针对星载 SA R的散射式干扰应用研究

针对星载SAR的特点,简述了散射波干扰的干扰原理,并针对其工程实现中的几个关键问题进行了分析。最后针对典型星载SAR进行了干扰验证试验,给出了试验结果,证明了该样式的有效性。     

KrF激光照射约束层靶驱动产生高速飞片研究

微小空间碎片的超高速撞击对航天器性能有重要影响。为了研究撞击损伤机制,在"天光一号"装置上开展了Kr F准分子激光照射约束层靶产生高速飞片的实验研究,利用成像速度干涉仪(Imaging-VISAR)对飞片自由面速度进行诊断。采用1.9 J准分子激光将10μm的Al飞片加速至12 km/s,且整个过程为准等熵加载。研究结果表明准等熵加载下激光能量转化为飞片动能的效率(达39.4%)比冲击加载要高得多,飞片速度也高于后者。     

高空环境下喷嘴参数对航空活塞发动机燃烧与性能的影响

以一台四缸四冲程压燃式航空煤油活塞发动机为研究机型,运用工程系统高级建模和仿真平台软件(AMESim)仿真软件建立了发动机的整机模型,并使用台架实验的采集数据对该仿真模型进行了验证。在高空环境中,仿真分析了飞行器起飞工况、最大巡航工况下发动机喷油器的不同喷孔数、孔径对发动机燃烧过程、性能和NOx排放特性的影响。计算结果表明:稳态工况下,随着喷孔数的增加,最高燃烧压力和温度增加,瞬时放热率增长速度快且峰值上升;同时,缸内预混燃烧得到强化,燃烧始点提前,滞燃期和燃烧持续期缩短,燃烧重心前移,循环热效率增高,但同时会提高NOx的生成量;在飞行器瞬态变海拔的起飞工况下,多喷孔数、小孔径的喷油嘴有利于航空活塞发动机在高空环境下恢复发动机功率,提升飞行器的动力性和续航性能。      

高温高压下平板预膜喷嘴初次雾化试验

为了深入探究预膜喷嘴燃油初次雾化机理,试验研究了高温高压条件下不同工况参数对平板预膜喷嘴初次雾化特性的影响规律.采用高速摄影可视化技术和马尔文粒度仪获取了预膜平板液膜厚度、液膜波动形态以及索泰尔平均直径(SMD)等雾化特性.利用图像后处理技术提取液膜厚度,试验结果表明:液膜厚度随进气压力、进气温度和进口韦伯数的增加而减...     

Microstructural characterization and mechanical behavior analysis of 7075-T6 aluminum subjected to simulated lightning strikes

Aircrafts damages caused by lightning strikes have been known since the early days of aviation. However, the physical effects on the aircraft structure are still being investigated. This work seeks to evaluate the lightning strike effects in the aluminum alloy 7075-T6. Samples were submitted to lightning strike simulation in laboratory and the damages evaluated through characterization techniques. Ultrasound and profilometry tests have shown material loss to 0.272 mm depth in the damaged region. In addition, it was detected the material accumulation occurrence in the damage vicinity of the region. Below the damage, it was found a region where metallurgical changes were identified. The tensile and microhardness tests results have shown reduction in the percentage elongation and hardness increasing in the material affected by lightning. These results are corroborated by the X-Ray Diffraction (XRD) and Rietveld Method (red line) that indicated an increasing in dislocation density and micro-deformation in the material matrix. Optical microscopy results have shown the presence of microcracks on the normal and cross-section surface of the samples damaged. The Energy Dispersive X-Ray Spectroscopy (EDXS) and Electron Backscattered Diffraction Test (EBSD) found coarse intermetallic phases and precipitates compounds with dimensions greater than 1 μm in length. They were responsible for nucleation of the microcracks that propagate along the material grain boundaries.     

Civil unmanned aircraft system operation in national airspace: A survey from Air Navigation Service Provider perspective

Unmanned Aircraft Systems (UASs) have advanced technologically and surged exponentially over recent years. Currently, due to safety concerns, most civil operations of UAS are conducted in low-level uncontrolled area or in segregated controlled airspace. As the industry progresses, both operational and technological capabilities have matured to the point where UASs are expected to gain greater freedom of access to both controlled and uncontrolled airspace. Extensive technical and regulatory surveys have been conducted to enable the expanded operations. However, most surveys are derived from the perspective of UAS own operating mechanism and barely consider interactions of their non-segregated activities with the Air Traffic Management (ATM) system. Hence, to fill the gap, this paper presents a survey conducted from the perspective of Air Navigation Service Provider (ANSP), which serves to accommodate these new entrants to the overall national airspace while continuing flight safety and efficiency. The primary objectives of this paper are to: (A) describe what typical ANSP-supplied UAS Traffic Management (UTM) architecture is required to facilitate all types of civil UAS operations; (B) identify three major ANSP considerations on how UAS can be accommodated safely in civil airspace; (C) outline future directions and challenges related with UAS operations for the ANSP.     

基于神经网络的导弹制导控制一体化反演设计

针对制导控制一体化(IGC)模型中的不确定性难以进行估计补偿的问题,提出了基于神经网络的IGC反演设计方法。首先,根据弹目相对运动关系以及导弹自动驾驶仪模型建立了三维空间中的IGC模型。其次,针对由目标机动引起的模型不确定性,提出应用高阶滑模微分器(SMD)对导弹导引头获得的弹目相对运动信息进行微分,从而估计出目标加速度的方法,然后考虑导弹自身由于参数摄动以及未建模动态引起的模型不确定性,应用SMD和神经网络模型进行在线逼近补偿,基于反演控制理论设计了带有SMD和神经网络模型的IGC算法,应用李雅普诺夫稳定性理论对所设计的控制算法进行了稳定性证明。最后,进行了导弹六自由度仿真,验证了所设计控制算法的有效性。     

基于云映射的多粒度语义决策属性识别

异类多传感器多属性目标识别中的描述性语义和决策属性信息无法直接进行识别判定,为此基于粒层转化的思想,提出了一种语义和决策属性识别方法。首先构造云映射函数,将语义和决策属性粒层统一到区间粒层,再根据灰色关联的思想计算区间化后的语义和决策属性信息与数据库之间的区间关联度,实现了不等粒层属性的粒度计算,最后采用证据推理进行了识别判定。结合语义和决策属性识别算例及对比分析,验证了所提出方法在异类数据模糊转化处理和识别上的有效性。     

星载平面可展天线支撑桁架的结构效率优化

针对折展结构性能存在多指标且这些指标之间又相互制约的特点,把结构效率引入到可展结构的优化设计中,应用多因素正交试验法对一种空间可展开平板天线支撑桁架的优化问题进行了研究。对其关键几何设计参数进行了分析,建立了桁架结构的优化数学模型,以结构效率最大化作为优化目标,对可展桁架进行了结构优化,得到了支撑桁架各杆件的设计参数。结果表明:结构效率综合考虑了质量和刚度的影响,使结构质量和刚度同时得到优化;长宽比(l/w)是影响可展桁架结构性能的主要因素,对不同优化目标产生影响的次要因素有所不同;截面积对结构效率影响不显著(置信度p=90%),在相同杆长参数配置下,等截面可展桁架的结构效率仅次于变截面方案,但工程经济性最佳。该研究方法有助于在概念设计阶段从系统设计的角度进行空间桁架结构的快速设计与优化。     

环形中心钝体驻涡燃烧室驻涡腔有无喷射的对比

采用三维雷诺平均Navier-Stokes(N-S)方程、renormalization group (RNG) k-ε湍流模型和标准壁面函数对驻涡腔有无喷射的环形中心钝体驻涡燃烧室的冷态流场进行了数值仿真,分析了驻涡腔有无喷射对环形中心钝体驻涡燃烧室涡系结构、驻涡腔流动参数和燃烧室总体性能的影响.结果表明:相比于无喷射时,驻涡腔添加喷射可以使驻涡腔内形成相对稳定的双驻涡结构;驻涡腔喷射的存在使得环形中心钝体驻涡燃烧室出口截面总压损失系数降低约9.2%,并能提高驻涡腔内的平均气流参数;驻涡腔喷射对环形中心钝体驻涡燃烧室出口截面流动参数沿流道高度方向的变化趋势影响不大.