多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

飞机变形自动化测量方法研究

为解决以往飞机变形测量模式中人工干预较多,受测量环境影响较大,测量时间长等问题,基于Geo COM技术和RS232,在计算机与全站仪之间进行数据交换,设计了一套自动化测量系统。在测量过程中由标志点的机体理论坐标反算其在当前测站中的极坐标,从而在测量过程中驱动全站仪指向待测点,减少人工瞄准时间,并由计算机实时解算结果数据。经实际飞行试验验证表明,测量时间缩短为原来时间一半,大大提高了工作效率。     

跨介质航行器波浪环境入水流场演变和运动特性研究

跨介质航行器是一种既可以在空中飞行又可以在水下潜航的新概念航行器,基于仿生学原理,提出一种通过改变外形实现水空介质跨越的航行器模型,通过入水试验装置和计算流体动力学方法,对航行器带攻角从空气到水的介质跨越过程进行了试验和数值仿真研究,得到了跨介质入水过程航行器的运动姿态和入水空泡形态,并通过数值仿真得到了航行器的升力、阻力、速度和加速度演化规律。同时基于数值模拟方法对有波浪情况和静水情况下航行器入水过程空泡演变以及运动特性进行对比。结果表明:提出的航行器构型在水中具有较好的姿态调整能力,波浪的有无和波高的不同都会对航行体入水运动特性造成影响。     

大涵道比风扇/增压级进气畸变数值模拟研究

为探究进口总压畸变下大涵道比风扇/增压级内部流场的主要特征，基于三维彻体力模型的思想，开发了一套能够实现风扇/增压级内外涵联算功能的三维数值计算程序。利用该程序模拟了某大涵道比风扇/增压级在周向总压畸变进气下的三维流场。计算结果表明：大涵道比风扇单转子不同叶高处的畸变传递特征差异较大，转子出口总压畸变强度由叶根到叶尖逐渐降低，在叶尖处衰减为最小值1.5%；在转子出口相应诱导出的总温畸变强度由叶根到叶尖逐渐升高，在叶尖处达到最大值1.4%；进口周向总压畸变导致风扇转子总压比下降0.5%，而风扇转子出口形成的总压总温复合畸变导致增压级总压比下降2%；总压畸变在增压级中呈逐级衰减趋势，而高温畸变区的周向范围在逐级增加。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

Geometric calibration of Colour and Stereo Surface Imaging System of ESA’s Trace Gas Orbiter

There are many geometric calibration methods for “standard” cameras. These methods, however, cannot be used for the calibration of telescopes with large focal lengths and complex off-axis optics. Moreover, specialized calibration methods for the telescopes are scarce in literature. We describe the calibration method that we developed for the Colour and Stereo Surface Imaging System (CaSSIS) telescope, on board of the ExoMars Trace Gas Orbiter (TGO). Although our method is described in the context of CaSSIS, with camera-specific experiments, it is general and can be applied to other telescopes. We further encourage re-use of the proposed method by making our calibration code and data available on-line.     

Experimental study on plasma jet deflection and energy extraction with MHD control

This paper presents an integrated research scheme for vector deflection and energy extraction in a gas plasma jet under Magneto-Hydrodynamic (MHD) control. A MHD-controlled thrust-vector test rig was used to conduct the experimental research. A gas plasma was obtained by injecting ionization seeds of Cs₂CO₃ into the combustion chamber via artificially forced ionization. The effects of the gas temperature and ionization seed mass fraction on the plasma jet deflection and energy extraction were experimentally verified under an applied magnetic field. The experimental results were analyzed theoretically. The results showed that the deflection amplitude of the gas plasma jet and the extracted voltage signal intensity increased with increasing gas temperature and the ionization seed mass fraction. The extracted dynamic voltage signals proved that the ionization seeds of Cs₂CO₃ induced gas ionization at 1173 K. The experiment verified that it is feasible to simultaneously achieve jet deflection and extract energy under the action of an external magnetic field.     

加筋壁板VARI整体成型工艺设计与验证术

针对一种典型复合材料加筋壁板,完成模具结构及工艺流程等整体成型工艺设计,同时利用PAM-RTM软件完成流道设计优化模拟,并根据模拟结果选择合理的注射方式及流道布局,最终根据所选方案完成工艺试验验证,对构件进行超声无损检测,检测结果显示构件没有内部缺陷、树脂充分填充,最终验证了加筋壁板整体成型工艺设计及模拟分析的有效性.     

双层多支板流道组合件变形控制

双层多支板流道组合件是薄壁焊接机匣,与涡轮后机匣和外支撑环组合件连接,是低压涡轮部件上的重要连接、承力件.该件焊缝密集,结构刚性差,安装边连接孔和篦齿环槽口位置度、尺寸精度高,加工难度大.采用多种工艺措施控制焊接变形,增加辅助支撑减小加工变形,综合运用筒体胀形、焊接、激光切孔、机械加工等加工工艺,实现了薄壁双层多支板流道组合件制造.