引入杆位移抑制滤波器的驾驶员诱发振荡防范方法

对人-机闭环系统进行数学建模,基于 Neal-Smith频域准则,对建立的模型进行参数匹配。在该模型条件下,以对驾驶员诱发振荡(Pilot Induced Oscillation,PIO)现象的产生机理及诱发因素的研究为基础,深入探讨了在恶劣环境下 PIO的防范方法,并利用 Neal-Smith频域准则对该防范方法进行评估。通过开环特性和闭环特性分析,确立了引入杆位移抑制滤波器的方法来有效抑制 PIO的发生,为飞机设计研制过程中有效防范 PIO提供借鉴和参考。     

基于最临界约束准则法的机翼主承力结构优化

利用最临界约束准则法对某型飞机机翼主承力结构在强度，位移，扭转角，稳定性和尺寸约束下，以最小重量为目标函数进行了优化，并在实际操作过程中依据机翼结构的复杂性对最临界约束准则法做了相应的修改。结果表明，应用最临界约束准则法进行机翼结构优化时，效率较高，机翼结构重量稳定下降，优化效果明显。     

基于热力耦合层合板雷击损伤特性分析

为研究复合材料层合板在雷电流作用下的烧蚀损伤力学特性,建立复合材料雷击热力耦合有限元分析模型,与文献实验结果对比验证模型的有效性。根据Hashin三维失效准则编写用户材料子程序,分别得出层合板雷击烧蚀区域周围出现的力学损伤、各层力学损伤分布以及首层在不同方向上的应力分布,分析得出层合板的烧蚀损伤随雷电流持续时间的变化规律。结果表明:由于存在较高的温度梯度,导致层合板出现较大的热膨胀应力,进而导致层合板内部产生各种力学损伤,即基体开裂、分层及纤维断裂;雷击电流施加时间、峰值电流与温度场均对层合板烧蚀面积产生较大的影响。     

Experimental study of effect of post processing on fracture toughness and fatigue crack growth performance of selective laser melting Ti-6Al-4V

For Ti-6Al-4V, a titanium alloy increasingly used in aerospace structure, selective laser melting (SLM) is an attractive additive manufacturing technology, which is attributed to its complex construction capability with high accuracy and good surface quality. In order to obtain qualified mechanical properties, SLM parameters and post processing should be tailored for diverse service conditions. Fracture toughness and fatigue crack growth (FCG) behavior are critical characteristics for damage tolerance evaluation of such metallic structures, and they are affected by post processing technologies significantly. The objective of this study is to obtain the fracture toughness and fatigue crack growth behavior of Ti-6Al-4V manufactured by SLM, and to evaluate the influence of post-SLM thermomechanical treatment and surface machining. Fracture toughness and FCG tests were performed for SLM Ti-6Al-4V in three types of post processing status: as-built, heat treated and hot isostatically pressed (HIPed), respectively. Specimens with as-built and machined surface were tested. The microstructure and fractography were analyzed as well in order to investigate the relevance among manufacture process, microstructure and mechanical properties. The results demonstrate that as-built SLM Ti-6Al-4V presents poor ductility and FCG behavior due to martensitic microstructure and residual stresses. Both heat treatment and hot isostatic pressing improve the plane-stress fracture toughness and FCG performance considerably, while surface machining shows slight effect.     

A comparative study on acoustic damping induced by half-wave, quarter-wave, and Helmholtz resonators

The damping characteristics of three-type resonators, a half-wave, a quarter-wave, and a Helmholtz resonator are studied experimentally by adopting linear acoustic test. A quantitative acoustic property of sound absorption coefficient in a model enclosure with the resonators is measured and thereby, the acoustic-damping capacity of a resonator is characterized. For a comparative study on acoustic damping, the damping capacity of a half-wave resonator is compared with that of the other resonators. A half-wave and a quarter-wave resonators have the same damping mechanism, but a quarter-wave resonator has much larger damping capacity than a half-wave resonator with the same diameter of a single resonator. It is found that shorter length of a resonator has the advantage of longer one with respect to the damping capacity. The damping capacity of a Helmholtz resonator increases with cavity volume and does as the orifice length decreases. A Helmholtz resonator has the highest damping capacity of three-type resonators and a half-wave resonator has the lowest. Besides, a Helmholtz resonator requires the smallest number of resonators for optimal damping. The design criterion of each resonator on the optimal damping is provided by the normalized parameter of open-area ratio and the similarity behavior for the optimal damping is observed for various enclosure diameters.     

A new approach on necking constitutive relationships of ductile materials at elevated temperatures

A new method is presented to determine the full-range, uniaxial constitutive relationship of materials by tensile tests on funnel specimens with small curvature radius and finite element anal-ysis (FEA). An iteration method using FEA APDL (ANSYS parametric design language) program-ming has been developed to approach the necking constitutive relationship of materials. Test results from SAE 304 stainless steel at room temperature show that simulated load vs displacement curve, diameter at funnel root vs displacement curve, and funnel deformation contours are close to mod-eled results. Due to this new method, full-range constitutive relationships and true stress and effec-tive true strain at failure are found for 316L stainless steel, TA17 titanium alloy and A508-III stainless steel at room temperature, and 316L stainless steel at various elevated temperatures.     

论裂纹扩展J积分阻力曲线变化规律的影响因素

本文对大塑性变形条件下，裂纹稳定扩展过程的J积分阻力曲线变化规律进行了全面的分析。给出了不同约束条件下dJ／da与试样的载荷因子L、裂纹尖端张开角CTOA及裂纹扩展时的瞬时旋转中心的系数r之间的理论表达式。从而论证了不同约束条件下，试样的几何尺寸因素对其J阻力曲线变化趋势的影响规律。     

结构可靠性定寿模型及其在航空动力结构中的应用

本文以安全寿命定寿，以损伤容限保障安全，发展了结构可靠性定寿模型，给出了确定结构首翻期和检修周期公式；还给出了该模型应用于航空发动机动力构件疲劳定寿的实例     

俯仰轴飞行品质的PIO准则计算

由于新技术的采用,现代飞机出现驾驶员诱发振荡(PIO)现象大大增加,因此PIO已成为危及飞行安全的主要因素之一。介绍了MIL—STD—1797A规范中的PIO预测准则和美国“人机耦合对飞行安全影响委员会”提出的准则,论述了这些准则要求的背景、机理和计算方法,最后以某机为例进行了PIO预测计算和分析。     

时效工艺对高强度Al-Cu-Li合金断裂韧性的影响

采用Kahn撕裂法测试了高强度Al-Cu-Li合金2090在不同时效制度下的断裂韧性及其变化规律,并借助TEM和SEM对相应微观组织形貌及断口形貌进行了观察。结果表明:双级时效和应变时效均可促进T_1相析出,改善合金的断裂韧性,但这种促进作用在过时效状态下减弱;晶界PFZ的宽化和粗大晶界平衡相的析出降低合金的断裂韧性,并对时效工艺、微观组织及断裂韧性之间的关系进行了讨论。