏,模拟结果与实验数据吻合;采用合适的压边力和成形的温度条件及非等温成形方法能够提高镁合金的成形性。     

薄壁大尺寸铌钨合金喷管精密旋压成形工艺研究

通过对铌钨合金性能的研究,得到了铌钨合金一次旋压最大减薄率,采用变厚度平板旋压毛坯,合理分布两次剪切旋压变形量和各点壁厚变薄率,控制旋压过程,应用仿真软件对翻边成形进行仿真,掌握了薄壁大尺寸铌钨合金喷管精密旋压及翻边成形技术.     

基于天基光学探测图像初析南大西洋异常区影响

文章针对目前在轨运行的高灵敏度探测类可见光遥感器经过南大西洋异常区（SouthAtlanticAnomaly,SAA）时出现的探测能力降低、目标无法识别等现象,通过卫星在轨获取的SAA天基探测图像研究图像中出现的异常现象机理;提出了基于CCD探测器固有暗像元区的图像特征变化开展SAA影响评估的方法,根据在轨图像暗像元区的均值和标准差、图像区的热像素及活像元等特征参数的统计分析,判断经过SAA过程中连续获取的图像中出现显著影响时的拐点,通过曲线拟合估算出该轨道高度的SAA空间分布特征和边界,依此进一步提出利用在轨天基探测图像给出测量影响该轨道高度卫星SAA区域边界的简单方法;最后,基于SAA对天基探测器件的影响分析结果和认识,给出了高灵敏度探测类卫星避免或消除SAA影响的改进措施和建议。文章采用的数据分析和评估方法为提升SAA对天基探测影响的认识,以及下一步有效开展空间碎片探测工作提供参考。     

Towards intelligent design optimization: Progress and challenge of design optimization theories and technologies for plastic forming

Plastic forming is one of enabling and fundamental technologies in advanced manufacturing chains. Design optimization is a critical way to improve the performance of the forming system, exploit the advantages of high productivity, high product quality, low production cost and short time to market and develop precise, accurate, green, and intelligent (smart) plastic forming technology. However, plastic forming is quite complicated, relating to multi-physics field coupling, multi-factor influence, multi-defect constraint, and triple nonlinear, etc., and the design optimization for plastic forming involves multi-objective, multi-parameter, multi-constraint, nonlinear, high-dimensionality, non-continuity, time-varying, and uncertainty, etc. Therefore, how to achieve accurate and efficient design optimization of products, equipment, tools/dies, and processing as well as materials characterization has always been the research frontier and focus in the field of engineering and manufacturing. In recent years, with the rapid development of computing science, data science and internet of things (IoT), the theories and technologies of design optimization have attracted more and more attention, and developed rapidly in forming process. Accordingly, this paper first introduced the framework of design optimization for plastic forming. Then, focusing on the key problems of design optimization, such as numerical model and optimization algorithm, this paper summarized the research progress on the development and application of the theories and technologies about design optimization in forming process, including deterministic and uncertain optimization. Moreover, the applicability of various modeling methods and optimization algorithms was elaborated in solving the design optimization problems of plastic forming. Finally, considering the development trends of forming technology, this paper discusses some challenges of design optimization that may need to be solved and faced in forming process.