基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

下缘板孔对涡轮叶片尾缘内冷通道流动换热影响的数值研究

涡轮叶片下缘板出气孔对内冷通道的流动和换热性能有较大影响。通过数值模拟方法研究下缘板出 气孔对尾缘和下缘板双路出气涡轮叶片尾缘内冷通道内的流动和换热特性,对比分析孔径、孔形和孔位置对尾 缘溢流孔流量系数、尾缘出流比、尾缘通道内总压系数和尾缘内冷腔壁面换热特性的影响。结果表明:下缘板 出气孔孔径对流量系数分布的影响显著,孔径增大,尾缘溢流孔流量系数下降,尾缘出流比减小,尾缘内冷通道 内压力损失降低,内冷腔平均换热系数增大;孔形对上游内冷通道内流动和换热几乎没有影响;孔位置变化对 内冷通道壁面整体的换热系数影响很小,对局部影响较大。     

辐射换热对平板气膜冷却性能影响

为了分析辐射换热对平板气膜冷却性能的影响,分别对不考虑辐射换热(耦合计算)与考虑辐射换热两种条件下的平板隔热屏进行了三维流热耦合数值模拟研究,并与绝热壁(不考虑隔热屏固壁导热)的计算结果进行了对比。辐射换热采用离散坐标法。得到了3种不同主/次流总温比(Rt)条件下气膜冷却效果、流场、单位面积冷流体热负荷以及流量系数的对比结果与变化规律。结果表明:气膜冷却效果沿流向逐渐降低,且随总温比的增加而降低;在展向上气膜冷却效果呈现中间高两边低的分布规律,最大与最小相对值在绝热壁条件下达到最大,为94.5%,辐射换热次之,为13.5%,不考虑辐射换热时最小,为9.8%。与不考虑辐射换热结果相比,辐射换热对气膜冷却效果的影响在流动方向逐渐变大,气膜孔附近展向温度梯度增大,冷流体热负荷增加了92.8%,二者计算的流量系数相差不大,为1.1%,与绝热壁计算结果相比,流量系数减小了13.1%。随着总温比增加流量系数减小,最大值与最小值相差不大,为1.1%。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

舱内航天服散热途径分析

为分析常压下航天员穿着舱内航天服时的散热性能，６名健康男性青年按二次复合设计分组共进行２４人次试验，经分析计算了获得了服装各散热途径的散热率随通风气源参数及人体活动水平变化的数学模型。对影响服装散热性能的因素及服装散热特性进行了分析讨论。     

CONTROL OF TWO DIMENSIONAL JETS USING MINIATURE ZERO MASS FLUX JETS

Zero mass flux jets, synthesized by acoustic actuators, have been used for the purpose of jet mixing enhancement and jet vectoring. Zero mass flux jets composed of entirely entrained fluid allow momentum transfer into the embedding flow. In the present experiments, miniature-scale high aspect ratio actuator jets are placed along the long sides and near the exit plane of a primary two-dimensional jet. In different modes, the primary jet can be vectored either towards or away from the actuator jets and the jet mixing is enhanced. The disturbance of the excitation frequency is developed while the unstable frequency of the primary jet is completely suppressed.     

热管式表面温度计检定装置

叙述一种热管式表面温度计检定装置的原理、结构。该装置可用于航天领域在实验室条件下对表面温度计的检定。     

考虑轨道摄动的外热流计算分析

为改进传统外热流算法未考虑外热流经多次反射后的吸收和国外商业软件未考虑轨道摄动及太阳矢量变化对外热流的影响等不足,重新定义了外热流角系数和外热流辐射传递因子,综合SGP4轨道模型和Gebhart方法,给出了考虑摄动等因素的辐射传递因子和轨道外热流计算模型,以及相应的计算流程。通过仿真分析论证了考虑多次反射及摄动等因素的重要性。     

热流限制下的最优气动力辅助变轨

以变轨能量消耗最小为优化目标，应用极大值原理研究了飞行过程受热流限制和升力系统约束下的气动力辅助共面变轨问题，飞行过程成分第一自由弧段，约束弧段，第二自由弧段三个部分，讨论了升力系数的最优表达式，分析了飞行过程中两种约束的相互作用，给出了约束弧起始位置的角点条件和终端的横截条件下，对不同的初值选取方法讨论了三种计算策略，并给出了数值算例。