国产T700级碳纤维增强双马树脂基复合材料的力学性能

采用扫描电子显微镜(SEM)、反气相色谱(IGC)和X射线光电子能谱仪(XPS)对国产T700级碳纤维和东丽T700S碳纤维的表面形貌、表面能和表面化学特性进行表征,测试两种碳纤维增强双马树脂基复合材料的力学性能,考察国产碳纤维复合材料的界面黏结性能、韧性和湿热性能。结果表明:碳纤维表面特性(表面形貌、表面能和表面化学组成等)对复合材料界面黏结性能具有显著影响;国产T700级碳纤维/QY9611复合材料在室温下的界面黏结性能优于T700S/QY9611复合材料;国产T700级碳纤维/QY9611复合材料的韧性优异,冲击后压缩强度达到了国外先进复合材料IM7/5250-4的水平;经湿热处理后的层间剪切强度仍与T700S/QY9611复合材料相当,说明国产T700级碳纤维/QY9611复合材料具备良好的湿热性能。     

硅橡胶/双酚A-苯胺型苯并噁嗪树脂耐烧蚀复合材料的制备与烧蚀结构的研究

苯并噁嗪树脂具有优异的成炭和抗高温氧化性能,是新一代的耐烧蚀树脂。以双酚A-苯胺型苯并噁嗪树脂为耐烧蚀树脂,采用1H-NMR、DSC和转矩流变仪研究其成环率和加工性能;以硅橡胶为耐烧蚀基体,采用熔融共混方法制备了硅橡胶苯并噁嗪树脂耐烧蚀复合材料。进行力学和氧乙炔焰烧蚀检测,利用FT-IR、Raman和SEM研究复合材料综合性能和烧蚀结构。结果表明:苯并噁嗪树脂能够明显提高硅橡胶复合材料的耐烧蚀性能,当树脂添加量为20份时,复合材料具有较好的耐烧蚀和力学性能;该复合材料经过氧乙炔焰烧蚀后,烧蚀层形成表面陶瓷层、裂解炭化层和基体层。表面陶瓷层主要由SiO_2,SiC和C组成,裂解炭化层的主要组由C,SiO_2,SiC以及炭化彻底的碳和炭化不完全的有机结构组成。     

FCD1软脆光学镜片的高效研磨加工

针对FCD1软脆光学镜片高效高成品率的精密加工问题,本研究提出了一种使用复合结合剂金刚石丸片的精研加工技术,其金刚石丸片研具采用了金属、树脂和添加剂等复合结合剂。在精研过程中,丸片表层金刚石磨粒对工件的切深一致性避免了工件表面易出现的深划痕,可有效减少后道抛光工序加工时间,从而提高FCD1软脆光学镜片的生产效率和成品率。     

A compliant polymorphing wing for small UAVs

This paper presents the development of a novel compliant polymorphing wing capable of chord and camber morphing for small UAVs. The morphing wing can achieve up to 10% chord extension and ±20° camber changes. The design, modeling, sizing, manufacturing and mechanical testing of the wing are detailed. The polymorphing wing consists of one continuous front spar fixed to the fuselage and a rear spar on each side of the wing. Each rear spar can translate in the chordwise direction (chord morphing) and rotate around itself (camber morphing). A flexible elastomeric latex sheet is used as the skin to cover the wing and maintain its aerodynamic shape whilst allowing morphing. The loads from the skin are transferred to the spars using the compliant cellular ribs that support the flexible skin and facilitate morphing. Pre-tensioning is applied to the skin to minimize wrinkling when subject to aerodynamic and actuation loads. A rack and pinion actuation system, powered by stepper motors, is used for morphing. Aero-structural design, analysis and sizing are conducted. Performance comparison between the polymorphing wing and the baseline wing (non-morphing) shows that chord morphing improves aerodynamic efficiency at low angles of attack while camber morphing improves efficiency at high angles of attack.     

Effect of curing condition on bonding quality of scarf-repaired composite laminates

Both single-face vacuum bag curing (SVC) and double-face vacuum bag curing (DVC) can be used in scarf repair of composite structures. But different curing conditions caused by the sealing state may affect the bonding quality of scarf-repaired structures. In this paper, the effect of curing condition on bonding quality of scarf-repaired laminates was experimentally investigated in terms of surface profiles, moisture absorption curves and section profiles. In order to further explore the moisture absorption mechanism, finite element model of the repaired laminates using DVC was established with moisture diffusion of both the adhesive and composite laminates considered. This model was verified by experimental results. Based on the model of DVC case, the model of SVC case was built by changing moisture absorption parameters of the adhesive. Results show that SVC reduces the bonding quality, mainly reflecting in more adhesive inner voids and patch-to-parent dislocation. And SVC increases moisture absorption rate and moisture equilibrium content of the adhesive, and its effect on the former is far greater than that on the latter.     

永磁同步电机驱动太阳翼扰动力矩建模与仿真

建立太阳翼驱动机构(SADA)永磁同步电机的电磁方程，并利用固定界面模态综合法建立SADA驱动太阳翼耦合系统的振动方程；设计模拟柔性负载，对SADA驱动该柔性负载的扰振力矩进行仿真分析。结果表明，SADA驱动柔性负载运行过程中所产生扰振力矩主要由两个原因引起：1)电流噪声引起的力矩波动；2)控制参数选取不当引起的转角波动。     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。     

C/C素坯密度对GSIC/C-SiC复合材料摩擦磨损性能的影响

采用气相渗硅工艺(GSI)制备C/C-Si C复合材料,研究了C/C素坯密度对GSI C/C-Si C复合材料物相组成与摩擦磨损性能的影响,分析了C/C-Si C复合材料的制动过程,并归纳了其摩擦磨损机理。结果表明,随着C/C素坯密度的增大,GSI C/C-Si C复合材料的密度呈递减趋势,且C含量和开气孔率逐渐增加,而Si C含量和残余Si含量逐渐减少;自对偶条件下,复合材料的平均摩擦系数、磨损率均呈现先增大后减小的趋势,当C/C素坯密度为1.25g/cm3时有最大值,而制动稳定系数则不断增大。GSI C/C-Si C复合材料的制动过程是犁沟效应和粘着效应共同作用的结果,制动初始阶段和刹停阶段以犁沟效应为主,中间阶段以粘着效应为主。     

航空复合材料智能敲击检测方法研究

复合材料在生产和制造过程中难免会存在缺陷和损伤,严重影响着航空安全。敲击检测是最简单、运用最广泛的无损检测方法,然而其向智能化方向发展过程中出现了诸多问题。对复合材料结构特性、缺陷和损伤、安全性、敲击检测原理、敲击锤设计、信号处理单元、数据库搭建和智能检测算法进行了深入研究,提出了敲击检测标准流程和规范、数据库搭建方法、以及智能聚类检测算法,在此基础上开发了智能敲击检测系统。     

高性能纤维增强树脂基复合材料3D打印及其应用探索

纤维增强树脂基复合材料具有优异的力学性能,能够实现轻质、高性能结构的制造,但传统的成型工艺过程复杂、成本高,难以实现纤维回收利用,限制了纤维增强树脂基复合材料的广泛应用.3D打印技术是一种新兴的零件成形工艺,将3D打印技术应用于纤维增强树脂基复合材料的制造,为实现复合材料低成本、绿色制造提供了可能性.综述了纤维增强树脂基复合材料3D打印技术研究的发展现状,提出了一种高性能连续纤维增强热塑性复合材料3D打印工艺及其回收再制造策略.