脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

燃气轮机燃烧室预混喷嘴排放性能的试验和数值研究

为了研究当量比、值班燃料量和压力对燃气轮机燃烧室预混喷嘴排放指标的影响,在环境压力下按照等速模化原理进行了燃烧室预混喷嘴的燃烧试验,基于化学反应网络法构建了污染物预测模型,开展了试验和数值对比研究。结果表明:在带值班燃料的情况下该预混喷嘴当量比φ在0.35～0.5时可满足国标排放要求,但是值班燃料量增大会使NO_x排放升高;在φ0.4时,压力对纯预混燃烧NO_x生成无影响,φ0.4时,NO_x会随压力升高而增多;带有值班燃料的预混燃烧时,NO_x对压力变化敏感,压力升高导致NO_x增多;该预混喷嘴混合性能对空气流速不敏感、燃料兼容性强,排放达标当量比范围宽,经进一步设计开发后有潜力应用于燃气轮机低排放燃烧室中。该化学反应器网络模型依赖经验较少,当值班燃料比例≤0.17时,对污染物预测与试验数据符合较好。     

扫频式射流对涡轮叶栅间隙泄漏流动影响的数值研究

为控制涡轮叶栅中叶顶间隙泄漏流动和改善涡轮气动性能,将扫频式射流器(SJA)作为一种主动流动控制方法应用在涡轮叶栅的研究中。通过非定常数值计算,分析了SJA对涡轮叶栅叶顶间隙流动的作用过程以及作用机理,并且研究了不同工况下SJA对涡轮叶顶流场改善效果以及不同频率的SJA对叶顶流场的影响。结果表明:通过在涡轮叶栅上端壁增加单个SJA装置,可以有效地延迟上端壁的流动分离,其中最佳方案射流流量仅为进口总流量的0.35%,涡轮叶栅出口截面总压损失系数减少了11.48%。存在着最佳的频率284Hz,使SJA装置对流场的作用效果最佳,有效地改善了涡轮叶栅内的间隙流动。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

基于分解协调移动极值响应面法的多构件结构动态可靠性分析

多个构件装配而成的复杂结构可靠性分析存在计算流程繁琐、计算效率低的问题。基于极值响应面 法、移动最小二乘法和分解协调的策略,提出分解协调移动极值响应面法(DCMERSM),对考虑流-热-固耦 合作用的航空发动机高压涡轮叶盘径向变形进行动态可靠性分析,通过对比直接模拟和分解协调极值响应面 法(DCERSM),对 DCMERSM 在 建 模 特 性 和 仿 真 性 能 方 面 的 有 效 性 和 适 用 性 进 行 验 证。 结 果 表 明: DCMERSM不仅适用于转子机械动态可靠性分析,同时还可以用于复杂机械多构件结构可靠性分析。     

基于力约束的空心涡轮叶片陶芯定位方法

精铸蜡型作为空心涡轮叶片精铸过程重要的前期工艺转接件,其壁厚精度主要由蜡型模具型腔与内部陶芯的位置匹配关系决定。由于陶芯在模具内完全依靠定位元件实现空间定位,为减小由定位误差引起的陶芯位姿漂移,提出了一种基于力平衡约束的空心涡轮叶片精铸模具陶芯定位布局优化方法。首先,通过建立陶芯定位误差传递模型,揭示了定位误差与陶芯空间位姿扰动量之间的映射关系;其次,根据力平衡原理构建了基于力约束的陶芯定位布局优化模型;之后,针对陶芯表面定位候选点的离散分布特性,结合遗传算法给出了陶芯定位布局点的详细求解策略。最后,仿真对比证明了利用本文所提方法获得的陶芯定位方案可以在保证陶芯定位稳定性的同时提高陶芯定位精度,此外,按照优化后的定位方案压制实际蜡型,壁厚检测结果也进一步表明所提方法的有效性。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

风力机组叶片的先进翼型族设计

大型风力机组叶片设计需要专用的翼型族,以满足风力机组运行的环境要求。高升阻比、低粗糙度影响是该翼型族的气动性能特点。为了发展我国具有自主知识产权的风力机专用翼型族,在科技部863项目的支持下,北京航空航天大学联合国内气动研究单位,通过理论分析、数值模拟和风洞试验等技术途径,开发了两个适用于大型风力机组叶片的先进翼型族。理论分析和风洞试验表明,设计结果基本达到了预先设定的气动性能指标。     

气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。