矩形截面弯管内气固两相流及对管壁磨损的数值分析

在便于描述矩形截面弯管流动的曲线坐标系中，计算了气固两相流，颗粒对管壁的磨损位置与磨损量。分析了弯管曲率、弯管安放方式、颗粒大小对磨损状况的影响。本文计算与实验数据比较，符合良好。     

相位信息在故障诊断中的应用

 在故障诊断中,人们多从频域中寻找特征,但对于转子系统,许多故障的特征是相似的。相位作为旋转机械里一个很实用的量,在故障诊断中一直没有得到很好的应用,本文指出的相位计算和测量概念和方法,旨在进一步识别故障。     

TiAl/IN718合金过渡液相连接

采用过渡液相TLP(Transient Liquid Phase)连接技术,以金属Ti,Cu,Ni箔构成复合焊料连接TiAl和IN718合金.研究了保温时间对接头界面结构的影响.实验结果表明:采用Ti-Cu,Ti-Ni复合焊料可以制备无缺陷的接头,但2种焊料形成液相的过程和机理不同.由于在等温凝固过程中,从IN718合金中扩散过来的合金元素可在焊缝区聚集,从而在接头中形成亚层结构.通过对接头焊缝区的组织分析和硬度测试表明,在实验条件下Ti-Ni焊料的等温凝固过程持续时间比Ti-Cu的短.     

Experimental and numerical investigation on surface quality for two-point incremental sheet forming with interpolator

The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator.     

比例与非比例加载下30CrMnSiA钢多轴高周疲劳失效分析

为了分析比例与非比例加载下,30CrMnSiA钢的多轴高周疲劳的失效规律。通过对30CrMnSiA钢材料开展比例与非比例(δ=90°)加载下的多轴高周疲劳试验,研究了应力幅比和相位差对疲劳寿命、断口特征及裂纹起裂角度的影响。试验结果表明,对于比例与非比例加载,随着应力幅比的增大,多轴疲劳寿命逐渐增加。对疲劳断口分析发现,裂纹萌生于试件表面,断口有明显的疲劳源区、扩展区和瞬断区,不同加载路径下的试件断口形式有明显差异。通过对起裂角度的分析发现,应力幅比大于0.25时表面裂纹有明显的第Ⅰ阶段向第Ⅱ阶段的转变,且第Ⅰ阶段沿着接近最大剪应力幅值平面方向扩展,第Ⅱ阶段沿着接近最大正应力平面方向扩展。此外,对典型试件的疲劳断口及表面扩展路径进行了分析,研究表明多轴疲劳试验试件裂纹的特征比值在0.3~0.5之间,且裂纹沿深度方向扩展至300 μm时占总寿命的85%以上。      

同步误差条件下的空间目标双基地ISAR自聚焦算法

以空间目标为研究对象，针对双基地雷达时间、空间及频率同步误差导致的逆合成孔径雷达图像散焦问题，提出基于离散多项式相位变换的自聚焦算法。算法首先将目标平动、转动及同步误差导致的相位项统一建模为高阶多项式，利用离散多项式相位变换方法估计高阶多项式系数并据此构建补偿相位项，完成高阶相位补偿。最后进行方位压缩得到高聚焦度的二维ISAR像。算法通过选取合适的延时参数及成像积累时间可得到高精度参数估计及相位补偿，理论分析和仿真校验了算法性能优于常用的非参数化自聚焦算法。     

NVNA谐波相位检验件设计及定标

本文介绍了一种用于检验非线性网络分析仪谐波相位指标的检验件设计方法，并搭建了基于实时示波器的测量系统对谐波相位进行定标。通过高速实时示波器对检验件的输出信号进行采样，利用傅立叶变换提取谐波相位信息。为了得到高准确度的测量结果，采用去缠绕、最小二乘等算法对相位结果进行优化处理。实验结果表明，该方法可以作为NVNA谐波相位指标的验证手段对NVNA的谐波相位进行验证。     

四相横向磁通永磁电机的三电平滞环电流控制

以新型四相横向磁通永磁电机为研究对象,利用MATLAB/Simulink软件平台以及Simpower System工具箱,对闭环控制系统进行了研究。在传统双闭环调速控制基础上,为滞环电流控制环引入零电平,将滞环分为上滞环和下滞环。综合考虑开关频率与电流THD确定合适的滞环环宽,并根据偏差电流值与滞环环宽比较值得到逆变器控制信号。通过仿真得到各种工况下的电机运行数据,说明该控制方法能够对四相横向磁通永磁电机进行有效控制。     

Carrier phase prediction method for GNSS precise positioning in challenging environment

Since the signals of global navigation satellite system (GNSS) are blocked frequently in challenging environments, the discontinuous carrier phases seriously affect the application of GNSS precise positioning. To improve the carrier phase continuity, this paper proposes a carrier phase prediction method based on carrier open-loop tracking. In the open-loop tracking mode, the carrier numerically controlled oscillator (NCO) is controlled by the predicted Doppler, but not by the loop filter output. To improve the phase prediction effective time, accurate receiver clock drift estimation is studied in the prediction method. The phase prediction performance is tested on GNSS software receiver. In the phase prediction effective time tests, open-loop processes were set for the tested channel. The test results show that, when some satellite signals are blocked in 15?s, the probability of carrier phase error less than quarter cycles is more than 94%. In the real time kinematic (RTK) positioning tests, some satellite signals are blocked in 10–15?s repeatedly. The test results show that, the carrier phase continuity is basically not affected by the signal interruption, and the RTK can almost keep continuous centimeter-level positioning accuracy without re-fixing the integer ambiguity.     

喷管潜入段二维两相冷流实验

建立了喷管潜入段二维两相冷流实验设备,进行了相应的实验。实验清晰地显示了在潜入喷管进口背壁凹区旋涡的产生、稳定、消失,以及粒子的冲刷、粘贴、脱落、沉积等反复作用的复杂现象,它们与流动的雷诺数、粒子的含量和尺寸、潜入喷管进口处的形状和潜入深度、背壁型面等因素有关。