耐温400℃、低损耗改性氰酸酯载体胶膜的制备及性能

采用双酚E型氰酸酯树脂(BECE)和端羟基聚醚砜(Mx)共改性酚醛型氰酸酯树脂(NovolacCE),并将其与石英布复合制备出了一种耐温400℃、低损耗的改性氰酸酯载体胶膜。结果表明,适量的BECE和Mx热混合加入Novolac-CE树脂中,改善了Novolac-CE的浸润性和韧性,其与石英纤维的接触角降至72.8°,冲击韧性提高到13 kJ/m~2。相比于没经过处理的石英布,经过0.5%KH550/乙醇溶液处理的石英布与Novolac-CE树脂间的粘接强度最大提高70%,但是过多的KH550加入影响胶膜的耐热性。胶膜经200℃/4 h固化后,400℃时剪切强度大于5 MPa,且连续使用60 min后强度保持率大于80%,介电损耗为0.014。胶膜具有良好的自黏性并且室温适用期大于15 d,可作为耐高温(400℃)透波粘接材料应用。     

固化工艺参数对聚酰亚胺复合材料性能影响

采用热压罐成型工艺制备了MT300/902聚酰亚胺复合材料,测试了加压温度、加压大小和固化温度下复合材料的力学性能,分析了不同固化工艺参数对复合材料力学性能的影响规律。结果表明:MT300/902聚酰亚胺复合材料固化时的最佳加压时机为240～260℃、加压不小于1.2 MPa、固化温度在310～330℃为最佳。按照最优的成型工艺参数制备的复合材料构件质量高,缺陷能够控制在2%以下,力学性能进一步提高。     

基于频域参量的石英复合材料孔隙超声表征方法研究

孔隙率对复合材料性能有很大影响。针对高孔隙率复合材料超声表征不足问题,本文把超声功率谱特征和非线性特征应用于表征高孔隙石英酚醛复合材料的孔隙率,即在频域上对比研究孔隙对基波幅值的衰减及谐波幅值的滋生的影响。结果表明:二者均能有效表征高孔隙复合材料的孔隙率。基于频域基波分析的超声功率谱特征参量测量容易,随孔隙增加呈递减变化,在孔隙率较低时具有一定优势;基于谐波分析的超声二阶非线性特征参量,随孔隙增加呈递增变化,对高孔隙率表征更具优势。     

航空齿轮磨削加工安装偏心误差补偿研究

磨齿加工时齿坯几何中心与回转工作台轴心存在安装偏心误差,降低了磨齿加工精度。以数控成型砂轮磨齿机工作原理为基础,建立偏心误差磨削加工几何模型;提出安装偏心误差补偿法,建立偏心误差补偿数学模型,通过数学模型求出磨削砂轮在X、Y两个方向的进给补偿增量;以YK73125数控成型砂轮磨齿机为例,进行安装偏心误差补偿实验,齿轮的左右齿面单个齿距极限偏差绝对值分别减小了0.9μm和1.6μm,齿距累积总偏差绝对值分别减小了49.6μm和43.3μm。结果表明:安装偏心误差与单个齿距偏差和齿距累积总偏差成正比;采用安装偏心误差补偿进行磨齿加工,有效地减小了单个齿距偏差和齿距累积总偏差,齿轮的精度有所提高。     

Time delay compensation in lateral-directional flight control systems at high angles of attack

The previous studies of time delay compensation in flight control systems are all based on the conventional aerodynamic derivative model and conducted in longitudinal motions at low angles of attack. In this investigation, the effects of time delay on the lateral-directional stability augmentation system in high-α regime are discussed based on the $\dot{\beta }$ model, which is proposed in our previous work and proved as a more accurate aerodynamic model to reveal the lateral-directional unsteady aerodynamic characteristics at high angles of attack. Both the $\dot{\beta }$ model and the quasi-steady model are used for simulating the effects of time delay on the flying qualities in high-α maneuvers. The comparison between the simulation results shows that the flying qualities are much more sensitive to the mismatch of feedback gains than the state errors caused by time delay. Then a typical adaptive controller based on the conventional dynamic derivative model and a gain-prediction compensator based on $\dot{\beta }$ model are designed to address the time delay in different maneuvers. The simulation results show that the gain-prediction compensator is much simpler and more efficient at high angles of attack. Finally, the gain-prediction compensator is combined with a linearized $\dot{\beta }$ model reference adaptive controller to compensate the adverse effects of very large time delay, which exhibits excellent performance when addressing the extreme conditions at high angles of attack.     

高精度高动态星模拟器研究

给出了高精度高动态星模拟器系统组成和总体结构, 提出一种基于亚像素显示技术提高动态星模拟器星点位置显示精度从而减小星点几何中心与能量中心位置偏差的新方法. 针对动态星模拟器高动态性要求, 提出一种快速精确检索全天球导航星的新方法, 将已知SAO (Smithsonian Astrophysical Observatory) 星表进行分区, 计算当前姿态四元数并分析航天器视轴所在区域, 对于距离视轴较远区域停止搜索和匹配, 很大程度上缩小了导航星搜索范围, 进而缩短了全天球恒星遍历所需时间. 软件测试结果表明, 此快速检索法可使全天球导航星的选取速度提高近10倍.      

FY-3A卫星星内辐射剂量评估与分析

对FY-3A卫星近四年的辐射剂量数据进行分析,结果表明,在1 mm铝的等效屏蔽厚度下,星内辐射剂量存在显著的方向性差异,+Y向剂量增长变化显著大于+Z向.深入分析剂量变化与带电粒子辐射关系后发现,太阳质子事件期间的高能质子增长不会对辐射剂量增长变化产生显著影响;而高能电子是剂量增长变化的主要贡献者,其中扰动导致的高能电子通量强增长是使得辐射剂量显著增加的主要原因,并显著影响到卫星+Y向.进一步与工程常用SPENVIS剂量计算结果的对比表明,实测能更好地反映剂量动态变化和方向差异.综上,实测剂量数据对于同类工程星内器件的合理布局和工程防护设计具有一定指导和参考价值.     

辐射带高能电子通量波动与地磁暴警报

地球磁场捕获带电粒子形成辐射带,地磁场的扰动将导致带电粒子通量的变化.根据磁暴期间外辐射带高能电子通量起伏和波动的特点及规律,利用GOES卫星实时发布的5min分辨率高能电子微分通量数据,构建了高能电子通量波动指数,并分析了该指数与地磁活动的关系.结果表明,所提出的高能电子通量波动指数与地磁事件有很好的相关性,能起到地磁暴发生的指示剂作用,相对于目前空间环境业务化预报过程中广泛使用的3hKp指数,高能电子通量波动指数能更早地警报地磁暴的发生,是潜在有效的地磁暴警报辅助手段,能为空间环境预报中的地磁暴实时警报提供重要参考.      

一种融合MRF分割与数学形态学的道路提取算法

针对高分辨率合成孔径雷达（Synthetic Aperture Radar, SAR）图像中道路目标难以有效提取的问题,提出一种融合马尔可夫随机场（Markov Random Field, MRF）分割与数学形态学处理的高分辨率SAR图像道路提取算法。该算法首先利用直方图均衡化和增强Lee滤波对SAR图像进行预处理,实现道路的边缘增强,抑制相干斑噪声;进而利用基于条件迭代模式（Iterated Conditional Mode, ICM）的MRF对SAR图像中的道路目标进行初分割;再用数学形态学填充空洞,平滑道路边缘;最后,基于道路的几何特征,使用偏心率、矩阵度、复杂度等因子去除虚警,从而提取出道路目标。利用该文算法对两块实际高分辨率SAR图像进行道路目标提取,均可以取得90%以上的正确道路提取率,表明本文算法具有较高的道路提取精度。     

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.